Society
Review of Main Committee Ballot Actions
March
2010
Deadline
for Receipt: Must be Received Before April 1, 2009
The
items listed are currently being balloted by the
corresponding main committee and are submitted here for review. To request
copies of proposed new standards and revisions of standards for review and
voting purposes only, please email socrev@astm.org and provide the following
information:
-
Your name
- Your member number
- The designation and title of the main committee of interest (e.g., A04 on
Iron Castings)
- The designation of the ballot (e.g., #00-01)
- The specific item(s) (e.g., Item 22)
After
receiving the items you’ve requested, if you would like to comment or vote
negative you may submit additional correspondence to ASTM Headquarters. All
comments and negatives submitted by Society members will be considered by the
originating subcommittee and main committee.
Key:
(#00-01) = Ballot Designation #
(Sub.00) = Subcommittee Jurisdiction
(CC) = Item is being balloted concurrently by the subcommittee and main
committee
(Ref. Z6287Z) = reference # for new standards that have not yet been approved
A01 on Steel, Stainless
Steel and Related Alloys (#10-01)
NEW
STANDARD
New
Standard, Specification for Zinc-coated (galvanized) Steel Welded Wire
Reinforcement, Plain and Deformed, for Concrete (Item
11) (Sub .05) (CC) (Ref. Z2973Z)
New
Standard, Specification for High-strength Loy-alloy Structural Steel Plate
Produced by Thermo-mechanical Controll Process (tmcp)
(Item 5) (Sub .02) (Ref. WK19921 )
REVISION
OF STANDARD
A
6/A 6M-2009, Specification for General Requirements for Rolled Structural Steel
Bars, Plates, Shapes, and Sheet Piling
(Item 1) (Sub .02) (CC)
A
193/A 193M-2009, (Includes Change to Title) Specification for Alloy-steel and
Stainless Steel Bolting Materials for High Temperature or High Pressure Service
and Other Special Purpose Applications
(Item 81) (Sub .22) (CC)
A
194/A 194M-2009, Specification for Carbon and Alloy Steel Nuts for Bolts for
High Pressure or High Temperature Service, or Both (Item
82) (Sub .22) (CC)
A
213/A 213M-2009b, Specification for Seamless Ferritic
and Austenitic Alloy-steel Boiler, Superheater, and
Heat-exchanger Tubes (Items
31,32,33,34,35) (Sub .10)
A
240/A 240M-2009c, Specification for Chromium and Chromium-nickel Stainless
Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications (Items
51,52,53) (Sub .17) (CC)
A
249/A 249M-2008, Specification for Welded Austenitic Steel Boiler, Superheater, Heat-exchanger, and Condenser Tubes (Items 36,37) (Sub .10)
A
262-2002A(2008), Practices for Detecting
Susceptibility to Intergranular Attack in Austenitic
Stainless Steels (Item 49) (Sub .14) (CC)
A
268/A 268M-2005a, Specification for Seamless and Welded Ferritic
and Martensitic Stainless Steel Tubing for General
Service (Item 38) (Sub .10)
A
269-2008, Specification for Seamless and Welded Austenitic Stainless Steel
Tubing for General Service
(Item 39) (Sub .10)
A
270-2003B(2008)E01, Specification for Seamless and
Welded Austenitic and Ferritic/austenitic Stainless
Steel Sanitary Tubing (Item 40) (Sub .10)
A
313/A 313M-2008, Specification for Stainless Steel Spring Wire (Item
54) (Sub .17)
A
320/A 320M-2008, (Includes Change to Title) Specification for Alloy-steel and
Stainless Steel Bolting Materials for Low-temperature Service (Item
83) (Sub .22) (CC)
A
333/A 333M-2005, Specification for Seamless and Welded Steel Pipe for
Low-temperature Service
(Item 41) (Sub .10)
A
335/A 335M-2009a, Specification for Seamless Ferritic
Alloy-steel Pipe for High-temperature Service (Items 43,44) (Sub .10)
A
351/A 351M-2006, Specification for Castings, Austenitic, for
Pressure-containing Parts
(Item 59) (Sub .18)
A
370-2009AE01, Test Methods and Definitions for Mechanical Testing of Steel Products (Item 46) (Sub .13)
A
388/A 388M-2009, Practice for Ultrasonic Examination of Steel Forgings (Item 14) (Sub .06)
A
414/A 414M-2009, Specification for Steel, Sheet, Carbon, for Pressure Vessels (Items 75,76)
(Sub .19)
A
416/A 416M-2006, Specification for Steel Strand, Uncoated Seven-wire for Prestressed Concrete
(Items 6,7) (Sub .05)
A
427-2002(2007), Specification for Wrought Alloy Steel Rolls for Cold and Hot Reduction (Item 15) (Sub .06)
A
437/A 437M-2006, (Includes Change to Title) Specification for Alloy-steel
Turbine-type Bolting Material Specially Heat Treated for High-temperature Service (Item 84) (Sub .22) (CC)
A
453/A 453M-2008, Specification for High-temperature Bolting Materials, with
Expansion Coefficients Comparable to Austenitic Stainless Steels (Items 85,86) (Sub .22) (CC)
A
479/A 479M-2009, Specification for Stainless Steel Bars and Shapes for Use in
Boilers and Other Pressure Vessels
(Item 55) (Sub .17)
A
480/A 480M-2009b, Specification for General Requirements for Flat-rolled
Stainless and Heat-resisting Steel Plate, Sheet, and Strip (Item
56) (Sub .17) (CC)
A
488/A 488M-2009, Practice for Steel Castings, Welding, Qualifications of
Procedures and Personnel
(Item 62) (Sub .18) (CC)
A
500/A 500M-2009, Specification for Cold-formed Welded and Seamless Carbon Steel
Structural Tubing in Rounds and Shapes (Item
23) (Sub .09)
A
507-2006, Specification for Drawing Alloy Steel, Sheet and Strip, Hot-rolled
and Cold-rolled (Item 77) (Sub .19) (CC)
A
540/A 540M-2006, (Includes Change to Title) Specification for Alloy-steel
Bolting Materials for Special Applications (Item
87) (Sub .22) (CC)
A
554-2008a, Specification for Welded Stainless Steel Mechanical Tubing (Item 45) (Sub .10)
A
588/A 588M-2005, Specification for High-strength Low-alloy Structural Steel, Up
to 50 Ksi 345 Mpa Minimum
Yield Point, with Atmospheric Corrosion Resistance (Item
2) (Sub .02)
A
638/A 638M-2000(2004), Specification for Precipitation Hardening Iron Base Superalloy Bars, Forgings, and Forging Stock for
High-temperature Service
(Item 57) (Sub .17)
A
649/A 649M-2009, Specification for Forged Steel Rolls Used for Corrugating
Paper Machinery (Item 18) (Sub .06)
A
659/A 659M-2008, Specification for Commercial Steel (cs),
Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-rolled (Item
78) (Sub .19) (CC)
A
671-2009, Specification for Electric-fusion-welded Steel Pipe for Atmospheric
and Lower Temperatures
(Item 26) (Sub .09)
A
709/A 709M-2009a, Specification for Structural Steel for Bridges (Item
3) (Sub .02)
A
757/A 757M-2000(2004), Specification for Steel Castings, Ferritic
and Martensitic, for Pressure-containing and Other
Applications, for Low-temperature Service (Item
66) (Sub .18) (CC)
A
779/A 779M-2005, Specification for Steel Strand, Seven-wire, Uncoated,
Compacted, Stress-relieved for Prestressed Concrete (Item 8) (Sub .05)
A
799/A 799M-2004(2009), Practice for Steel Castings, Stainless, Instrument Calibration,
for Estimating Ferrite Content (Item
67) (Sub .18)
A
886/A 886M-2005, Specification for Steel Strand, Indented, Seven-wire
Stress-relieved for Prestressed Concrete (Item
9) (Sub .05)
A
890/A 890M-1999(2007), Specification for Castings,
Iron-chromium-nickel-molybdenum Corrosion-resistant, Duplex (austenitic/ferritic) for General Application (Item
69) (Sub .18)
A
910/A 910M-2005, Specification for Uncoated, Weldless,
2- and 3-wire Steel Strand for Prestressed Concrete (Item 10) (Sub .05)
A
941-2009a, Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys (Items
92,93,94) (Sub .92)
A
958-2009E01, Specification for Steel Castings, Carbon and Alloy, with Tensile
Requirements, Chemical Requirements Similar to Standard Wrought Grades (Item 71) (Sub .18) (CC)
A
962/A 962M-2009, (Includes Change to Title) Specification for Common
Requirements for Steel Fasteners or Fastener Materials, or Both, Intended for
Use at Any Temperature from Cryogenic to the Creep Range (Item
88) (Sub .22) (CC)
A
990-2008, Specification for Castings, Iron-nickel-chromium and Nickel Alloys,
Specially Controlled for Pressure Retaining Parts for Corrosive Service (Item
72) (Sub .18)
A
991/A 991M-2008, Test Method for Conducting Temperature Uniformity Surveys of
Furnaces Used to Heat Treat Steel Products (Item
47) (Sub .13)
A
1002-1999(2009), Specification for Castings, Nickel-aluminum Ordered Alloy (Item 73) (Sub .18)
A
1008/A 1008M-2009a, Specification for Steel, Sheet, Cold-rolled, Carbon,
Structural, High-strength Low-alloy, High-strength Low-alloy with Improved
Formability, Solution Hardened, and Bake Hardenable (Item
79) (Sub .19)
A
1011/A 1011M-2009b, Specification for Steel, Sheet and Strip, Hot-rolled,
Carbon, Structural, High-strength Low-alloy, High-strength Low-alloy with
Improved Formability, and Ultra-high Strength
(Item 80) (Sub .19)
A
1014/A 1014M-2009, (Includes Change to Title) Specification for
