Society Review of Main Committee Ballot Actions

November 2009

Deadline for Receipt: Must be Received Before December 1, 2009

The items listed are currently being balloted by the corresponding main committee and are submitted here for review. To request copies of proposed new standards and revisions of standards for review and voting purposes only, please email socrev@astm.org and provide the following information:

 

- Your name
- Your member number
- The designation and title of the main committee of interest (e.g., A04 on Iron Castings)
- The designation of the ballot (e.g., #00-01)
- The specific item(s) (e.g., Item 22)

 

After receiving the items you’ve requested, if you would like to comment or vote negative you may submit additional correspondence to ASTM Headquarters. All comments and negatives submitted by Society members will be considered by the originating subcommittee and main committee.

 

Key:
(#00-01) = Ballot Designation #
(Sub.00) = Subcommittee Jurisdiction
(CC) = Item is being balloted concurrently by the subcommittee and main committee
(Ref. Z6287Z) = reference # for new standards that have not yet been approved

 

 Deadline for Receipt   DEC        01,   2009

A05 on Metallic-coated Iron and Steel Products (#09-04)

 

REVISION OF STANDARD

A 308/A 308M-2006, Specification for Steel Sheet, Terne Lead-tin Alloy Coated by the Hot-dip Process  (Item  1) (Sub .11)

 

A05 on Metallic-coated Iron and Steel Products (#09-03)

 

REVISION OF STANDARD

A 463/A 463M-2009, Specification for Steel Sheet, Aluminum-coated, by the Hot-dip Process  (Item  1) (Sub .11) 

A 653/A 653M-2009, Specification for Steel Sheet, Zinc-coated (galvanized) or Zinc-iron Alloy-coated (galvannealed) by the Hot-dip Process  (Item  2) (Sub .11) 

A 792/A 792M-2009, Specification for Steel Sheet, 55 % Aluminum-zinc Alloy-coated by the Hot-dip Process  (Item  3) (Sub .11) 

A 875/A 875M-2009, Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-coated by the Hot-dip Process  (Item  4) (Sub .11) 

A 924/A 924M-2009, Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-dip Process  (Item  5) (Sub .11) 

A 1046/A 1046M-2006, Specification for Steel Sheet, Zinc-aluminum-magnesium Alloy-coated by the Hot-dip Process  (Item  6) (Sub .11) 

 

A05 on Metallic-coated Iron and Steel Products (#09-04)

 

REAPPROVAL OF STANDARD

A 1004/A 1004M-1999(2004), Practice for Establishing Conformance to the Minimum Expected Corrosion Characteristics of Metallic, Painted-metallic, and Non-metallic Coated Steel Sheet Intended for Use as Cold Formed Framing Members  (Item  2) (Sub .11) 

 

B07 on Light Metals and Alloys (#09-05)

 

REVISION OF STANDARD

B 211-2003, Specification for Aluminum and Aluminum-alloy Bar, Rod, and Wire  (Item  2) (Sub .03) (CC)

B 211M-2003, Specification for Aluminum and Aluminum-alloy Bar, Rod, and Wire Metric  (Item  8) (Sub .03) (CC)

B 557-2006, Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-alloy Products  (Item  6) (Sub .05) (CC)

B 557M-2007E01, Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-alloy Products (metric)  (Item  7) (Sub .05) (CC)

B 594-2006, Practice for Ultrasonic Inspection of Aluminum-alloy Wrought Products for Aerospace Applications  (Item  3) (Sub .03) (CC)

B 926-2003, Method for Pinhole Determination in Aluminum and Aluminum Alloy Plain Foil by Means of a Light Table  (Item  4) (Sub .03) (CC)

 

REAPPROVAL OF STANDARD

B 548-2003, Test Method for Ultrasonic Inspection of Aluminum-alloy Plate for Pressure Vessels  (Item  5) (Sub .03) 

 

C01 on Cement (#09-02)

 

REVISION OF STANDARD

C 114-2009, Test Methods for Chemical Analysis of Hydraulic Cement  (Items 4,5,6,7,8,9,10) (Sub .23) 

C 115-1996A(2003), Test Method for Fineness of Portland Cement by the Turbidimeter  (Item  11) (Sub .25) (CC)

C 188-1995(2003), Test Method for Density of Hydraulic Cement  (Item  12) (Sub .25) (CC)

C 204-2007, Test Methods for Fineness of Hydraulic Cement by Air-permeability Apparatus  (Item  13) (Sub .25) (CC)

