Abstract
This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. The pipe and fittings shall be iron castings suitable for installation and service for sanitary, storm drain, waste, and vent piping applications. The pipe and fittings shall meet all applicable requirements and tests given in this specification. Tensile test and chemical test shall be made to conform to the requirements specified. The pipe and fittings shall be uniformly coated with a material suitable for the purpose that is adherent, not brittle, and without a tendency to scale.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. 1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification. 1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification. 1.3.1 Lengths: | | Figures | | EDP/ASA Identification Numbers
for Hubless Pipe | Fig. 1 | | 10 ft (3.0 m) in sizes and 5 ft. (1.5 m)
11/2 , 2, 3, 4, 5, 6, 8,
10, 12, and 15 in. | Fig. 1, Fig. 2 | | Method of Specifying Fittings | Fig. 3 | 1.3.2 Fittings: | Quarter Bend | Fig. 5 | | Quarter Bend, Reducing | Fig. 6 | | Quarter Bend, With Side Opening | Fig. 7 | | Quarter Bend, With Heel Opening | Fig. 8 | | Quarter Bend, Tapped | Fig. 9 | | Quarter Bend, Double | Fig. 10 | | Quarter Bend, Long | Fig. 11 | | Short Sweep | Fig. 12 | | Long Sweep | Fig. 13 | | Long Sweep, Reducing | Fig. 14 | | Fifth Bend | Fig. 15 | | Sixth Bend | Fig. 16 | | Eighth Bend | Fig. 17 | | Eighth Bend Long | Fig. 18 | | Sixteenth Bend | Fig. 19 | | Sanitary Tee | Fig. 20 | | Sanitary Tee With Side Opening | Fig. 21 | | Sanitary Tee With 2 in. Side Opening R or L/R and L | Fig. 22 | | Sanitary Tee, New Orleans Special With Side Opening | Fig. 23 | | Sanitary Tee With 45° Side Openings and New Orleans | Fig. 24 | | Sanitary Special Tee Tapped | Fig. 25 | | Sanitary Tapped Tee, Horizontal Twin | Fig. 26 | | Sanitary Tapped Tee, Double Vertical | Fig. 27 | | Y Branch | Fig. 28 | | Y Branch, Double | Fig. 29 | | Y Branch, Upright | Fig. 30 | | Upright Y Wide Center Florida Special | Fig. 31 | | Y Branch, Combination 1/8 Bend | Fig. 32 | | Y Branch, Combination 1/8 Bend Double | Fig. 33 | | Sanitary Cross | Fig. 34 | | Sanitary Cross With Side Opening | Fig. 35 | | Sanitary Cross, New Orleans, With Side Openings | Fig. 36 | | Sanitary Cross, New Orleans, With 45° Special and
Regular Side Openings | Fig. 37 | | Sanitary Cross, Tapped | Fig. 38 | | Test Tee | Fig. 39 | | Tapped, Extension Piece | Fig. 40 | | Increaser-Reducer | Fig. 41 | | Increaser-Reducer, Short | Fig. 42 | | Tapped Adapter | Fig. 43 | | Blind Plug | Fig. 44 | | Iron Body Cleanout-Tapped | Fig. 45 | | P Trap | Fig. 46 | | P Trap, Long | Fig. 47 | | P Trap, Deep Seal | Fig. 48 | | P Trap, With Primer | Fig. 49 | | P Trap, With Tapped Inlet | Fig. 50 | | Tapped Inlet, Double | Fig. 51 | | Modified Combination Wye and 1/8 Bend, Double | Fig. 52 | | Modified Combination Wye and 1/8 Bend, Double, Extended | Fig. 53 | | Two-Way Cleanout | Fig. 54 | | Twin Cleanout | Fig. 55 | | Closet Bend, Regular and Reducing | Fig. 56 | | Closet Flange Riser | Fig. 57 | | Tapping Bosses | Fig. 58 | | Double Sweep Sanitary Tee (Extended) | Fig. 59 | | Running Trap with Double Vents | Fig. 60 | | P Trap with Tapped or Hubless Side Inlet | Fig. 61 | | Vented Tub Wye Extended, Double | Fig. 62 | | Vented Tub Wye Extended Offset, Left or Right | Fig. 63 | | Vented Tub Wye | Fig. 64 | | Double Two Way Cleanout | Fig. 65 | 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301. Note 1— The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
2. Referenced Documents (purchase separately)  The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A48/A48M Specification for Gray Iron Castings
A644 Terminology Relating to Iron Castings
D1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
E8 Test Methods for Tension Testing of Metallic Materials
E1645 Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis
E2349 Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing
Federal Standard
Fed.Std.No.123 Marking for Shipment (Civil Agencies)
Military Standard
MIL-STD-129 Military Marking for Shipment and Storage
ANSI/ASME Standard
B1.20 Pipe Threads
Other Documents
CastIronSoilPipeInst Specification 301 Available from Cast Iron Soil Pipe Institute (CISPI), 5959 Shallowford Rd., Suite 419, Chattanooga, TN 37421, http://www.cispi.org.
Keywords
cast iron; hubless pipe and fittings; no-hub pipe and fittings; soil pipe;
ICS Code
ICS Number Code 23.040.01 (Pipeline components in general. Pipelines); 91.140.80 (Drainage systems)
DOI: 10.1520/A0888-13
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
|