Precipitation-hardening Fasteners and Fastener Material (uns
N07718) for High Temperature Service
(Item 89) (Sub .22) (CC)
A
1033-2004, Practice for Quantitative Measurement and Reporting of Hypoeutectoid Carbon and Low-alloy Steel Phase Transformations (Item 48) (Sub .13)
A
1040-2009, Guide for Specifying Harmonized Standard Grade Compositions for
Wrought Carbon, Low-alloy, and Alloy Steels (Items 95,96) (Sub .97)
REAPPROVAL
OF STANDARD
A
139/A 139M-2004, Specification for Electric-fusion Arc -welded Steel Pipe Nps 4 and Over (Item
22) (Sub .09)
A
290/A 290M-2005, Specification for Carbon and Alloy Steel Forgings for Rings
for Reduction Gears (Item 12) (Sub .06)
A
291/A 291M-2005, Specification for Steel Forgings, Carbon and Alloy, for
Pinions, Gears and Shafts for Reduction Gears (Item
13) (Sub .06)
A
311/A 311M-2004, Specification for Cold-drawn, Stress-relieved Carbon Steel
Bars Subject to Mechanical Property Requirements (Item
50) (Sub .15)
A
323-2005, Specification for Ferroboron (Item 58) (Sub .18)
A
334/A 334M-2004a, Specification for Seamless and Welded Carbon and Alloy-steel
Tubes for Low-temperature Service (Item
42) (Sub .10)
A
470/A 470M-2005E01, Specification for Vacuum-treated Carbon and Alloy Steel
Forgings for Turbine Rotors and Shafts (Item
16) (Sub .06)
A
481-2005, Specification for Chromium Metal (Item
60) (Sub .18)
A
482-2005, Specification for Ferrochrome-silicon (Item
61) (Sub .18)
A
508/A 508M-2005b, Specification for Quenched and Tempered Vacuum-treated Carbon
and Alloy Steel Forgings for Pressure Vessels (Item
17) (Sub .06)
A
530/A 530M-2004a, Specification for General Requirements for Specialized Carbon
and Alloy Steel Pipe (Item 24) (Sub .09)
A
601-2005, Specification for Electrolytic Manganese Metal (Item
63) (Sub .18)
A
618/A 618M-2004, Specification for Hot-formed Welded and Seamless High-strength
Low-alloy Structural Tubing
(Item 25) (Sub .09)
A
660-1996(2005), Specification for Centrifugally Cast Carbon Steel Pipe for
High-temperature Service
(Item 64) (Sub .18)
A
701-2005, Specification for Ferromanganese-silicon (Item
65) (Sub .18)
A
713-2004, Specification for Steel Wire, High-carbon Spring, for Heat-treated Components (Item 97) (Sub .03)
A
752-2004, Specification for General Requirements for Wire Rods and Coarse Round
Wire, Alloy Steel (Item 98) (Sub .03)
A
752M-2004, Specification for General Requirements for Wire Rods and Coarse
Round Wire, Alloy Steel Metric (Item
99) (Sub .03)
A
768/A 768M-2005, Specification for Vacuum-treated 12 Chromium Alloy Steel
Forgings for Turbine Rotors and Shafts (Item
19) (Sub .06)
A
769/A 769M-2005, Specification for Carbon and High-strength Electric Resistance
Forge-welded Steel Structural Shapes (Item
4) (Sub .02)
A
822/A 822M-2004, Specification for Seamless, Cold-drawn Carbon Steel Tubing for
Hydraulic System Service
(Item 27) (Sub .09)
A
835/A 835M-1984(2005), Specification for Sizes of Ferroalloys and Alloy Additives (Item 68) (Sub .18)
A
853-2004, Specification for Steel Wire, Carbon, for General Use (Item
100) (Sub .03)
A
905-2004, Specification for Steel Wire, Pressure Vessel Winding (Item
101) (Sub .03)
A
906/A 906M-2002, Specification for Grade 80 and Grade 100 Alloy Steel Chain
Slings for Overhead Lifting
(Item 90) (Sub .27)
A
922-2005, Specification for Silicon Metal (Item
70) (Sub .18)
A
952/A 952M-2002, Specification for Forged Grade 80 and Grade 100 Steel Lifting
Components and Welded Attachment Links
(Item 91) (Sub .27)
A
972/A 972M-2000(2004), Specification for Fusion Bonded Epoxy-coated Pipe Piles (Item 28) (Sub .09)
A
982/A 982M-2005, Specification for Steel Forgings, Stainless, for Compressor
and Turbine Airfoils (Item 20) (Sub .06)
A
1005/A 1005M-2000(2004), Specification for Steel Line Pipe, Black, Plain End,
Longitudinal and Helical Seam, Double Submerged-arc Welded (Item
29) (Sub .09)
A
1006/A 1006M-2000(2004), Specification for Steel Line Pipe, Black, Plain End,
Laser Beam Welded (Item 30) (Sub .09)
A
1021/A 1021M-2005, Specification for Martensitic
Stainless Steel Forgings and Forging Stock for High-temperature Service (Item
21) (Sub .06)
A
1025-2005, Specification for Ferroalloys and Other Alloying Materials, General Requirements (Item 74) (Sub .18)
A04 on Iron Castings
(#10-01)
REVISION
OF STANDARD
A
532/A 532M-1993A(2008), Specification for
Abrasion-resistant Cast Irons (Item 1) (Sub .01) (CC)
B01 on Electrical Conductors
(#10-01)
NEW
STANDARD
New
Standard, Specification for Silver-coated Braid and Ribbon Flat Copper Wire
Intended for Use in Electronic Application (Item
6) (Sub .04) (Ref. WK25222 )
New
Standard, Specification for Nickel-coated Braid and Ribbon Flat Copper Wire
Intended for Use in Electronic Application (Item
5) (Sub .04) (Ref. WK25223 )
New
Standard, Specification for Tin-coated Braid and Ribbon Flat Copper Wire
Intended for Use in Electronic Application (Item
7) (Sub .04) (Ref. WK25601 )
REVISION
OF STANDARD
B
33-2004, (Includes Change to Title) Specification for Tinned Soft or Annealed
Copper Wire for Electrical Purposes (Item
1) (Sub .04) (CC)
B
172-2001A(2007)E01, Specification for
Rope-lay-stranded Copper Conductors Having Bunch-stranded Members, for
Electrical Conductors (Item 2) (Sub .04)
B
173-2001A(2007)E01, Specification for Rope-lay-stranded
Copper Conductors Having Concentric-stranded Members, for Electrical
Conductors (Item 3) (Sub .04)
B
174-2002(2007)E01, Specification for Bunch-stranded
Copper Conductors for Electrical Conductors
(Item 4) (Sub .04)
B
501-2004, Specification for Silver-coated, Copper-clad Steel Wire for
Electronic Application
(Item 9) (Sub .06) (CC)
B
502-2002(2007), (Includes Change to Title) Specification for Aluminum-clad
Steel Core Wire for Aluminum Conductors, Aluminum-clad Steel Reinforced (Item 10) (Sub .06) (CC)
B
549-2004, (Includes Change to Title) Specification for Concentric-lay-stranded
Aluminum Conductors, Aluminum-clad Steel Reinforced Acsr/aw (Item 11) (Sub .07) (CC)
B02 on Nonferrous Metals and
Alloys (#10-01)
REVISION
OF STANDARD
B
86-2009b, Specification for Zinc and Zinc-aluminum (za)
Alloy Foundry and Die Castings (Item
8) (Sub .04)
B
240-2009, Specification for Zinc and Zinc-aluminum (za)
Alloys in Ingot Form for Foundry and Die Castings (Items 9,10) (Sub .04) (CC)
B
366-2004BE01, Specification for Factory-made Wrought Nickel and Nickel Alloy Fittings (Item 6) (Sub .07) (CC)
B
463-2004(2009), Specification for UNS N08020, UNS N08026, and UNS N08024 Alloy
Plate, Sheet, and Strip
(Item 14) (Sub .07)
B
464-2005(2009), Specification for Welded UNS N08020, N08024, and N08026 Alloy Pipe (Item 15) (Sub .07)
B
468-2004(2009), Specification for Welded UNS N08020, N08024, and N08026 Alloy Tubes (Item 16) (Sub .07)
B
892-2009, Specification for Acuzinc5 (zinc-copper-aluminum) Alloy in Ingot Form
for Die Castings (Item 11) (Sub .04) (CC)
B
894-2009, Specification for Acuzinc5 (zinc-copper-aluminum) Alloy Die Castings (Item 12) (Sub .04) (CC)
B
897-2009, Specification for Configuration of Zinc and Zinc Alloy Jumbo Block
and Half Block Ingot (Item 13) (Sub .04)
REAPPROVAL
OF STANDARD
B
23-2000(2005), Specification for White Metal Bearing Alloys (Item
1) (Sub .02)
B
237-2001(2006), Specification for Refined Antimony (Item
2) (Sub .02)
B
339-2000(2005), Specification for Pig Tin (Item
3) (Sub .02)
B
560-2000(2005), Specification for Modern Pewter Alloys (Item
4) (Sub .02)
B
774-2000(2005)E01, Specification for Low Melting Point
Alloys (Item 5) (Sub .02)
WITHDRAWAL
OF STANDARD
B
932-2004, Specification for Low-carbon Nickel-chromium-molybdenum-gadolinium
Alloy Plate, Sheet, and Strip
(Item 17) (Sub .07) (CC)
B05 on Copper and Copper
Alloys (#10-01)
REVISION
OF STANDARD
B
30-2009b, Specification for Copper Alloys in Ingot Form (Item
19) (Sub .05) (CC)
B
75-2002, Specification for Seamless Copper Tube (Item
15) (Sub .04)
B
103/B 103M-2009, Specification for Phosphor Bronze Plate, Sheet, Strip, and
Rolled Bar (Item 1) (Sub .01)
B
115-2000(2004), Specification for Electrolytic Copper Cathode (Item
23) (Sub .07)
B
124/B 124M-2009, Specification for Copper and Copper Alloy Forging Rod, Bar,
and Shapes (metric) (Items
5,6) (Sub .02) (CC)
B
249/B 249M-2009, Specification for General Requirements for Wrought Copper and
Copper-alloy Rod, Bar, Shapes and Forgings (metric) (Items 7,8) (Sub .02)
B
283-2009a, Specification for Copper and Copper-alloy Die Forgings (hot-pressed) (Item 9) (Sub .02) (CC)
B
422-2008a, Specification for Copper-aluminum-silicon-cobalt Alloy,
Copper-nickel-silicon-magnesium Alloy, Copper-nickel-silicon Alloy,
Copper-nickel-aluminum-magnesium Alloy, and (Item
2) (Sub .01)
B
455-2005, Specification for Copper-zinc-lead Alloy Leaded-brass Extruded Shapes (Item 11) (Sub .02)
