ASTM A707 / A707M - 13

    Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service

    Active Standard ASTM A707 / A707M | Developed by Subcommittee: A01.22

    Book of Standards Volume: 01.01


      Format Pages Price  
    PDF 6 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 6 $43.00   ADD TO CART
    Standard + Redline PDF Bundle 12 $51.60   ADD TO CART


    Abstract

    This specification covers forged carbon and alloy steel flanges intended primarily for petroleum and gas pipelines in areas subject to low ambient temperatures. Eight grades, four yield-strength classes, and three different notch toughness levels are included. All material shall be heat treated by annealing, normalizing, precipitation hardening, quenching-and-tempering, normalizing-and-tempering, normalizing-and-precipitation hardening, or quenching-and-precipitation hardening. A chemical heat analysis shall be made and conform to the requirements as to chemical composition specified. The material in the weld neck shall conform to the mechanical property requirements specified. Hardness test, impact test, ultrasonic test, tension test, and hydrostatic test shall be made to conform to the specified requirements.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers forged carbon and alloy steel flanges intended primarily for petroleum and gas pipelines in areas subject to low ambient temperatures. Included are flanges to specified dimensions or to dimensional standards such as those MSS, ASME, and API specifications that are referenced in Section 2.

    1.2 Supplementary requirements are provided for use when additional requirements are desired. These shall apply only when specified individually by the purchaser in the order.

    1.3 Eight grades, four yield-strength classes, and three different notch toughness levels are included.

    1.4 The availability of a particular size of flange of a specific grade and class is limited only by the capability of the composition to meet the specified mechanical property requirements. However, current practice normally limits the following:

    (a) Grade L1 to Classes 1 and 2,
    (b) Grade L2 to Classes 1, 2, and 3,
    (c) Grade L3 to Classes 1, 2, and 3,
    (d) Grade L4 to Classes 1, 2, and 3,
    (e) Grade L7 to Classes 1 and 2, and
    (f) Grades L5, L6, and L8 are generally available in any class.

    1.5 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

    1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A388/A388M Practice for Ultrasonic Examination of Steel Forgings

    A788/A788M Specification for Steel Forgings, General Requirements

    A961/A961M Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications

    API Standard

    605 Large Diameter Carbon Steel Flanges Available from American Petroleum Institute (API), 1220 L. St., NW, Washington, DC 20005-4070, http://api-ec.api.org.

    ASME Boiler and Pressure Vessel Code

    SectionIX Welding Qualifications

    SectionVIII Division I, Part UG-84 Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.

    ASME Standard

    B 16.5 Dimensional Standards for Steel Pipe Flanges and Flanged Fittings

    AWS Standards

    A 5.5 Low-Alloy Steel Covered Arc-Welding Electrodes Available from American Welding Society (AWS), 550 NW LeJeune Rd., Miami, FL 33126, http://www.aws.org.


    ICS Code

    ICS Number Code 23.040.60 (Flanges, couplings and joints)

    UNSPSC Code

    UNSPSC Code 40170000(Pipe piping and pipe fittings)


    DOI: 10.1520/A0707_A0707M

    ASTM International is a member of CrossRef.

    ASTM A707 / A707M

    Citing ASTM Standards
    Back to Top