Motor Gasoline

    2014 Annual Fee: $759.00

    Schedule: April, August, December

    Sample amount distributed each test cycle: Approximately 1 gallon



    ABOUT THE PROGRAM

    ASTM’s Motor Gasoline Proficiency Testing Program provides laboratories with a statistical quality assurance (SQA) tool, enabling them to compare, improve, and maintain, a high level of performance in the use of ASTM methods with other laboratories worldwide.

    Conducted three times annually, this program provides a different commercial sample, electronic report forms, and test instructions for each test cycle. Your laboratory performs the tests that you normally conduct within your own facility using the specified ASTM methods cited in the program.

    Samples, test instructions and data report forms are distributed electronically to each participant on the date samples are distributed. Labs have approximately 8 weeks to submit test data with the final statistical summary reports being electronically distributed in approximately 25 business days.

    For more information, contact us.


    WHY SHOULD YOUR LABORATORY PARTICIPATE?

    ASTM's Proficiency Test Program provides you with:

    • A useful and meaningful statistical quality assurance tool to monitor the strengths and weaknesses of your laboratory's performance in conducting testing.
    • The resource you need to satisfy proficiency testing elements of laboratory accreditation.
    • A periodic comparison of test results with other participating laboratories.

    TEST MATERIALS

    One gallon of motor gasoline will be used in the program for each test cycle.


    TEST PARAMETERS

    D3227

    Mercaptan Sulfur

    D4815

    Alcohol

    D3606, D4053, D5580, D5769

    Benzene, Toluene, C9 Plus Aromatics

    D130

    Copper Corrosion

    D1298, D4052

    Density

    D86, D7096

    Distillation

    D381

    Gum

    D1319, D6839

    Hydrocarbon Type

    D3237

    Lead Content

    D525

    Oxidation Stabilty

    D5599, D5845

    Oxygenates

    D3231

    Phosphorus Content

    D2622, D4294, D5453, D7039

    Sulfur Content

    D5188

    Vapor/Liquid Ratio

    D5191

    Vapor Pressure

    NOTE: List of tests subject to change.


    DISTRIBUTION OF SAMPLES

    Test samples are prepared and distributed for ASTM International by Clark Labs in Jefferson Hills, PA. Program registration fees include the cost of shipping the test samples to U.S. participants or, for international participants, to a third-party shipping agent located in the U.S.

    IMPORTANT for International participants: You have the following options for receipt of samples:

    • Ship through a third party shipping agent - Provide ASTM International with the complete contact information of a designated Shipping Agent located in the U.S. who will be responsible for shipping samples from the U.S. to your facility. Participants are responsible for making financial and shipping arrangements directly with the shipping agent.
      • Please be advised that when samples are shipped, an e-mail is sent only to the contact of record on your ASTM PTP account. It is the customer’s responsibility to advise their designated shipper that the sample has been shipped.
      • We cannot permit shipping agents to pick up samples at our distributors’ warehouses.
    • Ship directly from the sample distributor via UPS, DHL, or FEDEX - Provide ASTM International with your shipping account number to cover shipping charges. Check that your carrier will deliver the test materials to your location. Materials classified as Hazardous may have restrictions.

    PROGRAM REQUIREMENTS

    Participation is on an annual fee basis and open to all laboratories. Registration fees must be paid in advance to participate. Testing must be performed within the participant's laboratory facilities. A laboratory does not need to perform all the program tests to participate.


    ABOUT ASTM INTERNATIONAL COMMITTEE D02 ON PETROLEUM PRODUCTS AND LUBRICANTS

    Committee D02 on Petroleum Products and Lubricants, consisting of over 1,500 members and developer of nearly 670 ASTM International standards, provides the technical direction for the program. Test information generated through the program is utilized by Committee D02 to determine if modifications to ASTM International methods or new methods are warranted and to analytically review program test results. (All data and related information generated from the program is coded to maintain lab confidentiality.)