B
505/B 505M-2009, Specification for Copper Alloy Continuous Castings (Item
20) (Sub .05)
B
694-2003, Specification for Copper, Copper-alloy, Copper-clad Bronze Ccb , Copper-clad Stainless Steel Ccs
, and Copper-clad Alloy Steel Cas Sheet and Strip for
Electrical Cable Shielding (Item 3) (Sub .01)
B
770-2009, Specification for Copper-beryllium Alloy Sand Castings for General
Applications (Item 21) (Sub .05) (CC)
B
813-2000(2009), Specification for Liquid and Paste Fluxes for Soldering of
Copper and Copper Alloy Tube (Item 16) (Sub .04) (CC)
B
846-2009a, Terminology for Copper and Copper Alloys (Items 25,26) (Sub .93)
B
888-2009, Specification for Copper Alloy Strip for Use in Manufacture of
Electrical Connectors or Spring Contacts
(Item 4) (Sub .01)
B
903-2000(2005), Specification for Seamless Copper Heat Exchanger Tubes with
Internal Enhancement (Item 17) (Sub .04) (CC)
B
956-2007E02, Specification for Welded Copper and Copper-alloy Condenser and
Heat Exchanger Tubes with Integral Fins
(Item 18) (Sub .04)
B
967/B 967M-2009, Specification for Copper-zinc-tin-bismuth Alloy Rod, Bar and
Wire (Item 13) (Sub .02) (CC)
B
968/B 968M-2009, Test Method Foroflattening of Copper
and Copper-alloy Pipe and Tube
(Item 22) (Sub .06) (CC)
F
68-2005E01, Specification for Oxygen-free Copper in Wrought Forms for Electron
Devices (Item 14) (Sub .02)
REAPPROVAL
OF STANDARD
B
170-1999(2004), Specification for Oxygen-free Electrolytic Copper --refinery
Shapes (Item 24) (Sub .07)
B
441-2004, Specification for Copper-cobalt-beryllium, Copper-nickel-beryllium,
and Copper-nickel-lead-beryllium Rod and Bar UNS Nos. C17500, C17510, and
C17465 (Item 10) (Sub .02)
WITHDRAWAL
OF STANDARD
B
938-2004, Specification for Copper-beryllium Alloy Forgings and Extrusions UNS
Nos. C17500 and C17510 (Item 12) (Sub .02) (CC)
B08 on Metallic and
Inorganic Coatings (#10-01)
REVISION
OF STANDARD
C
282-1999(2005), Test Method for Acid Resistance of Porcelain Enamels (Item
5) (Sub .12) (CC)
C
285-1988(2005), Test Methods for Sieve Analysis of Wet-milled and Dry-milled
Porcelain Enamel (Item 6) (Sub .12) (CC)
C
614-1974(2005), Test Method for Alkali Resistance of Porcelain Enamels (Item
7) (Sub .12) (CC)
C
664-1987(2005), Test Methods for Thickness of Diffusion Coating (Item
9) (Sub .12) (CC)
C
872-1989(2005), Test Method for Lead and Cadmium Release from Porcelain
Enamel (Item 11) (Sub .12) (CC)
REAPPROVAL
OF STANDARD
B
449-1993(2004), Specification for Chromates on Aluminum (Item
12) (Sub .07)
B
602-1988(2005), Test Method for Attribute Sampling of Metallic and Inorganic
Coatings (Item 1) (Sub .10)
B
697-1988(2005), Guide for Selection of Sampling Plans for Inspection of
Electrodeposited Metallic and Inorganic Coatings (Item
2) (Sub .10)
B
762-1990(2005), Test Method of Variables Sampling of Metallic and Inorganic
Coatings (Item 3) (Sub .10)
B
905-2000(2005), Test Methods for Assessing the Adhesion of Metallic and
Inorganic Coatings by the Mechanized Tape Test
(Item 4) (Sub .10)
C
660-1981(2005), Practices for Production and Preparation of Gray Iron Castings
for Porcelain Enameling (Item 8) (Sub .12)
C
839-1982(2005), Test Method for Compressive Stress of Porcelain Enamels by
Loaded-beam Method (Item 10) (Sub .12)
C01 on Cement (#10-01)
NEW
STANDARD
New
Standard, Practice for High-shear Mixing of Hydraulic Cement Pastes (Item
10) (Sub .22) (Ref. WK17835 )
REVISION
OF STANDARD
C
10/C 10M-2009, Specification for Natural Cement
(Item 1) (Sub .10)
C
187-2004, Test Method for Normal Consistency of Hydraulic Cement (Items 7,8,9) (Sub .22) (CC)
C
204-2007, Test Methods for Fineness of Hydraulic Cement by Air-permeability
Apparatus (Item 11) (Sub .25) (CC)
C
595/C 595M-2009, Specification for Blended Hydraulic Cements (Items 2,3) (Sub .10)
C
1038-2004, Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in
Water (Item 12) (Sub .28) (CC)
C
1157/C 1157M-2009, Performance Specification for Hydraulic Cement (Item
4) (Sub .10)
REAPPROVAL
OF STANDARD
C
806-2004, Test Method for Restrained Expansion of Expansive Cement Mortar (Item
5) (Sub .13)
C
845-2004, Specification for Expansive Hydraulic Cement (Item
6) (Sub .13)
C08 on Refractories
(#10-01)
REVISION
OF STANDARD
C
583-2005(2009), Test Method for Modulus of Rupture of Refractory Materials at
Elevated Temperatures (Item 1) (Sub .01) (CC)
REAPPROVAL
OF STANDARD
C
20-2000(2005), Test Methods for Apparent Porosity, Water ABSorption,
Apparent Specific Gravity, and Bulk Density of Burned Refractory Brick and
Shapes by Boiling Water (Item 3) (Sub .03)
C
134-1995(2005), Test Methods for Size, Dimensional Measurements, and Bulk
Density of Refractory Brick and Insulating Firebrick (Item
4) (Sub .03)
C
417-2005, Test Method for Thermal Conductivity of Unfired Monolithic Refractories
(Item 2) (Sub .02)
C
607-1988(2005), Practice for Coking Large Shapes of Carbon-bearing
Materials (Item 5) (Sub .04)
C09 on Concrete and Concrete
Aggregates (#10-01)
NEW
STANDARD
New
Standard, Guide for Evaluation of Alternative Supplementary Cementitious
Materials (ascm) for Use in Concrete (Item
2) (Sub .24) (CC) (Ref. WK15262
)
REVISION
OF STANDARD
C
78-2009, Test Method for Flexural Strength of Concrete (using Simple Beam with
Third-point Loading) (Item 11) (Sub .61) (CC)
C
94/C 94M-2009a, Specification for Ready-mixed Concrete (Item
4) (Sub .40)
C
125-2009a, Terminology Relating to Concrete and Concrete Aggregates (Items 17,18) (Sub .91)
C
293-2008, Test Method for Flexural Strength of Concrete (using Simple Beam with
Center-point Loading) (Item 12) (Sub .61) (CC)
C
418-2005, (Includes Change to Title) Test Method for Abrasion Resistance of
Concrete by Sandblasting (Item 13) (Sub .62) (CC)
C
457-2009, Test Method for Microscopical Determination
of Parameters of the Air-void System in Hardened Concrete (Item
14) (Sub .65)
C
1077-2010, Practice for Laboratories Testing Concrete and Concrete Aggregates
for Use in Construction and Criteria for Laboratory Evaluation (Items 19,20,21) (Sub .98)
C
1084-2002, Test Method for Portland-cement Content of Hardened Hydraulic-cement
Concrete (Items 15,16) (Sub .69)
C
1140-2003a, Practice for Preparing and Testing Specimens from Shotcrete Test Panels
(Item 5) (Sub .46)
C
1240-2005, Specification for Silica Fume Used in Cementitious
Mixtures (Item 1) (Sub .24) (CC)
C
1550-2008, Test Method for Flexural Toughness of Fiber Reinforced Concrete
(using Centrally Loaded Round Panel)
(Items 6,7,8) (Sub .42)
C
1688/C 1688M-2008, Test Method for Density and Void Content of Freshly Mixed
Pervious Concrete (Item 10) (Sub .49) (CC)
WITHDRAWAL
OF STANDARD
C
1398-2007, Test Method for the Laboratory Determination of the Time of Setting
of Hydraulic-cement Mortars Containing Additives for Shotcrete
by the Use of Gillmore Needles (Item
9) (Sub .46) (CC)
C
1404/C 1404M-1998(2003), Test Method for Bond Strength of Adhesive Systems Used
with Concrete as Measured by Direct Tension
(Item 3) (Sub .25) (CC)
C14 on Glass and Glass
Products (#10-02)
REVISION
OF STANDARD
C
1651-2008, Test Method for Measurement of Roll Wave Optical Distortion in
Heat-treated Flat Glass (Item 1) (Sub .11) (CC)
REAPPROVAL
OF STANDARD
C
336-1971(2005), Test Method for Annealing Point and Strain Point of Glass by
Fiber Elongation (Item 2) (Sub .04)
C
623-1992(2005)E01, Test Method for Young S Modulus, Shear Modulus, and Poisson
S Ratio for Glass and Glass-ceramics by Resonance (Item
3) (Sub .04)
C
829-1981(2005), Practices for Measurement of Liquidus
Temperature of Glass by the Gradient Furnace Method (Item
4) (Sub .04)
F
14-1980(2005), Practice for Making and Testing Reference Glass-metal
Bead-seal (Item 6) (Sub .04)
F
105-1972(2005), Specification for Type 58 Borosilicate Sealing Glass (Item
5) (Sub .04)
F
144-1980(2005), Practice for Making Reference Glass-metal Sandwich Seal and
Testing for Expansion Characteristics by Polarimetric
Methods (Item 7) (Sub .04)
C18 on Dimension Stone
(#10-01)
REVISION
OF STANDARD
C
1242-2005, (Includes Change to Title) Guide for Selection, Design, and
Installation of Dimension Stone Anchoring Systems (Item
1) (Sub .06) (CC)
C21 on Ceramic Whitewares and Related Products (#10-01)
REVISION
OF STANDARD
C
627-1993(2007), Test Method for Evaluating Ceramic Floor Tile Installation
Systems Using the Robinson-type Floor Tester
(Item 6) (Sub .06) (CC)
C
1023-2009, Practice for Labeling Ceramic Art Materials for Chronic Adverse
Health Hazards (Items 1,2,3,4,5) (Sub
.03)
D10 on Packaging (#10-01)
REVISION
OF STANDARD
D
2063/D 2063M-2009, (Includes Change to Title) Test Methods for Measurement of
Torque Retention for Packages with Continuous Thread Closures (Item
6) (Sub .32) (CC)
D
5570-1994(2005), Test Method for Water Resistance of Tape and Adhesives Used as