C 219-2007a, Terminology Relating to Hydraulic Cement  (Items 18,19,20) (Sub .91) (CC)

C 465-2009, Specification for Processing Additions for Use in the Manufacture of Hydraulic Cements  (Item  2) (Sub .20) (CC)

C 490-2008, Practice for Use of Apparatus for the Determination of Length Change of Hardened Cement Paste, Mortar, and Concrete  (Item  21) (Sub .95) 

C 596-2007, Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement  (Item  17) (Sub .31) (CC)

C 786-1996(2003), Test Method for Fineness of Hydraulic Cement and Raw Materials by the 300-um No. 50 , 150-um No. 100 , and 75-um No. 200 Sieves by Wet Methods  (Item  14) (Sub .25) (CC)

C 1005-2005, Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements  (Item  22) (Sub .95) 

C 1012-2004, Test Method for Length Change of Hydraulic-cement Mortars Exposed to a Sulfate Solution  (Item  16) (Sub .29) (CC)

C 1506-2008, Test Method for Water Retention of Hydraulic Cement-based Mortars and Plasters  (Item  3) (Sub .22) 

C 1702-2009, Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry  (Item  15) (Sub .26) (CC)

 

C07 on Lime (#09-04)

 

REAPPROVAL OF STANDARD

C 5-2003, Specification for Quicklime for Structural Purposes  (Item  1) (Sub .02) 

C 206-2003, Specification for Finishing Hydrated Lime  (Item  2) (Sub .02) 

C 977-2003, Specification for Quicklime and Hydrated Lime for Soil Stabilization  (Item  3) (Sub .02) 

C 1164-1992(2003), Practice for Evaluation of Limestone or Lime Uniformity from a Single Source  (Item  4) (Sub .05) 

 

C08 on Refractories (#09-03)

 

REVISION OF STANDARD

C 198-2002(2008), Test Method for Cold Bonding Strength of Refractory Mortar  (Item  1) (Sub .01) (CC)

 

C09 on Concrete and Concrete Aggregates (#09-04)

 

NEW STANDARD

New Standard, Test Method for Obtaining and Testing Specimens of Hardened Lightweight Insulating Concrete for Compressive Strength  (Item  2) (Sub .21)  (FORMERLY C0513-1989(1995)          )

New Standard, Specification for Reactive Methacrylate Bonding Systems for Concrete  (Item  4) (Sub .25)  (Ref. WK24405    )

 

REVISION OF STANDARD

C 29/C 29M-2007, Test Method for Bulk Density (unit Weight) and Voids in Aggregate  (Item  1) (Sub .20) 

C 125-2007, Terminology Relating to Concrete and Concrete Aggregates  (Item  19) (Sub .91) 

C 387/C 387M-2009, Specification for Packaged, Dry, Combined Materials for Mortar and Concrete  (Item  9) (Sub .43) 

C 418-2005, Test Method for Abrasion Resistance of Concrete by Sandblasting  (Item  12) (Sub .62) (CC)

C 597-2002, Test Method for Pulse Velocity Through Concrete  (Items 13,14,15,16) (Sub .64) (CC)

C 637-1998A(2003), Specification for Aggregates for Radiation-shielding Concrete  (Item  5) (Sub .41) 

C 638-1992(2002), Descriptive Nomenclature of Constituents of Aggregates for Radiation-shielding Concrete  (Item  6) (Sub .41) 

C 928/C 928M-2008, Specification for Packaged, Dry, Rapid-hardening Cementitious Materials for Concrete Repairs  (Item  10) (Sub .43) (CC)

C 1077-2009b, Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation  (Items 20,21) (Sub .98) (CC)

C 1107/C 1107M-2008, Specification for Packaged Dry, Hydraulic-cement Grout (nonshrink)  (Item  11) (Sub .43) 

C 1240-2005, Specification for Silica Fume Used in Cementitious Mixtures  (Item  3) (Sub .24) 

C 1543-2002, Test Method for Determining the Penetration of Chloride Ion Into Concrete by Ponding  (Items 17,18) (Sub .66) 

C 1609/C 1609M-2007, Test Method for Flexural Performance of Fiber-reinforced Concrete (using Beam with Third-point Loading)  (Items 7,8) (Sub .42) (CC)

 

C11 on Gypsum and Related Building Materials and Systems (#09-05)

 

REVISION OF STANDARD

C 11-2008c, Terminology Relating to Gypsum and Related Building Materials and Systems  (Item  6) (Sub .91) 

