ASTM A1019/A1019M-01(2007)

    Standard Specification for Closed Rib Steel Pipe with Diameter of 36 in. [900 mm] or Less, Polymer Precoated for Sewers and Drains (Withdrawn 2012)

    Withdrawn Standard: ASTM A1019/A1019M-01(2007) | Developed by Subcommittee: A05.17

    WITHDRAWN, NO REPLACEMENT


      Format Pages Price  
    PDF Version 6 $50.40   ADD TO CART


    Withdrawn Rationale:

    This specification covers polymer precoated, closed rib steel pipe, intended for use for storm water drainage, under-drains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes. The steel sheet used in fabrication of the pipe has a polymer protective coating over a metallic coating of zinc.

    1. Scope

    1.1 This specification covers polymer precoated, closed rib steel pipe, intended for use for storm water drainage, under-drains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes. The steel sheet used in fabrication of the pipe has a polymer protective coating over a metallic coating of zinc.

    1.2 The polymer precoating provides extra protection of the base metal against corrosion or abrasion, or both, in addition to that provided by the metallic coating. Severe environments are likely to cause corrosion problems to accessory items such as coupling band hardware that does not have a polymer coating unless supplemental protection is provided. Additional protection for polymer precoated steel pipe is available by use of coatings applied after fabrication of the pipe as described in Specification A 849.

    1.3 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and sheet thickness of the pipe. Experience with drainage products has shown that successful performance depends upon the proper selection of rib depth, sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in installation. The installation procedure is described in Practice A 798/A 798M.

    1.4 This specification is applicable to orders in either inch-pound units as A 1019, or in SI units as A 1019M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values when the material is ordered to A 1019M.

    This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.



    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings

    A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

    A307 Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength

    A563 Specification for Carbon and Alloy Steel Nuts

    A563M Specification for Carbon and Alloy Steel Nuts (Metric)

    A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

    A742/A742M Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe

    A780 Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings

    A796/A796M Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewers and Other Buried Applications

    A798/A798M Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other Applications

    A849 Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe

    A902 Terminology Relating to Metallic Coated Steel Products

    A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process

    B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel

    B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    C443 Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

    D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers

    D1056 Specification for Flexible Cellular Materials--Sponge or Expanded Rubber ,

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric)

    AASHTO Standard

    T249M Test for Helical Lock Seam Corrugated Pipe


    DOI: 10.1520/A1019_A1019M-01R07

    ASTM International is a member of CrossRef.