Box Closure (Item 5) (Sub .27)
REAPPROVAL
OF STANDARD
D
951-1999(2004), Test Method for Water Resistance of Shipping Containers by
Spray Method (Item 3) (Sub .23)
D
2860/D 2860M-2004, Test Method for Adhesion of Pressure-sensitive Tape to
Fiberboard at 90 Deg; Angle and Constant Stress
(Item 1) (Sub .14)
D
3330/D 3330M-2004, Test Method for Peel Adhesion of Pressure-sensitive
Tape (Item 2) (Sub .14)
D
5571-1994(2005), Test Method for Environmental Stress Crack Resistance Escr of Plastic Tighthead Drums
Not Exceeding 60 Gal 227 L in Rated Capacity
(Item 4) (Sub .23)
WITHDRAWAL
OF STANDARD
D
7077-2004, Test Method for Evaluation of Drop Size by Weight of Solutions and
Suspensions (Item 7) (Sub .32) (CC)
D14 on Adhesives (#10-01)
REVISION
OF STANDARD
D
2559-2009, Specification for Adhesives for Structural Laminated Wood Products
for Use Under Exterior Wet Use Exposure Conditions (Item
1) (Sub .30) (CC)
REAPPROVAL
OF STANDARD
D
3929-2003, Test Method for Evaluating Stress Cracking of Plastics by Adhesives
Using the Bent-beam Method (Item 2) (Sub .40)
D15 on Engine Coolants
(#10-01)
REVISION
OF STANDARD
D
3306-2009, Specification for Glycol Base Engine Coolant for Automobile and
Light-duty Service (Item 1) (Sub .07) (CC)
D
4985-2009, Specification for Low Silicate Ethylene Glycol Base Engine Coolant
for Heavy Duty Engines Requiring a Pre-charge of Supplemental Coolant Additive
(sca)
(Item 2) (Sub .07) (CC)
D
5752-2005, Specification for Supplemental Coolant Additives Scas
for Use in Precharging Coolants for Heavy-duty
Engines (Item 3) (Sub .07) (CC)
D
6471-2006, Specification for Recycled Prediluted
Aqueous Glycol Base Engine Coolant 50 Volume Minimum for Automobile and
Light-duty Service (Item 5) (Sub .15) (CC)
D
6472-2006, Specification for Recycled Glycol Base Engine Coolant Concentrate
for Automobile and Light-duty Service
(Item 6) (Sub .15) (CC)
D
7518-2009, Specification for 1,3 Propanediol (pdo) Base Engine Coolant for Automobile and Light-duty
Service (Item 4) (Sub .07) (CC)
D20 on Plastics (#10-01)
NEW
STANDARD
New
Standard, Practice for Heat and Humidity Aging of Oxidatively
Degradable Plastics (Item 32) (Sub .96) (CC) (Ref. WK16000 )
New
Standard, Test Method for Weight Attrition of Plastic Materials in the Marine
Environment by Open System Aquarium Incubations
(Item 33) (Sub .96) (CC) (Ref.
WK17751 )
New
Standard, Test Method for Determining the Aerobic Degradation and Anaerobic
Biodegradation of Plastic Materials Under Accelerated Bioreactor Landfill
Conditions (Item 34) (Sub .96) (CC) (Ref. WK19580 )
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
256-2006AE01, Test Methods for Determining the Izod
Pendulum Impact Resistance of Plastics
(Item 1) (Sub .10) (CC)
D20 on Plastics (#10-01)
REVISION
OF STANDARD
D
638-2008, Test Method for Tensile Properties of Plastics (Item
2) (Sub .10) (CC)
D
695-2008, Test Method for Compressive Properties of Rigid Plastics (Item
3) (Sub .10) (CC)
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
731-2008, Test Method for Molding Index of Thermosetting Molding Powder (Item
9) (Sub .30) (CC)
D20 on Plastics (#10-01)
REVISION
OF STANDARD
D
732-2009, Test Method for Shear Strength of Plastics by Punch Tool (Item
4) (Sub .10) (CC)
D
747-2008, Test Method for Apparent Bending Modulus of Plastics by Means of a
Cantilever Beam (Item 5) (Sub .10) (CC)
D
790-2007E01, Test Methods for Flexural Properties of Unreinforced and
Reinforced Plastics and Electrical Insulating Materials (Item
6) (Sub .10) (CC)
D
882-2009, Test Method for Tensile Properties of Thin Plastic Sheeting (Item
17) (Sub .19) (CC)
D
883-2008, Terminology Relating to Plastics
(Item 27) (Sub .92) (CC)
D
952-2002, Test Method for Bond or Cohesive Strength of Sheet Plastics and
Electrical Insulating Materials
(Item 7) (Sub .10) (CC)
D
953M-2009, Test Method for Bearing Strength of Plastics (Item
8) (Sub .10) (CC)
D
1043-2009, Test Method for Stiffness Properties of Plastics as a Function of
Temperature by Means of a Torsion Test
(Item 9) (Sub .10) (CC)
D
1505-2003, Test Method for Density of Plastics by the Density-gradient
Technique (Item 26) (Sub .70) (CC)
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
1621-2004a, Test Method for Compressive Properties of Rigid Cellular Plastics (Item
7) (Sub .22) (CC)
D20 on Plastics (#10-01)
REVISION
OF STANDARD
D
1708-2006a, Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
(Item 10) (Sub .10) (CC)
D
2103-2008, Specification for Polyethylene Film and Sheeting (Item
18) (Sub .19)
D
2647-2005a, Specification for Crosslinkable Ethylene
Plastics (Item 14) (Sub .15) (CC)
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
2839-2005, Practice for Use of a Melt Index Strand for Determining Density of
Polyethylene (Item 6) (Sub .15) (CC)
D20 on Plastics (#10-01)
REVISION
OF STANDARD
D
3840-2001(2005), Specification for "fiberglass "
Glass-fiber-reinforced Thermosetting-resin Pipe Fittings for Nonpressure Applications
(Item 22) (Sub .23) (CC)
D
4000-2009b, Classification System for Specifying Plastic Materials (Item
28) (Sub .94) (CC)
D
4101-2009, Specification for Polypropylene Injection and Extrusion
Materials (Item 15) (Sub .15) (CC)
D
4385-2008, Practice for Classifying Visual Defects in Thermosetting Reinforced
Plastic Pultruded Products (Item
16) (Sub .18) (CC)
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
4508-2006, Test Method for Chip Impact Strength of Plastics (Item
2) (Sub .10) (CC)
D20 on Plastics (#10-01)
REVISION
OF STANDARD
D
4703-2007, Practice for Compression Molding Thermoplastic Materials Into Test
Specimens, Plaques, or Sheets (Item 1) (Sub .09) (CC)
D
5083-2008, Test Method for Tensile Properties of Reinforced Thermosetting
Plastics Using Straight-sided Specimens
(Item 11) (Sub .10) (CC)
D
5155-2007, Test Methods for Polyurethane Raw Materials Determination of the Isocyanate Content of Aromatic Isocyanates (Item
21) (Sub .22) (CC)
D
5511-2002, Test Method for Determining Anaerobic Biodegradation of Plastic Materials
Under High-solids Anaerobic-digestion Conditions (Item
29) (Sub .96) (CC)
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
5523-2004, Test Method for Polyurethane Raw Materials: Acidity by Argentometric Determination of Hydrolyzable
Chlorine in Monomeric, Aromatic Isocyanates (Item
8) (Sub .22) (CC)
D20 on Plastics (#10-01)
REVISION
OF STANDARD
D
5926-2009, Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain,
Waste, and Vent (dwv), Sewer, Sanitary, and Storm
Plumbing Systems (Item 24) (Sub .24) (CC)
D
5998-2003, Specification for Molded Polyethylene Shipping and Storage
Drums (Item 19) (Sub .15) (CC)
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
6110-2008, Test Method for Determining the Charpy
Impact Resistance of Notched Specimens of Plastics (Item
3) (Sub .10) (CC)
D20 on Plastics (#10-01)
REVISION
OF STANDARD
D
6272-2002(2008)E01, Test Method for Flexural Properties of Unreinforced and
Reinforced Plastics and Electrical Insulating Materials by Four-point Bending (Item
13) (Sub .10) (CC)
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
6395-2005, Test Method for Flatwise Flexural Impact
Resistance of Rigid Plastics (Item 4) (Sub .10) (CC)
D20 on Plastics (#10-01)
REVISION
OF STANDARD
D
6868-2003, (Includes Change to Title) Specification for Biodegradable Plastics
Used as Coatings on Paper and Other Compostable Substrates (Item
31) (Sub .96) (CC)
D20 on Plastics (#10-02)
REVISION
OF STANDARD
D
7191-2005, Test Method for Determination of Moisture in Plastics by Relative
Humidity Sensor (Item 10) (Sub .70) (CC)
D
7192-2008a, Test Method for High Speed Puncture Properties of Plastic Films
Using Load and Displacement Sensors
(Item 5) (Sub .10) (CC)
D20 on Plastics (#10-01)
REAPPROVAL
OF STANDARD
D
570-1998(2005), Test Method for Water ABSorption of
Plastics (Item 25) (Sub .50)
D
4161-2001(2005), Specification for "fiberglass "
Glass-fiber-reinforced Thermosetting-resin Pipe Joints Using Flexible
Elastomeric Seals (Item 23) (Sub .23)
D
5526-1994(2002), Test Method for Determining Anaerobic Biodegradation of
Plastic Materials Under Accelerated Landfill Conditions (Item
30) (Sub .96)
D
5592-1994(2002)E01, Guide for Material Properties Needed in Engineering Design
Using Plastics (Item 12) (Sub .10)
D
7082-2004, Specification for Polyethylene Stay in Place Form System for End
Walls for Drainage Pipe (Item 20) (Sub .24)
D22 on Air Quality (#10-01)
NEW
STANDARD
New
Standard, Test Method for Determination of Total Suspended Particulate (tsp) Hexavalent Chromium in Ambient Air Analyzed by Ion
Chromatography (ic) and Spectrophotometirc
Measurments
(Item 6) (Sub .03) (CC) (Ref.
