ASTM B209M - 14

    Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)

    Active Standard ASTM B209M | Developed by Subcommittee: B07.03

    Book of Standards Volume: 02.02


      Format Pages Price  
    PDF 26 $62.00   ADD TO CART
    Hardcopy (shipping and handling) 26 $62.00   ADD TO CART
    Standard + Redline PDF Bundle 52 $74.40   ADD TO CART


    1. Scope

    1.1 This specification covers aluminum and aluminum alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2 and 4, and in the following finishes:

    (A) Limits are in mass percent maximum unless shown as a range or stated otherwise.
    (B) Analysis shall be made for the elements for which limits are shown in this table.
    (C) For purposes of determining conformance to these limits, an observed value or a calculated value attained from analysis shall be rounded to the nearest unit in the last right hand place of figures used in expressing the specified limit, in accordance with the Rounding Method of Practice E29.
    (D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered non-conforming. The Total for Other Elements does not include elements shown in the footnotes with specific composition limits.
    (E) Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.
    (F) Vanadium 0.05 max. The total for other elements does not include vanadium.
    (G) The aluminum content shall be calculated by subtracting from 100.00 % the sum of all metallic elements present in amounts of 0.010 % or more each, rounded to the second decimal before determining the sum.
    (H) Composition of cladding alloy as applied during the course of manufacture. Samples from finished sheet or plate shall not be required to conform to these limits.
    (I) Vanadium, 0.05–0.15, zirconium, 0.10–0.25.
    (J) 0.05–0.25 Zr.
    (K) Gallium 0.03 max, vanadium 0.05 max.
    (L) 0.10–0.6 Mn + Cr.
    (M) In case there is a discrepancy in the values listed in Table 1 with those listed in the “International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys” (known as the “Teal Sheets”), the composition limits registered with the Aluminum Association and published in the “Teal Sheets” shall be considered the controlling composition. The “Teal Sheets” are available at http://www.aluminum.org/tealsheets.
    (A) To determine conformance to this specification, each value for tensile strength and for yield strength shall be rounded to the nearest 1 MPa and each value for elongation to the nearest 0.5 %, both in accordance with the Rounding Method of Practice E29.
    (B) The basis for establishment of mechanical property limits is shown in Annex A1.
    (C) Elongations in 50 mm apply for thicknesses up through 12.50 mm and in 5× diameter for thicknesses over 12.50 mm.
    (D) Materials in either of these tempers, (H32 or H22), (H34 or H24), (H36 or H26), (H38 or H28), (H12 or H22), (H14 or H24), (H16 or H26), (H18 or H28), may be supplied at the option of the supplier, unless one is specifically excluded by the contract or purchase order. When ordered as H2X tempers, the maximum tensile strength and minimum yield strength do not apply. When H2X tempers are supplied instead of ordered H1X or H3X tempers, the supplied H2X temper material shall meet the respective H1X or H3X temper tensile property limits.
    (E) Tests of F temper plate for tensile properties are not required.
    (F) The tension test specimen from plate over 12.50 mm in thickness is machined from the core and does not include the cladding alloy.
    (G) This material is subject to some recrystallization and an attendant loss of brightness.

     

    Alloy

    Temper

    Specified Thickness,
    mm

    Axis of
    Test Specimen

    Tensile Strength,
    MPa

    Yield Strength
    (0.2 % offset), MPa

    Elongation,C
    min, %

    over

    through

    min

    max

    min

    max

    in 50 mm

    in 5× 
    Diameter

    2124

    T851E

     25.00

     50.00

    longitudinal

    455

    ...

    395

    ...

    ...

    5

    2124

    T851E

     

     

    long transverse

    455

    ...

    395

    ...

    ...

    4

    2124

    T851E

     

     

    short transverse

    440J

    ...

    380J

    ...

    ...

    1

    2124

    T851E

     50.00

     80.00

    longitudinal

    450

    ...

    395

    ...

    ...

    5

    2124

    T851E

     

     

    long transverse

    450

    ...

    395

    ...

    ...

    3

    2124

    T851E

     

     

    short transverse

    435

    ...

    380

    ...

    ...

    1

    2124

    T851E

     80.00

    100.00

    longitudinal

    450

    ...

    385

    ...

    ...

    4

    2124

    T851E

     

     

    long transverse

    450

    ...

    385

    ...

    ...

    3

    2124

    T851E

     

     

    short transverse

    425

    ...

    370

    ...

    ...

    1

    2124

    T851E

    100.00

    130.00

    longitudinal

    440

    ...

    380

    ...

    ...

    4

    2124

    T851E

     

     

    long transverse

    440

    ...

    380

    ...

    ...

    3

    2124

    T851E

     

     

    short transverse

    420

    ...

    365

    ...

    ...

    1

    2124

    T851E

    130.00

    150.00

    longitudinal

    435

    ...

    370

    ...

    ...

    4

    2124

    T851E

     

     

    long transverse

    435

    ...

    370

    ...

    ...

    3

    2124

    T851E

     

     

    short transverse

    400

    ...

    350

    ...

    ...

    1

     

    Alloy

    Temper

    Specified Thickness,
    mm

    Tensile Strength,
    MPa

    Yield Strength
    (0.2 % offset), MPa

    Elongation,C
    min, %

    over

    through

    min

    max

    min

    max

    B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate

    B548 Test Method for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels

    B557M Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)

    B594 Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products for Aerospace Applications

    B632/B632M Specification for Aluminum-Alloy Rolled Tread Plate

    B660 Practices for Packaging/Packing of Aluminum and Magnesium Products

    B666/B666M Practice for Identification Marking of Aluminum and Magnesium Products

    B881 Terminology Relating to Aluminum- and Magnesium-Alloy Products

    B918 Practice for Heat Treatment of Wrought Aluminum Alloys

    B928/B928M Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service and Similar Environments

    B947 Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys

    E290 Test Methods for Bend Testing of Material for Ductility

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    E607 Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere

    E716 Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spectrochemical Analysis

    E1004 Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method

    E1251 Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry

    G34 Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test)

    G47 Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products

    ISO Standards

    ISO6361-2 Wrought Aluminum and Aluminum Alloys, Sheets, Strips, and Plates


    ICS Code

    ICS Number Code 77.120.10 (Aluminium and aluminium alloys)

    UNSPSC Code

    UNSPSC Code 30102206(Aluminum plate); 30265000(Aluminum sheets)


    Referencing This Standard

    DOI: 10.1520/B0209M-14

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM B209M-14, Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric), ASTM International, West Conshohocken, PA, 2014, www.astm.org

    Back to Top