ASTM B422 / B422M - 15

    Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip

    Active Standard ASTM B422 / B422M | Developed by Subcommittee: B05.01

    Book of Standards Volume: 02.01


      Format Pages Price  
    PDF 5 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $43.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $51.60   ADD TO CART


    Abstract

    This specification establishes the requirements for sheets and strips of copper-aluminum-silicon-cobalt, copper-nickel-silicon-magnesium, copper-nickel-silicon, copper-nickel-aluminum-magnesium, and copper-nickel-tin alloys with Copper Alloy UNS Nos. C19010, C19020, C19025, C63800, C64725, C70250, C70260, and C70265. Materials shall be tested and shall conform to dimensional (thickness, width, length, straightness, and edges), mechanical (tensile and yield strength, elongation, and ductility or formability), electrical resistivity, chemical composition requirements.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification establishes the requirements for2 Copper Alloy UNS Nos. C19002, C19010, C19015, C19020, C19025, C63800, C64725, C70250, C70260, C70265, and C70310 sheet and strip.

    1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.

    1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar

    B248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)

    B846 Terminology for Copper and Copper Alloys

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)


    ICS Code

    ICS Number Code 77.150.30 (Copper products)

    UNSPSC Code

    UNSPSC Code 30262300(Copper sheets); 30262400(Copper ingots strip billets and coil)


    Referencing This Standard

    DOI: 10.1520/B0422_B0422M-15

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM B422 / B422M-15, Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip, ASTM International, West Conshohocken, PA, 2015, www.astm.org

    Back to Top