WK21495 )
REVISION
OF STANDARD
D
3195-1990(2004), Practice for Rotameter
Calibration (Item 3) (Sub .01) (CC)
D
4532-1997(2003), Test Method for Respirable Dust in
Workplace Atmospheres (Item 7) (Sub .04) (CC)
D
5116-2006, Guide for Small-scale Environmental Chamber Determinations of
Organic Emissions from Indoor Materials/products (Item
13) (Sub .05)
D
6271-2004, Test Method for Estimating Contribution of Environmental Tobacco
Smoke to Respirable Suspended Particles Based on Solanesol (Item 14) (Sub .05) (CC)
D
6306-1998(2003), Guide for Placement and Use of Diffusion Controlled Passive
Monitors for Gaseous Pollutants in Indoor Air
(Item 15) (Sub .05) (CC)
D
6327-1998(2004), Test Method for Determination of Radon Decay Product
Concentration and Working (Item 16) (Sub .05) (CC)
D
6333-1998(2004)E01, Practice for Collection of Dislodgeable
Pesticide Residues from Floors
(Item 17) (Sub .05) (CC)
D
6345-1998(2004)E01, Guide for Selection of Methods for Active, Integrative
Sampling of Volatile Organic Compounds in Air
(Item 18) (Sub .05) (CC)
D
6399-2004, Guide for Selecting Instruments and Methods for Measuring Air
Quality in Aircraft Cabins (Item 19) (Sub .05) (CC)
D
7035-2004, Test Method for Determination of Metals and Metalloids in Airborne
Particulate Matter by Inductively Coupled Plasma Atomic Emission Spectrometry Icp-aes (Item 8) (Sub .04) (CC)
REAPPROVAL
OF STANDARD
D
1356-2005, Terminology Relating to Sampling and Analysis of Atmospheres (Item
1) (Sub .01)
D
1914-1995(2004)E01, Practice for Conversion Units and Factors Relating to
Sampling and Analysis of Atmospheres
(Item 2) (Sub .01)
D
3609-2000(2005), Practice for Calibration Techniques Using Permeation
Tubes (Item 4) (Sub .01)
D
4298-2004, Guide for Intercomparing Permeation Tubes
to Establish Traceability (Item 5) (Sub .01)
D
4856-1999(2004), Test Method for Determination of Sulfuric Acid Mist in the
Workplace Atmosphere Ion Chromatographic
(Item 9) (Sub .04)
D
5578-2004, Test Method for Determination of Ethylene Oxide in Workplace
Atmospheres Hbr Derivatization
Method (Item 10) (Sub .04)
D
6494-1999(2004)E01, Test Method for Determination of Asphalt Fume Particulate
Matter in Workplace Atmospheres as Benzene Soluble Fraction (Item
11) (Sub .04)
D
6589-2005, Guide for Statistical Evaluation of Atmospheric Dispersion Model
Performance (Item 20) (Sub .11)
D
7049-2004, Test Method for Metal Removal Fluid Aerosol in Workplace
Atmospheres (Item 12) (Sub .04)
D
7145-2005, Guide for Measurement of Atmospheric Wind and Turbulence Profiles by
Acoustic Means (Item 21) (Sub .11)
D28 on Activated Carbon
(#10-01)
REVISION
OF STANDARD
D
2862-1997(2009)E01, Test Method for Particle Size Distribution of Granular
Activated Carbon (Item 3) (Sub .04) (CC)
D
3802-1979(2005), Test Method for Ball-pan Hardness of Activated Carbon (Item
4) (Sub .04) (CC)
REAPPROVAL
OF STANDARD
D
5228-1992(2005), Test Method for Determination of Butane Working Capacity of
Activated Carbon (Item 1) (Sub .04)
D
5742-1995(2005), Test Method for Determination of Butane Activity of Activated
Carbon (Item 2) (Sub .04)
D30 on Composite Materials
(#10-01)
NEW
STANDARD
New
Standard, Practice for Open- Hole Fatigue Response of Polymer Matrix Composite
Laminates (Item 7) (Sub .05) (CC) (Ref. WK14526 )
New
Standard, Method for Determining Overlap Splice Shear Strength Properties of
Wet Lay-up Fiber-reinforced Polymer Matrix Composites Used for Strengthening
Civil Structures (Item 8) (Sub .05) (CC) (Ref. WK22346 )
New
Standard, Test Method for Transverse Shear Strength of Fiber Reinforced Polymer
Matrix Composite Bars (Item 9) (Sub .05) (CC) (Ref. WK22348 )
REVISION
OF STANDARD
D
5961/D 5961M-2008, Test Method for Bearing Response of Polymer Matrix Composite
Laminates (Item 5) (Sub .05)
D
7565/D 7565M-2009, Test Method for Determining Tensile Properties of Fiber
Reinforced Polymer Matrix Composites Used for Strengthening of Civil
Structures (Item 6) (Sub .05) (CC)
REAPPROVAL
OF STANDARD
D
3800-1999(2004), Test Method for Density of High-modulus Fibers (Item
1) (Sub .03)
D
5229/D 5229M-1992(2004), Test Method for Moisture ABSorption
Properties and Equilibrium Conditioning of Polymer Matrix Composite
Materials (Item 2) (Sub .04)
D
5379/D 5379M-2005, Test Method for Shear Properties of Composite Materials by
the V-notched Beam Method (Item 3) (Sub .04)
D
7078/D 7078M-2005, Test Method for Shear Properties of Composite Materials by
the V-notched Rail Shear Method
(Item 4) (Sub .04)
D31 on Leather (#10-01)
REVISION
OF STANDARD
D
2322-2000(2005), Test Method for Resistance of Shoe Upper Leather to Artificial
Perspiration (Item 9) (Sub .03) (CC)
D
6077-2000(2005), Test Method for Trapezoid Tearing Strength of Leather (Item
21) (Sub .05) (CC)
REAPPROVAL
OF STANDARD
D
1611-2000(2005), Test Method for Corrosion Produced by Leather in Contact with
Metal (Item 1) (Sub .01)
D
1912-2000(2005)E01, Test Method for Cold-crack Resistance of Upholstery
Leather (Item 16) (Sub .05)
D
1913-2000(2005), Test Method for Resistance to Wetting of Garment-type
Leathers (Item 11) (Sub .04)
D
2096-2000(2005)E01, Test Method for Colorfastness and Transfer of Color in the
Washing of Leather (Item 12) (Sub .04)
D
2097-2003(2005), Test Method for Flex Testing of Finish on Upholstery
Leather (Item 17) (Sub .05)
D
2099-2005, Test Method for Dynamic Water Resistance of Shoe Upper Leather by
the Maeser Water Penetration Tester (Item
10) (Sub .03)
D
2208-2000(2005), Test Method for Breaking Strength of Leather by the Grab
Method (Item 18) (Sub .05)
D
2209-2000(2004), Test Method for Tensile Strength of Leather (Item
20) (Sub .07)
D
2213-2000(2005), Test Method for Compressibility of Leather (Item
2) (Sub .01)
D
2875-2000(2005), Test Method for Insoluble Ash of Vegetable-tanned Leather (Item
3) (Sub .01)
D
2876-2000(2005), Test Method for Water-soluble Matter of Vegetable-tanned
Leather (Item 4) (Sub .01)
D
4786-2000(2005), Test Method for Stitch Tear Strength, Single Hole (Item
5) (Sub .01)
D
4831-2000(2005), Test Method for Buckle Tear Strength of Leather (Item
6) (Sub .01)
D
5552-2000(2005), Test Method for Resistance of Colored Leather to Bleeding (Item
13) (Sub .04)
D
6013-2000(2005), Test Method for Determination of Area Stability of Leather to
Laundering (Item 14) (Sub .04)
D
6014-2000(2005), Test Method for Determination of Dynamic Water ABSorption of Leather Surfaces (Item
15) (Sub .04)
D
6020-2000(2005), Practice for Calculation of Non-mineral Combined Tanning
Agents and Degree of Tannage (Item
7) (Sub .01)
D
6075-2000(2005), Test Method for Cracking Resistance of Leather (Item
8) (Sub .01)
D
6116-2000(2005), Test Method for Blocking
(Item 19) (Sub .05)
D32 on Catalysts (#10-01)
REVISION
OF STANDARD
D
3943-2004, Test Method for Total Molybdenum in Fresh Alumina-base
Catalysts (Item 1) (Sub .03) (CC)
D
4481-2004, Test Method for Total Nickel in Fresh Alumina-base Catalysts (Item
2) (Sub .03) (CC)
D
4782-2004, Test Method for Palladium in Molecular Sieve Catalyst by Wet
Chemistry (Item 3) (Sub .03) (CC)
D
5154-2005, Test Method for Determining Activity and Selectivity of Fluid
Catalytic Cracking Fcc Catalysts by Microactivity Test
(Item 5) (Sub .04) (CC)
REAPPROVAL
OF STANDARD
D
7085-2004E01, Guide for Determination of Chemical Elements in Fluid Catalytic
Cracking Catalysts by X-ray Fluorescence Spectrometry Xrf (Item
4) (Sub .03)
