ASTM A792 / A792M - 10

    Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process

    Active Standard ASTM A792 / A792M | Developed by Subcommittee: A05.11

    Book of Standards Volume: 01.06


      Format Pages Price  
    PDF 6 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 6 $43.00   ADD TO CART
    Standard + Redline PDF Bundle 12 $51.60   ADD TO CART


    Abstract

    This specification covers 55% aluminum-zinc alloy-coated steel sheets in coils and cut lengths for applications requiring corrosion resistance or heat resistance or both. The material is available in several designations: commercial steel, forming steel, drawing steel, high temperature steel, and structural steel. Heat analysis shall be performed wherein the steel materials shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, aluminum, copper, nickel, chromium, molybdenum, vanadium, columbium, titanium, nitrogen and boron. Mechanical tests shall be performed wherein the steel sheets shall conform to the required values of yield strength, tensile strength and elongation. Triple-spot tests and single-spot tests shall also be performed and the materials shall conform to the required values of coating weight/mass. Steel specimens shall also undergo coating bend tests and shall conform to the required ratio of the inside bend diameter to thickness.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers 55 % aluminum-zinc alloy-coated steel sheet in coils and cut lengths.

    1.2 This product is intended for applications requiring corrosion resistance or heat resistance, or both.

    1.3 The product is produced in a number of designations, types, and grades which are designed to be compatible with differing application requirements.

    1.4 Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M, unless otherwise provided herein.

    1.5 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.

    1.6 This specification is applicable to orders in either inch-pound units (as A792) or SI units (as A792M). Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independent of the other.

    1.7 Unless the order specifies the M designation (SI units), the product shall be furnished to inch-pound units.

    1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings

    A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for

    A902 Terminology Relating to Metallic Coated Steel Products

    A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process

    E517 Test Method for Plastic Strain Ratio r for Sheet Metal

    E646 Test Method for Tensile Strain-Hardening Exponents (n -Values) of Metallic Sheet Materials


    ICS Code

    ICS Number Code 77.140.50 (Flat steel products and semi-products)

    UNSPSC Code

    UNSPSC Code 30264000(Carbon steel sheets)


    Referencing This Standard

    DOI: 10.1520/A0792_A0792M-10

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM A792 / A792M-10, Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process, ASTM International, West Conshohocken, PA, 2010, www.astm.org

    Back to Top