ASTM B756 - 00(2011)

    Standard Specification for Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06110) Rod and Bar

    Active Standard ASTM B756 | Developed by Subcommittee: B02.07

    Book of Standards Volume: 02.04


      Format Pages Price  
    PDF 5 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $43.00   ADD TO CART


    Abstract

    This specification covers UNS N06110 nickel-chromium-molybdenum-tungsten alloy hot-worked rods and bars and cold-worked rods. The chemical compositions and mechanical properties of the materials should conform to the requirements in this specification.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers nickel-chromium-molybdenum-tungsten (UNS N06110) in the form of hot-worked rod and bar and cold-worked rod in the conditions shown in Table 1.

    1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

    TABLE 1 Mechanical Properties

    Condition and Diameter
    or Distance Between
    Parallel Surfaces in.
    (mm)
    Tensile
    Strength
    min, ksi
    (MPa)
    Yield
    Strength
    (0.2%
    Offset),
    min, ksi
    (MPa)
    Elongation
    in 2 in.
    or 50 mm
    or 4D, min,
    %
    Cold-worked rods and
    hot-worked rod and bar,
    annealed:
    Up to 4 (102), incl95 (655)45 (310)60
    Over 4 (102) to 10 (254), incl90 (621) 40 (276)50
    Forging quality (all sizes)AAA

    A Forging quality is furnished to chemical requirements and surface inspection only. No tensile properties are required.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B755 Specification for Nickel-Chromium-Molybdenum-Tungsten Alloys (UNS N06110) Plate, Sheet, and Strip

    B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys

    E8 Test Methods for Tension Testing of Metallic Materials

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    E1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys


    UNSPSC Code

    UNSPSC Code 11101711(Non ferrous alloy)


    Referencing This Standard

    DOI: 10.1520/B0756-00R11

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM B756-00(2011), Standard Specification for Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06110) Rod and Bar, ASTM International, West Conshohocken, PA, 2011, www.astm.org

    Back to Top