ASTM A928 / A928M - 13

    Standard Specification for Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with Addition of Filler Metal

    Active Standard ASTM A928 / A928M | Developed by Subcommittee: A01.10

    Book of Standards Volume: 01.01


      Format Pages Price  
    PDF 7 $42.00   ADD TO CART
    Hardcopy (shipping and handling) 7 $42.00   ADD TO CART
    Standard + Redline PDF Bundle 14 $50.40   ADD TO CART


    Abstract

    This specification covers standard requirements for ferritic/austenitic (duplex) stainless steel pipe that is electric fusion welded with addition of filler metal suitable for corrosive service. Heat treatment shall be performed after welding and in accordance with specified temperature and quench conditions. Several grades of ferritic/austenitic steel shall conform to the requirements of the applicable specification and grade designation. Heat and product analyses shall be conducted and shall conform to the requirements for the particular grade. The plate used in making the pipe shall conform to the required tensile properties. The steel pipe shall undergo several mechanical tests including transverse tension test, transverse guided-bend test, nondestructive test, hydrostatic test, and nondestructive electric test.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers electric-fusion-welded steel pipe suitable for corrosive service.

    Note 1The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for traditional terms such as nominal diameter, size, and nominal size.

    1.2 This specification covers grades of ferritic/austenitic steel as indicated in Table 1. The selection of the proper alloy and requirements for heat treatment shall be at the discretion of the purchaser, dependent on the service conditions to be encountered.

    1.3 Five classes of pipe are covered as follows:

    1.3.1 Class 1—Pipe shall be double welded by processes using filler metal in all passes and shall be radiographed completely.

    1.3.2 Class 2—Pipe shall be double welded by processes using filler metal in all passes. No radiograph is required.

    1.3.3 Class 3—Pipe shall be single welded by processes using filler metal in all passes and shall be radiographed completely.

    1.3.4 Class 4—Same as Class 3, except that the weld pass exposed to the inside pipe surface is permitted to be made without the addition of filler metal (see 6.2.2.1 and 6.2.2.2).

    1.3.5 Class 5—Pipe shall be double welded by processes using filler metal in all passes and shall be spot radiographed.

    1.4 Supplementary requirements covering provisions ranging from additional testing to formalized procedures for manufacturing practice are provided. Supplementary Requirements S1 through S4 are included as options to be specified in the purchase order when desired.

    1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the M designation of the specification is specified in the order.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

    A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe

    E426 Practice for Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Titanium, Austenitic Stainless Steel and Similar Alloys


    ICS Code

    ICS Number Code 25.160.40 (Welding joints and welds)

    UNSPSC Code

    UNSPSC Code 31311509(Stainless steel welded or brazed pipe assemblies)


    DOI: 10.1520/A0928_A0928M

    ASTM International is a member of CrossRef.

    ASTM A928 / A928M

    Citing ASTM Standards
    Back to Top