ASTM A1006 / A1006M - 00(2010)

    Standard Specification for Steel Line Pipe, Black, Plain End, Laser Beam Welded

    Active Standard ASTM A1006 / A1006M | Developed by Subcommittee: A01.09

    Book of Standards Volume: 01.01


    Buy Standard (PDF)
    6 pages
    $42.00
    Buy Standard (Print)
    6 pages
    $42.00

    Historical (view previous versions of standard)


    ASTM A1006 / A1006M

    Abstract

    This specification covers the standard requirements for laser beam welded, black plain end steel pipe for use in the conveyance of fluids under pressure. Dimensions and weight [mass] per unit length of pipes with designated NPS sizes and specified nominal wall thickness shall be given. Heat and product analysis shall be performed wherein steel shall conform to the required chemical composition for carbon, sulfur, and phosphorus. The steel shall conform to the required tensile properties such as minimum and maximum yield strength. The following tests shall be conducted, namely: Charpy V-notch test; weld ductility test; and hydrostatic test.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers laser beam welded, black, plain end steel pipe for use in the conveyance of fluids under pressure. Pipe in sizes NPS 1 to 26, inclusive, with nominal wall thickness 0.750 in. [19.1 mm] or less, as given in Table 1, is included. Pipe having other dimensions, in this size range, may be furnished provided such pipe complies with all other requirements of this specification.

    1.2 It is intended that the pipe be capable of being circumferentially welded in the field when welding procedures in accordance with the requirements of the applicable pipeline construction code are used.

    1.3 The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values in each system are not exact equivalents: therefore, each system is to be used independently of the other, without combining values in any way.

    1.4 The following precautionary statement pertains to the test method portion, Section 14, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A450/A450M Specification for General Requirements for Carbon and Low Alloy Steel Tubes

    A530/A530M Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    API Publication

    APIRP5L3 Recommended Practice for Conducting Drop-Weight Tear Tests on Line Pipe Available from American Petroleum Institute (API), 1220 L. St., NW, Washington, DC 20005-4070, http://www.api.org.

    ASME Standard

    ASMEBoilerandPressur , Welding and Brazing Qualifications Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.


    ICS Code

    ICS Number Code 77.140.75 (Steel pipes and tubes for specific use); 23.040.10 (Iron and steel pipes)

    UNSPSC Code

    UNSPSC Code 78102100(Pipeline services)


    DOI: 10.1520/A1006_A1006M-00R10

    ASTM International is a member of CrossRef.

    ASTM A1006 / A1006M

    Citing ASTM Standards
    Back to Top