This specification covers post-applied coatings, pavings, and linings for corrugated steel pipe and corrugated steel structural plate pipe, pipe-arches, and arches coated, paved, or lined with specified materials over either metallic coatings or metallic coatings with polymer coatings. Asphalt, polymerized asphalt, polymer, mastic, and emulsion coatings and asphalt and concrete pavements and linings are included. Two-step classification procedure is used to describe post-applied coatings, pavings, and linings. The first classification is based on the type of coating, paving, or lining material to be used. The second is a coating, paving, and lining type giving the physical location of the coating or lining on the pipe.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers post-applied coatings, pavings, and linings for corrugated steel pipe and corrugated steel structural plate pipe, pipe-arches, and arches coated, paved, or lined with specified materials over either metallic coatings or metallic coatings with polymer coatings. This specification includes asphalt, polymerized asphalt, polymer, mastic, and emulsion coatings and asphalt and concrete pavements and linings applied to the pipe in the producing plant, as well as, asphalt and mastic coatings applied in the field. Field-applied concrete pavements and linings are covered by Specification A979/A979M. The pipe to which the coatings are applied is described in Specifications A760/A760M, A761/A761M, and A762/A762M.
1.2 There is no cleaning operation currently included in pipe coating practice. However, experience has shown that a clean substrate provides good adherence for both cold- and hot-applied post coatings. The performance of post coating or lining, or both, will depend on the surface cleanliness over which it is applied.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in brackets are for information only.
1.4 The following safety hazards caveat pertains only to the test methods portions, Sections 11 and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A742/A742M Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe
A760/A760M Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains
A761/A761M Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches
A762/A762M Specification for Corrugated Steel Pipe, Polymer Precoated for Sewers and Drains
A862/A862M Practice for Application of Asphalt Coatings to Corrugated Steel Sewer and Drainage Pipe
A926 Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe
A979/A979M Specification for Concrete Pavements and Linings Installed in Corrugated Steel Structures in the Field
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C33 Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C150 Specification for Portland Cement
C309 Specification for Liquid Membrane-Forming Compounds for Curing Concrete
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
D5 Test Method for Penetration of Bituminous Materials
D6 Test Method for Loss on Heating of Oil and Asphaltic Compounds
D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
D70 Test Method for Density of Semi-Solid Bituminous Materials (Pycnometer Method)
D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester
D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
D1187 Specification for Asphalt-Base Emulsions for Use as Protective Coatings for Metal
D2042 Test Method for Solubility of Asphalt Materials in Trichloroethylene
D4402 Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer
asphalt-coated steel pipe; coatingscorrugated steel pipe; corrugated steel sewer/drain pipe; drainage systemsewer/drainage pipe (steel); liningscorrugated steel pipe; pavingscorrugated steel pipe; pipe coatings; pipe line coatings/linings/paving; pipe linings; pipe paving; steel pipe coatings/linings/paving; steel pipe/corrugated steel; Drainage materials/systems--specifications; Fabricated materials--specifications; Corrugated steel sewer/drain pipe--specifications; Liner/linings--specifications; Metallic-coated steel pipe--specifications; Bituminous coatings--specifications; Pipeline coatings--specifications; Polymer coatings--steel; Post-applied coatings/pavings/linings; Sewer pipe (steel)--specifications; Steel pipe--specifications; Steel plate pipe--specifications; Structural steel (SS) pipe--specifications; Structural steel (SS) plate--specifications;
ICS Number Code 23.040.10 (Iron and steel pipes)
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]