Abstract
This specification covers laser-fused stainless steel bars, plates, and shapes of structural quality for use in bolted or welded structural applications. The butt-welded test pieces are welded using laser fusion and then machined into tensile test bars and root-bend test specimens. The term laser fusion is used in this specification to refer to a joining process that is able to produce a coalescence of material using the heat obtained from the application of a concentrated coherent light beam impinging on the surface of a weld joint.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers laser-fused stainless steel bars, plates, and shapes of structural quality for use in bolted or welded structural applications.
1.2 Shapes covered in this specification include those classified in Article 3.1.2 of Specification A6/A6M and those that are made from two or more shapes or plates.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) 
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A276 Specification for Stainless Steel Bars and Shapes
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A479/A479M Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
A673/A673M Specification for Sampling Procedure for Impact Testing of Structural Steel
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A923 Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
E190 Test Method for Guided Bend Test for Ductility of Welds
E208 Test Method for Conducting Drop-Weight Test to Determine Nil-Ductility Transition Temperature of Ferritic Steels
E290 Test Methods for Bend Testing of Material for Ductility
ISO Standards
ISO15614-11 Specification and qualification of welding procedures for metallic materials- Welding procedure test-Part 11: Electron and laser beam welding.
U.S. Military Standards
MIL-STD-129 Marking for shipment and storage.
Federal Standards
FederalStandardNo.12 Marking for Shipment (Civil Agencies).
Keywords
joining; laser-fusion; laser-weld; plates; shapes; stainless;
ICS Code
ICS Number Code 77.140.60 (Steel bars and rods)
DOI: 10.1520/A1069_A1069M-11
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
