You are being redirected because this document is part of your ASTM Compass® subscription.
    This document is part of your ASTM Compass® subscription.

    ASTM A682/A682M-05

    Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled, General Requirements For (Withdrawn 2009)

    Withdrawn Standard: ASTM A682/A682M-05 | Developed by Subcommittee: A01.19

    WITHDRAWN, REPLACED BY A684/A684M


      Format Pages Price  
    PDF 8 $54.00   ADD TO CART

    Active (view current version of standard)

    ASTM License Agreement


    Withdrawn Rationale:

    This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths.

    Formerly under the jurisdiction of Committee A01 on Steel, Stainless Steel and Related Alloys, this specification was withdrawn in October 2009 and replaced by Specification A684/A684M for Steel, Strip, High-Carbon, Cold-Rolled.

    1. Scope

    1.1 This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. (7.6 mm) or less in thickness and over 1/2 to 23 15/16 in. (12.5 to 600 mm) in width, inclusive. Strip tolerance products may be available in widths wider than 2315/16 in. (600 mm) by agreement between purchaser and supplier; however, such products are technically classified as cold-rolled sheet.

    1.2 The maximum of the specified carbon range is over 0.25 % to 1.35 %, inclusive.

    1.3 The above shall apply to the cold-rolled carbon spring steel strip furnished under each of the following specifications issued by ASTM:

    Title of SpecificationASTMDesignationSteel, Strip, High Carbon,Cold Rolled A 684/A 684M

    1.4 The tolerances in this specification are different than those in Specification A 568/A 568M and Specification A 109/A 109M.

    1.5 For the purpose of determining conformance with this specification, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.

    1.6 The metric portions of the tables herein list permissible variations in dimensions and mass (see Note 0) in SI (metric) units. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. Conformance to SI tolerances is mandatory when the "M" specification is used.

    Note 1—The term weight is used when inch-pound units are the standard. However, under SI the preferred term in mass.

    1.7 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems will result in nonconformance with the specification.

    1.8 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.



    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A684/A684M Specification for Steel, Strip, High-Carbon, Cold-Rolled

    A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Domestic Shipment

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E527 Practice for Numbering Metals and Alloys (UNS)

    Federal Standards

    Fed. Std. No. 183 Continuous Identification Marking of Iron and Steel Products

    Military Standards

    MIL-STD-163 Steel Mill Products Preparation for Shipment and Storage

    SAE Standard

    J1086 Recommended Practice for Numbering Metals and Alloys (UNS)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A0682_A0682M-05

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM A682 / A682M-05, Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled, General Requirements For (Withdrawn 2009), ASTM International, West Conshohocken, PA, 2005, www.astm.org

    Back to Top