ASTM B443 - 00(2009)

    Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) and Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219)* Plate, Sheet, and Strip

    Active Standard ASTM B443 | Developed by Subcommittee: B02.07

    Book of Standards Volume: 02.04


      Format Pages Price  
    PDF 8 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 8 $43.00   ADD TO CART
    Standard + Redline PDF Bundle 16 $51.60   ADD TO CART


    Abstract

    This specification covers rolled nickel-chromium-molybdenum-columbium alloy (UNS No. N06625) and nickel-chromium-molybdenum-silicon alloy (UNS No. N06219) plates, sheets, and strips. N06625 alloys shall be furnished in two grades of different heat treatment conditions, namely: Grade 1 (annealed); and Grade 2 (solution annealed). N06219 alloys, on the other hand, shall be furnished in solution annealed condition only. Materials shall be sampled prepared, and tested accordingly to examine their conformance to dimensional (thickness, weight, width, diameter, length, straightness, edges, squareness, and flatness), mechanical (tensile and yield strengths, and elongation), and chemical composition requirements.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers rolled nickel-chromium-molybdenum-columbium alloy (UNS N06625) and nickel-chromium-molybdenum-silicon alloy (UNS N06219)* plate, sheet, and strip.

    1.1.1 Alloy UNS N06625 products are furnished in two grades of different heat-treated conditions:

    1.1.1.1 Grade 1 (Annealed)Material is normally employed in service temperatures up to 1100°F (593°C).

    1.1.1.2 Grade 2 (Solution Annealed)Material is normally employed in service temperatures above 1100°F (593°C) when resistance to creep and rupture is required.

    Note 1—Hot-working or reannealing may change properties significantly, depending on working history and temperatures.

    1.1.2 Alloy UNS N06219 is supplied in solution annealed condition only.

    1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B446 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) Rod and Bar

    B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys

    E8 Test Methods for Tension Testing of Metallic Materials

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys


    ICS Code

    ICS Number Code 77.150.40 (Nickel and chromium products)

    UNSPSC Code

    UNSPSC Code


    DOI: 10.1520/B0443-00R09

    ASTM International is a member of CrossRef.

    ASTM B443

    Citing ASTM Standards
    Back to Top