D33 on Protective Coating
and Lining Work for Power Generation Facilities (#10-01)
NEW
STANDARD
New
Standard, Test Method for Chemical Resistance of Coatings Used in Light-water
Nuclear Power Plants (Item 1) (Sub .02) (CC) (FORMERLY
D3912-1995(2001) )
New
Standard, Specification for Sample Preparation for Qualification Testing of
Coatings to Be Used in Nuclear Power Plants
(Item 3) (Sub .02) (CC) (FORMERLY
D5139-1990(2001) )
REVISION
OF STANDARD
D
4082-2002, Test Method for Effects of Gamma Radiation on Coatings for Use in
Light-water Nuclear Power Plants
(Item 2) (Sub .02) (CC)
E04 on Metallography
(#10-01)
NEW
STANDARD
New
Standard, Test Methods for Measuring Layered Materials Using Optical Microscopy
of Cross-sectional Samples (Item 5) (Sub .14)
(Ref. WK25749 )
New
Standard, Practice for Determining Average Grain Size Using Electron
Backscatter Diffraction (ebsd) in Fully Recrystallized Polycrystalline Materials (Item
4) (Sub .11) (CC) (Ref. WK3577
)
REVISION
OF STANDARD
E
45-2005E03, Test Methods for Determining the Inclusion Content of Steel (Items 1,2,3) (Sub .09) (CC)
REAPPROVAL
OF STANDARD
E
963-1995(2004), Practice for Electrolytic Extraction of Phases from Ni and Ni-fe Base Superalloys Using a
Hydrochloric-methanol Electrolyte
(Item 6) (Sub .11)
E
986-2004, Practice for Scanning Electron Microscope Beam Size
Characterization (Item 7) (Sub .11)
E05 on Fire Standards
(#10-01)
NEW
STANDARD
New
Standard, Guide for Fire-resistance Experiments
(Item 1) (Sub .11) (Ref. WK13922 )
New
Standard, Practice for Measuring the Uniformity of Furnace Exposure on Test
Specimens (Item 2) (Sub .11) (CC) (Ref. WK23795 )
New
Standard, Guide for Extension of Data for Penetrations Seals (Item
3) (Sub .11) (CC) (Ref. WK26086
)
REVISION
OF STANDARD
E
119-2009c, Test Methods for Fire Tests of Building Construction and
Materials (Items 4,5) (Sub .11) (CC)
E
648-2009a, Test Method for Critical Radiant Flux of Floor-covering Systems
Using a Radiant Heat Energy Source
(Items 20,21) (Sub .22) (CC)
E
814-2009, Test Method for Fire Tests of Penetration Firestop
Systems (Items 6,7,8,9,10) (Sub .11)
(CC)
E
906-2009, Test Method for Heat and Visible Smoke Release Rates for Materials
and Products Using a Thermopile Method
(Item 17) (Sub .21)
E
970-2008a, Test Method for Critical Radiant Flux of Exposed Attic Floor
Insulation Using a Radiant Heat Energy Source
(Item 19) (Sub .22)
E
1623-2009, Test Method for Determination of Fire and Thermal Parameters of
Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ical) (Item 18) (Sub .21)
E
2226-2008, Practice for Application of Hose Stream (Item
11) (Sub .11) (CC)
E
2307-2004E01, Test Method for Determining Fire Resistance of Perimeter Fire
Barriers Using Intermediate-scale, Multi-story Test Apparatus (Items 12,13,14,15,16) (Sub .11) (CC)
E06 on Performance of
Buildings (#10-01)
NEW
STANDARD
New
Standard, Practice for Design and Performance of Supported Glass Walkways (Item
18) (Sub .56) (CC) (Ref. WK9258
)
REVISION
OF STANDARD
E
72-2005, Test Methods of Conducting Strength Tests of Panels for Building
Construction (Item 8) (Sub .11) (CC)
E
241-2009, Guide for Limiting Water-induced Damage to Buildings (Items 13,14) (Sub .41) (CC)
E
455-2004, Test Method for Static Load Testing of Framed Floor or Roof Diaphragm
Constructions for Buildings (Items
1,2,3,4,5,6,7) (Sub .11) (CC)
E
779-2010, Test Method for Determining Air Leakage Rate by Fan
Pressurization (Item 15) (Sub .41) (CC)
E
1643-2009, Practice for Installation of Water Vapor Retarders Used in Contact
with Earth or Granular Fill Under Concrete Slabs (Item
10) (Sub .21) (CC)
E
1699-2000(2005), (Includes Change to Title) Practice for Performing Value
Analysis Va of Buildings and Building Systems (Item
23) (Sub .81) (CC)
E
2168-2006, Classification for Allowance, Contingency and Reserve Sums in
Building Construction Estimating (Items
26,27) (Sub .81) (CC)
REAPPROVAL
OF STANDARD
E
330-2002, Test Method for Structural Performance of Exterior Windows, Doors,
Skylights and Curtain Walls by Uniform Static Air Pressure Difference (Item
16) (Sub .51)
E
917-2005E01, Practice for Measuring Life-cycle Costs of Buildings and Building
Systems (Item 24) (Sub .81)
E
1602-2003, Guide for Construction of Solid Fuel Burning Masonry Heaters (Item
17) (Sub .54)
E
1663-2003, Classification for Serviceability of an Office Facility for Typical
Office Information Technology (Item 11) (Sub .25)
E
2083-2005, Classification for Building Construction Field Requirements, and
Office Overhead Amp; Profit (Item 25) (Sub .81)
E
2320-2004, Classification for Serviceability of an Office Facility for Thermal
Environment and Indoor Air Conditions
(Item 12) (Sub .25)
WITHDRAWAL
OF STANDARD
E
577-1985(2002), Guide for Dimensional Coordination of Rectilinear Building
Parts and Systems (Item 19) (Sub .21) (CC)
E
713-1988(2002), Guide for Selection of Scales for Metric Building Drawings (Item
20) (Sub .21) (CC)
E
835/E 835M-1993(2002), Guide for Modular Coordination of Clay and Concrete
Masonry Units (Item 21) (Sub .21) (CC)
E
1494-1992(2002), Practice for Encapsulants for Spray-
or Trowel-applied Friable Asbestos-containing Building Materials (Item
22) (Sub .21) (CC)
E17 on Vehicle - Pavement
Systems (#10-01)
REAPPROVAL
OF STANDARD
E
1957-2004, Practice for Installing Using Pneumatic Tubes with Roadway Traffic
Counters and Classifiers (Item 3) (Sub .52)
E
2213-2003, Specification for Telecommunications and Information Exchange
Between Roadside and Vehicle Systems -- 5 Ghz Band
Dedicated Short Range Communications Dsrc Medium
Access Control Mac and Physical Layer Phy
Specifications (Item 2) (Sub .51)
WITHDRAWAL
OF STANDARD
E
503/E 503M-1988(2004), Test Methods for Measurement of Skid Resistance on Paved
Surfaces Using a Passenger Vehicle Diagonal Braking Technique (Item
1) (Sub .21) (CC)
E21 on Space Simulation and
Applications of Space Technology (#10-01)
REAPPROVAL
OF STANDARD
E
296-1970(2004), Practice for Ionization Gage Application to Space
Simulators (Item 1) (Sub .04)
E
491-1973(2004)E01, Practice for Solar Simulation for Thermal Balance Testing of
Spacecraft (Item 2) (Sub .04)
E
512-1994(2004), Practice for Combined, Simulated Space Environment Testing of
Thermal Control Materials with Electromagnetic and Particulate Radiation (Item
3) (Sub .04)
E
2352-2004, Practice for Aerospace Cleanrooms and
Associated Controlled Environments --cleanroom
Operations (Item 4) (Sub .05)
F
309-2004, Practice for Liquid Sampling of Noncryogenic
Aerospace Propellants (Item 5) (Sub .05)
E34
on Occupational Health and Safety (#10-01)
WITHDRAWAL
OF STANDARD
E
1718-1995(2004), Guide for Administrative and Engineering Controls for Silicon
Carbide Whisker Work Areas (Item 2) (Sub .70) (CC)
E35 on Pesticides and
Alternative Control Agents (#10-01)
NEW
STANDARD
New
Standard, Test Method for Determining the Antimicrobial Activity of Immobilized
Antimicrobial Agents Under Dynamic Contact Conditions (Item
7) (Sub .15) (CC) (FORMERLY E2149-2001 )
New
Standard, Specification for Specification for Eretmocerus
Eremicus Rose and Zolnerowich (hymenoptera: Aphelinidae)) (Item
71) (Sub .30) (Ref. WK16168 )
New
Standard, Test Method for Evaluation of the Effectiveness of Decontamination
Procedures for Air-permeable Materials When Challenged with Biological Aerosols
Containing Human Pathogenic Viruses
(Item 11) (Sub .15) (CC) (Ref.
