This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556 nickel alloy billets and bars for reforging. The products shall be hot worked from ingots by rolling, forging, extruding, hammering, or pressing. The material shall conform to the chemical composition requirements prescribed by the reference material. The chemical composition of the material shall be determined by chemical analysis in accordance with test method E1473.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N10362, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556* billets and bars for reforging.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
E1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
bar; billet; UNS N06002; UNS N06030; UNS N06035; UNS N06022; UNS N06200; UNS N06230; UNS N06600; UNS N06617; UNS N06625; UNS N08020; UNS N08024; UNS N08026; UNS N01820; UNS N08367; UNS N08926; UNS N10242; UNS N10276; UNS N10665; UNS N10675; UNS N12160; UNS R20033; UNS R30556; UNS N06059; UNS N06686; UNS N10629; UNS N08031; UNS N06045; UNS N06025; Billets--Ni/Ni alloy; Carpenter alloy--specifications; Chromium-nickel-iron-molybdenum-copper alloy; Forgings--specifications; Nickel alloy rod/bar/wire--specifications; Nickel-chromium alloys--specifications; Nickel-iron alloy--specifications; Nickel-iron-chromium alloys--specifications; Reforging; UNS N08020 (Ni-Fe-Cr alloy, Carpenter 20Cb3); UNS N08024 (Cr-Ni-Fe-Mo-Cu alloy, columbium stabilized); UNS N08026 (Ni-Cr wrought alloy, Carpenter 20Mo6); UNS N08367 (Cr-Ni-Mo-N alloy, AL 6XN); UNS N08926 (Ni-Fe-Cr-Mo-Cu-N alloy, low C, N modified); UNS R20033 (Cr-Ni-Fe-Mo austenitic stainless steel, Alloy 33) ; ICS Number Code 0556
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]