ASTM B514 - 05(2014)

    Standard Specification for Welded Nickel-Iron-Chromium Alloy Pipe

    Active Standard ASTM B514 | Developed by Subcommittee: B02.07

    Book of Standards Volume: 02.04


      Format Pages Price  
    PDF 3 $38.00   ADD TO CART
    Hardcopy (shipping and handling) 3 $38.00   ADD TO CART


    Abstract

    This specification covers nickel-iron-chromium alloys in the form of welded, cold-worked, and annealed pipe for general corrosive service and heat resisting applications. These products are furnished three alloys: UNS N08120, UNS N0880, and UNS N08810. The materials shall conform to the required chemical composition for nickel, chromium, iorn, manganese, carbon, copper, silicon, sulfur, aluminum, titanium, columbium, molybdenum, phosphorus, tungsten, cobalt, and nitrogen. The materials shall conform to the requred mechaniical properties such as tensile strength, yield strength, and elongation. A transverse sample representing the full wall thickness of annealed alloys UNS N08120 and N08810 shall conform to the average grain size. Pipe shall be capable of withstanding, without cracking, flattening under a load applied gradually. Each piece of each lot shall be subjected to hydrostatic test, pneumatic test, eddy current test, ultrasonic test, leak test, electric test, and transverse guided bend test.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification2 covers nickel-iron-chromium alloys in the form of welded, cold-worked, and annealed pipe for general corrosive service and heat-resisting applications. These products are furnished in three alloys: UNS N08120, UNS N08800, and UNS N08810.3 Alloy UNS N08800 is employed normally in service temperatures up to and including 1100°F (593°C). Alloys UNS N08120 and UNS N08810 are employed normally in service temperatures above 1100°F where resistance to creep and rupture is required, and are annealed to develop controlled grain size for optimum properties in this temperature range.

    1.2 This specification covers outside diameter and nominal wall pipe shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of the specification.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B775 Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe

    B899 Terminology Relating to Non-ferrous Metals and Alloys

    ANSI Standard

    B36.19 Stainless Steel Pipe Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.


    ICS Code

    ICS Number Code 77.150.40 (Nickel and chromium products)

    UNSPSC Code

    UNSPSC Code


    Referencing This Standard

    DOI: 10.1520/B0514-05R14

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM B514-05(2014), Standard Specification for Welded Nickel-Iron-Chromium Alloy Pipe, ASTM International, West Conshohocken, PA, 2014, www.astm.org

    Back to Top