WK19887 )
New
Standard, Test Method for Evaluation of the Effectiveness of Decontamination
Procedures for Surfaces When Challenged with Droplets Containing Human
Pathogenic Viruses (Item 12) (Sub .15) (CC) (Ref. WK19888 )
New
Standard, Specification for Delphastus Catalinae (horn) (coleoptera:coccinellidae). (Item
72) (Sub .30) (Ref. WK21730 )
New
Standard, Test Method for Determining the Bacteria-eliminating Effectiveness of
Hand Sanitizer Formulations Using Hands of Adults (Item
13) (Sub .15) (CC) (Ref. WK23789
)
New
Standard, Terminology for Antimicrobial and Antiviral Agents (Items
14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70)
(Sub .15) (Ref. WK25957 )
New
Standard, Guidelines for Evaulation of Residual
Effectiveness of Antibacterial Personal Cleansing Products (Item
10) (Sub .15) (Ref. WK9062 )
REVISION
OF STANDARD
E
875-2000(2005), Test Method for Efficacy of Fungal Control Agents as
Preservatives for Aqueous-based Products Used in the Paper Industry (Item
1) (Sub .15) (CC)
E
1053-1997(2002), (Includes Change to Title) Test Method for Efficacy of Virucidal Agents Intended for Inanimate Environmental
Surfaces (Item 2) (Sub .15) (CC)
E
1115-2002, Test Method for Evaluation of Surgical Hand Scrub Formulation (Item
9) (Sub .15)
E
1838-2002, (Includes Change to Title) Test Method for Determining the
Virus-eliminating Effectiveness of Liquid Hygienic Handwash
and Handrub Agents Using the Fingerpads
of Adult Volunteers (Item 5) (Sub .15) (CC)
E
1882-2005, Test Method for Evaluation of Antimicrobial Formulations by the Agar
Patch Technique (Item 6) (Sub .15) (CC)
E
2276-2003E01, (Includes Change to Title) Test Method for Determining the
Bacteria-eliminating Effectiveness of Hygienic Handwash
and Handrub Agents Using the Fingerpads
of Adult Subjects (Item 8) (Sub .15) (CC)
REAPPROVAL
OF STANDARD
E
1153-2003, Test Method for Efficacy of Sanitizers Recommended for Inanimate
Non-food Contact Surfaces (Item 3) (Sub .15)
E
1589-2005, Test Method for Evaluation of First Aid Antiseptic Drug
Products (Item 4) (Sub .15)
E37 on Thermal Measurements
(#10-01)
REVISION
OF STANDARD
E
1142-2007, Terminology Relating to Thermophysical
Properties (Items 1,2,3,4,5,6,7) (Sub
.03)
E
1269-2005, Test Method for Determining Specific Heat Capacity by Differential
Scanning Calorimetry
(Item 8) (Sub .01) (CC)
E
1582-2004, Practice for Calibration of Temperature Scale for Thermogravimetry
(Item 9) (Sub .01) (CC)
E
1719-2005, Test Method for Vapor Pressure of Liquids by Ebulliometry (Item
10) (Sub .01) (CC)
E
2584-2007, Practice for Thermal Conductivity of Materials Using a Thermal
Capacitance (slug) Calorimeter
(Item 11) (Sub .05) (CC)
E41 on Laboratory Apparatus
(#10-01)
REVISION
OF STANDARD
E
288-2006, Specification for Laboratory Glass Volumetric Flasks (Item
1) (Sub .01) (CC)
REAPPROVAL
OF STANDARD
E
671-1998(2004), Specification for Maximum Permissible Thermal Residual Stress
in Annealed Glass Laboratory Apparatus
(Item 2) (Sub .01)
E
677-1994(2004), Specification for Interchangeable Spherical Ground Joints (Item
3) (Sub .01)
E50 on Environmental
Assessment, Risk Management and Corrective Action (#10-01)
NEW
STANDARD
New
Standard, Guide for Basic Assessment and Management of Greenhouse Gases (Item
2) (Sub .05) (CC) (Ref. WK21808
)
REAPPROVAL
OF STANDARD
D
5746-1998(2002), Classification of Environmental Condition of Property Area
Types for Defense Base Closure and Realignment Facilities (Item
1) (Sub .02)
E54 on Homeland Security
Applications (#10-01)
NEW
STANDARD
New
Standard, Guide for Emergency Operations Center Development (Item
1) (Sub .02) (CC) (Ref. WK12954
)
F02 on Flexible Barrier
Packaging (#10-01)
NEW
STANDARD
New
Standard, Test Method for Mechanical Seal Strength Testing for Round Cups and
Bowl Containers with Flexible Peelable Lids (Item
1) (Sub .20) (CC) (Ref. WK18963
)
New
Standard, Practice for Climatic Stressing of Packaging Systems (Item
3) (Sub .50) (CC) (Ref. WK25328
)
REVISION
OF STANDARD
F
2097-2008, Guide for Design and Evaluation of Primary Flexible Packaging for
Medical Products (Item 2) (Sub .50) (CC)
F09 on Tires (#10-01)
NEW
STANDARD
New
Standard, Practice for Commercial Radial Truck-bus Tires to Establish Equivalent Test Severity Between a 1.707-M
(67.23-in) Diameter Roadwheel and a Flat Surface . (Item
2) (Sub .30) (CC) (Ref. WK19706
)
REVISION
OF STANDARD
E
1136-1993(2003), (Includes Change to Title) Specification for a Radial Standard
Reference Test Tire (Item 1) (Sub .20) (CC)
REAPPROVAL
OF STANDARD
F
724-1994A(2004), Test Method for Outdoor Evaluation of Tire Sidewall Component
Cracking Resistance (Item 3) (Sub .30)
F11 on Vacuum Cleaners
(#10-01)
NEW
STANDARD
New
Standard, Test Method for Evaluating the Sustained Air Performance and Exhaust
Emissions of Central Vacuum Cleaning Units
(Item 2) (Sub .22) (CC) (Ref.
WK14392 )
New
Standard, Test Method for Draft Test Method for Measuring the Carpet Cleaning
Effectiveness of Wet Extraction Cleaners
(Item 4) (Sub .35) (Ref. WK25459 )
New
Standard, Test Method for Measuring the Carpet Cleaning Effectiveness of Wet
Extraction Cleaners (Item 5) (Sub .35) (CC) (Ref. WK27347 )
REVISION
OF STANDARD
F
395-2003(2007), Terminology Relating to Vacuum Cleaners (Items 6,7) (Sub .91) (CC)
F
2756-2009, Test Method for Test Method for Determining Energy Consumption of
Vacuum Cleaners (Item 1) (Sub .20) (CC)
REAPPROVAL
OF STANDARD
F
1977-2004, Test Method for Determining Initial, Fractional, Filtration
Efficiency of a Vacuum Cleaner System
(Item 3) (Sub .23)
F15 on Consumer Products
(#10-03)
REVISION
OF STANDARD
F
404-2009, Consumer Safety Specification for High Chairs (Item
3) (Sub .16) (CC)
F
406-2009, Consumer Safety Specification for Non-full-size Baby Cribs/play
Yards (Items 8,9,10,11,12) (Sub .18)
(CC)
F
793-2007, Classification of Wall Covering by Use Characteristics (Item
1) (Sub .15) (CC)
F 833-2009a,
Consumer Safety Performance Specification for Carriages and Strollers (Items 4,5) (Sub .17) (CC)
F15 on Consumer Products
(#10-02)
REVISION
OF STANDARD
F
833-2009a, Consumer Safety Performance Specification for Carriages and
Strollers (Items 7,8,9) (Sub .17) (CC)
F15 on Consumer Products
(#10-03)
REVISION
OF STANDARD
F
1141-1993(2009), Specification for Wallcovering (Item
2) (Sub .15) (CC)
F
1169-2009, Specification for Full-size Baby Crib (Items 13,14,15,16,17,18,19,20,21) (Sub .18) (CC)
F15 on Consumer Products
(#10-02)
REVISION
OF STANDARD
F
1487-2007AE01, Consumer Safety Performance Specification for Playground
Equipment for Public Use (Items
11,12,13,14,15,16) (Sub .29) (CC)
F15 on Consumer Products
(#10-03)
REVISION
OF STANDARD
F
2012-2008, Consumer Safety Performance Specif
Stationary Activity Centers (Item 6) (Sub .17) (CC)
F15 on Consumer Products
(#10-02)
REVISION
OF STANDARD
F
2012-2008, Consumer Safety Performance Specif
Stationary Activity Centers (Item 10) (Sub .17) (CC)
F
2085-2009, Consumer Safety Specification for Portable Bed Rails (Item
3) (Sub .11) (CC)
F
2194-2007AE01, Test Method for Bassinets and Cradles (Item
18) (Sub .18) (CC)
F
2613-2009, Consumer Safety Specification for Childrens
Folding Chairs (Item 17) (Sub .59) (CC)
F
2640-2009, Consumer Safety Specification for Booster Seats (Items 4,5,6) (Sub .16) (CC)
F15 on Consumer Products
(#10-03)
REVISION
OF STANDARD
F
2710-2008, Consumer Safety Performance Specification for Commercial Cribs (Item
7) (Sub .57) (CC)
F17 on Plastic Piping
Systems (#10-01)
NEW
STANDARD
New
Standard, Specification for Glass Fiber Reinforced Thermoplastic Pipe (Item
2) (Sub .11) (CC) (Ref. WK11803
)
New
Standard, Specification for 12 to 30 In. [300 to 750 Mm] Annular Corrugated
Profile-wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer
Applications1 (Item 15) (Sub .62) (CC) (Ref. WK14412 )
New
Standard, Specification for 30 to 60 In. [750 to 1500 Mm] Triple Profile-wall
Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications (Item
16) (Sub .62) (CC) (Ref. WK19507
)
New
Standard, Specification for Chlorinated Poly(vinyl Chloride)/aluminum/
Chlorinated Poly(vinyl Chloride) (cpvc-al-cpvc) Composite Pressure Tubing (Item
4) (Sub .11) (CC) (Ref. WK19549
)
New
Standard, Specification for Acrylonitrile-butadiene-styrene
(abs) Plastic Pipe (metric Sdr-pr) (Item
12) (Sub .61) (CC) (Ref. WK23007
)
New
Standard, Specification for Metric-sized Crosslinked
Polyethylene (pex) Pipe Systems (Item
13) (Sub .61) (CC) (Ref. WK23064
)
New
Standard, Specification for Multilayer Polyethylene (PE) Pipe with a
Co-extruded Inner And/or Outer Polyamide (pa) Layer for Pressure Piping
Applications in Contact with Liquid Hydrocarbons (Item
3) (Sub .11) (CC) (Ref. WK23226
)
New
Standard, Specification for Polyethylene (PE) Gas Pressure Pipe with a Peelable Polypropylene (pp) Outer Layer (Item
11) (Sub .60) (CC) (Ref. WK24149
)
New
Standard, Practice for Internal Non Structural Epoxy Barrier Coating Material
Used in Pressurized Piping Systems
(Item 19) (Sub .67) (CC) (Ref.
