ASTM B572 - 06(2016)

    Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Rod

    Active Standard ASTM B572 | Developed by Subcommittee: B02.07

    Book of Standards Volume: 02.04


      Format Pages Price  
    PDF 4 $40.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $40.00   ADD TO CART


    Abstract

    This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556 in the form of rod for heat resisting and general-corrosive service. The material shall conform to the required chemical composition for nickel, iron, chromium, cobalt, molybdenum, tungsten, carbon, silicon, manganese, phosphorus, sulfur, columbium, tantalum, aluminum, zirconium, lanthanum, nitrogen, boron, and titanium. The mechanical properties of the material at room temperature shall conform to the prescribed values of tensile strength, yield strength, and elongation. The alloys shall undergo chemical analysis and mechanical testing, sampling for chemical analysis, and sampling for mechanical testing.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification2 covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R305563 in the form of rod for heat resisting and general-corrosive service.

    1.2 The following products are covered under this specification:

    1.2.1 Rods 5/16 to 3/4 in. (7.94 to 19.05 mm) exclusive in diameter, hot or cold finished, solution-annealed, and pickled or mechanically descaled.

    1.2.2 Rods 3/4 to 31/2 in. (19.05 to 88.9 mm) inclusive in diameter, hot or cold finished, solution annealed, ground, or turned.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys

    E8 Test Methods for Tension Testing of Metallic Materials

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    E1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys


    UNSPSC Code

    UNSPSC Code


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/B0572-06R16

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM B572-06(2016), Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Rod, ASTM International, West Conshohocken, PA, 2016, www.astm.org

    Back to Top