ASTM A1053 / A1053M - 12e1

    Standard Specification for Welded Ferritic-Martensitic Stainless Steel Pipe

    Active Standard ASTM A1053 / A1053M | Developed by Subcommittee: A01.10

    Book of Standards Volume: 01.01


      Format Pages Price  
    PDF Version 4 $37.00   ADD TO CART
    Print Version 4 $37.00   ADD TO CART


    Abstract

    This specification covers seam welded ferritic-martensitic stainless steel pipe intended for abrasive and general corrosion service. The pipes are classified according to sizes, from NPS 2 to NPS 36. The pipe shall be made using Electric Resistance Welding (ERW) or an automatic fusion welding process with no addition of filler metal during the welding process. All pipes shall be made from heat treated strip or plate, cold formed and welded. Tensile test, flattening test, hydrostatic test, and nondestructive electric test shall be made in accordance with the pipe specification to conform to the requirements specified.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers seam welded ferritic-martensitic (dual phase) stainless steel pipe intended for abrasive and general corrosion service, manufactured with or without the addition of filler metal. Nominal sizes are NPS 2 to NPS 36 inclusive, with nominal (average) wall thickness up to 0.75-in. (19 mm).

    1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents. Therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation is specified in the order.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    Other Standard

    SAE J1086 Practice for Numbering Metals and Alloys (UNS) Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.

    ANSI/ASME Standards

    ASME Boiler and Pres Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.

    B1.20.1 Pipe Threads, General Purpose

    B36.10 Welded and Seamless Wrought Steel Pipe

    B36.19 Stainless Steel Pipe

    ASTM Standards

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe

    A1010/A1010M Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip

    A1016/A1016M Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)


    ICS Code

    ICS Number Code 23.040.10 (Iron and steel pipes)

    UNSPSC Code

    UNSPSC Code 40171621(Industrial welded stainless steel pipe)


    DOI: 10.1520/A1053_A1053M

    ASTM International is a member of CrossRef.

    ASTM A1053 / A1053M

    Citing ASTM Standards
    Back to Top