WK24231 )
REVISION
OF STANDARD
D
2665-2009, Specification for Poly(vinyl Chloride) (PVC) Plastic Drain, Waste,
and Vent Pipe and Fittings (Item 17) (Sub .63)
D
3261-2003, Specification for Butt Heat Fusion Polyethylene Pe
Plastic Fittings for Polyethylene Pe Plastic Pipe and
Tubing (Item 1) (Sub .10)
F
610/F 610M-2000A(2009), Test Method for Evaluating the Quality of Molded
Poly(vinyl Chloride) (PVC) Plastic Pipe Fittings by the Heat Reversion
Technique (Item 9) (Sub .40)
F
2160-2008, Specification for Solid Wall High Density Polyethylene (hdpe) Conduit Based on Controlled Outside Diameter (od) (Item 6) (Sub .26) (CC)
F
2648/F 2648M-2007, Specification for 2 to 60 Inch(50 to 1500mm) Annular
Corrugated Profile Wall Polyethylene(pe) Pipe and
Fittings for Land Drainage Applications
(Item 18) (Sub .65) (CC)
REAPPROVAL
OF STANDARD
D
2152-1995(2003), Test Method for Adequacy of Fusion of Extruded Poly Vinyl
Chloride PVC Pipe and Molded Fittings by Acetone Immersion (Item
5) (Sub .25)
D
3485-2002, Specification for Smooth-wall Coilable
Polyethylene Pe Conduit Duct for Preassembled Wire
and Cable (Item 7) (Sub .26)
F
1759-1997(2004), Practice for Design of High-density Polyethylene Hdpe Manholes for Subsurface Applications (Item
8) (Sub .26)
F
2206-2002, Specification for Fabricated Fittings of Butt-fused Polyethylene Pe Plastic Pipe, Fittings, Sheet Stock, Plate Stock, or
Block Stock (Item 20) (Sub .10)
WITHDRAWAL
OF STANDARD
D
3309-1996A(2002), Specification for Polybutylene Pb Plastic Hot- and Cold-water Distribution Systems (Item
14) (Sub .61) (CC)
D
6070-2002, Test Methods for Physical Properties of Smooth-wall, Coilable, Polyethylene Pe Conduit
Duct for Preassembled Wire and Cable
(Item 10) (Sub .40) (CC)
F18 on Electrical Protective
Equipment for Workers (#10-01)
REVISION
OF STANDARD
D
178-2001(2005), Specification for Rubber Insulating Matting (Item
2) (Sub .25) (CC)
D 1048-2005,
Specification for Rubber Insulating Blankets
(Item 3) (Sub .25) (CC)
D
1049-1998(2002)E01, Specification for Rubber Insulating Covers (Item
4) (Sub .25) (CC)
F
819-2008, Terminology Relating to Electrical Protective Equipment for
Workers (Item 9) (Sub .60) (CC)
F
887-2005E01, Specifications for Personal Climbing Equipment (Item
1) (Sub .15) (CC)
F
914-2003, (Includes Change to Title) Test Method for Acoustic Emission for
Insulated and Non-insulated Aerial Personnel Devices Without Supplemental Load
Handling Attachments (Item 7) (Sub .55) (CC)
F
1430-2003E01, Test Method for Acoustic Emission Testing of Insulated and
Non-insulated Aerial Personnel Devices with Supplemental Load Handling
Attachments (Item 8) (Sub .55) (CC)
F
1742-2003E01, Specification for PVC Insulating Sheeting (Item
5) (Sub .25) (CC)
F
2320-2003, Specification for Rubber Insulating Sheeting (Item
6) (Sub .25) (CC)
F20 on Hazardous Substances
and Oil Spill Response (#10-01)
NEW
STANDARD
New
Standard, Guide for Selection of Booms for Oil-spill Response (Item
3) (Sub .11) (CC) (Ref. WK12691
)
New
Standard, Guide for In-situ Burning of Oil Spills in Marshes (Item
7) (Sub .15) (Ref. WK17360 )
REVISION
OF STANDARD
F
1737-2007, Guide for Use of Oil Spill Dispersant Application Equipment During
Spill Response Boom and Nozzle Systems
(Item 5) (Sub .13) (CC)
F
1738-1996(2007), Test Method for Determination of Deposition of Aerially
Applied Oil Spill Dispersants (Item 6) (Sub .13) (CC)
REAPPROVAL
OF STANDARD
F
962-2004, Specification for Oil Spill Response Boom Connection:
Z-connector (Item 1) (Sub .11)
F
1780-1997(2002), Guide for Estimating Oil Spill Recovery System
Effectiveness (Item 4) (Sub .12)
F
2438-2004, Specification for Oil Spill Response Boom Connection: Slide
Connector (Item 2) (Sub .11)
F42 on Additive
Manufacturing Technologies (#10-01)
REVISION
OF STANDARD
F
2792-2009E01, Terminology for Additive Manufacturing Technologies (Items 1,2) (Sub .91) (CC)
G02 on Wear and Erosion
(#10-01)
NEW
STANDARD
New
Standard, Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems
(Item 6) (Sub .50) (Ref. WK20099 )
New
Standard, Test Method for Damage to Contacting Solid Surfaces Under Fretting
Conditions (Item 2) (Sub .40) (CC) (Ref. WK22723 )
REVISION
OF STANDARD
G
40-2010, Terminology Relating to Wear and Erosion (Items 8,9) (Sub .91)
G
56-1982(2005), (Includes Change to Title) Test Method for Abrasiveness of
Ink-impregnated Fabric Printer Ribbons
(Item 1) (Sub .30) (CC)
G
73-2004, (Includes Change to Title) Practice for Liquid Impingement Erosion
Testing (Item 7) (Sub .10) (CC)
G
163-1999(2004), Guide for Digital Data Acquisition in Wear and Friction
Measurements (Item 10) (Sub .20) (CC)
REAPPROVAL
OF STANDARD
G
77-2005E01, Test Method for Ranking Resistance of Materials to Sliding Wear
Using Block-on-ring Wear Test (Item 3) (Sub .40)
G
99-2005, Test Method for Wear Testing with a Pin-on-disk Apparatus (Item
4) (Sub .40)
G
133-2005E01, Test Method for Linearly Reciprocating Ball-on-flat Sliding
Wear (Item 5) (Sub .40)
G03 on Weathering and
Durability (#10-01)
REVISION
OF STANDARD
G
151-2009, Practice for Exposing Nonmetallic Materials in Accelerated Test
Devices That Use Laboratory Light Sources
(Items 1,2) (Sub .03) (CC)
WITHDRAWAL
OF STANDARD
E
41-1992(2004), Terminology Relating to Conditioning (Item
5) (Sub .92) (CC)
G
153-2004, Practice for Operating Enclosed Carbon Arc Light Apparatus for
Exposure of Nonmetallic Materials
(Item 4) (Sub .03) (CC)
G
179-2004, Specification for Metal Black Panel and White Panel Temperature
Devices for Natural Weathering Tests
(Item 3) (Sub .02) (CC)
G04 on Compatibility and
Sensitivity of Materials in Oxygen Enriched Atmospheres (#10-01)
REVISION
OF STANDARD
G
124-1995(2003), Test Method for Determining the Combustion Behavior of Metallic
Materials in Oxygen-enriched
Atmospheres (Item
1) (Sub .01) (CC)
REAPPROVAL
OF STANDARD
G
121-1998(2004), Practice for Preparation of Contaminated Test Coupons for the
Evaluation of Cleaning Agents (Item 2) (Sub .02)