 

C11 on Gypsum and Related Building Materials and Systems (#09-06)

 

REVISION OF STANDARD

C 926-2006, Specification for Application of Portland Cement-based Plaster  (Item  1) (Sub .03) (CC)

C 1063-2008, Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster  (Item  2) (Sub .03) (CC)

 

C11 on Gypsum and Related Building Materials and Systems (#09-05)

 

REVISION OF STANDARD

C 1063-2008, Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster  (Items 1,2,3,4,5) (Sub .03) (CC)

 

C12 on Mortars and Grouts  for Unit Masonry (#09-03)

 

NEW STANDARD

New Standard, Specification for Mortars for the Repair of Histroic Masonry  (Item  3) (Sub .03) (CC) (Ref. WK5619     )

 

REVISION OF STANDARD

C 780-2009, Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry  (Item  1) (Sub .02) 

C 1019-2009, Test Method for Sampling and Testing Grout  (Item  2) (Sub .02) 

 

C15 on Manufactured Masonry Units (#09-02)

 

NEW STANDARD

New Standard, Specification for Adhered Manufactured Stone Masonry Veneer (amsmv) Units  (Item  24) (Sub .11) (CC) (Ref. WK12802    )

 

REVISION OF STANDARD

C 34-2003, Specification for Structural Clay Load-bearing Wall Tile  (Item  1) (Sub .02) 

C 55-2006E01, Specification for Concrete Building Brick  (Item  4) (Sub .03) 

C 56-2005, Specification for Structural Clay Non-load-bearing Tile  (Item  2) (Sub .02) 

C 140-2009, Test Methods for Sampling and Testing Concrete Masonry Units and Related Units  (Items 5,6) (Sub .03) 

C 744-2008, Specification for Prefaced Concrete and Calcium Silicate Masonry Units  (Item  7) (Sub .03) 

C 1088-2009, Specification for Thin Veneer Brick Units Made from Clay or Shale  (Item  3) (Sub .02) 

C 1093-2008, Practice for Accreditation of Testing Agencies for Masonry  (Item  18) (Sub .07) 

C 1232-2009a, Terminology of Masonry  (Items 19,20,21,22) (Sub .08) 

C 1262-2008a, Test Method for Evaluating the Freeze-thaw Durability of Dry-cast Segmental Retaining Wall Units and Related Concrete Units  (Items 8,9) (Sub .03) 

C 1314-2007, Test Method for Compressive Strength of Masonry Prisms  (Items 12,13) (Sub .04) 

C 1372-2004E02, Specification for Dry-cast Segmental Retaining Wall Units  (Item  10) (Sub .03) 

C 1552-2009, Practice for Capping Concrete Masonry Units, Related Units and Masonry Prisms for Compression Testing  (Item  14) (Sub .04) 

C 1601-2009, Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces  (Item  15) (Sub .04) 

C 1634-2006, Specification for Concrete Facing Brick  (Item  11) (Sub .03) 

C 1715-2009, Test Method for Evaluation of Water Leakage Performance of Masonry Wall Drainage Systems  (Items 16,17) (Sub .04) 

 

WITHDRAWAL OF STANDARD

C 1555-2003a, Practice for Autoclaved Aerated Concrete Masonry  (Item  23) (Sub .10) (CC)

 

C24 on Building Seals and Sealants (#09-02)

 

REVISION OF STANDARD

C 794-2006, Test Method for Adhesion-in-peel of Elastomeric Joint Sealants  (Item  4) (Sub .30) (CC)

C 834-2005, Specification for Latex Sealants  (Item  5) (Sub .10) (CC)

C 1311-2002, Specification for Solvent Release Sealants  (Item  1) (Sub .10) (CC)

C 1442-2006, Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus  (Item  3) (Sub .40) (CC)

 

REAPPROVAL OF STANDARD

C 1392-2000(2005), Guide for Evaluating Failure of Structural Sealant Glazing  (Item  2) (Sub .10) 

 

D01 on Paint and Related Coatings, Materials, and Applications (#09-04)

 

NEW STANDARD

New Standard, Guide for Artists' Paint Waste Disposal in Private, Non-commercial Settings  (Item  29) (Sub .57)  (Ref. WK10224    )

New Standard, Guide for Artists' Paint Waste Disposal in Smaller Commercial or Educational Settings  (Item  30) (Sub .57)  (Ref. WK10225    )

New Standard, Test Method for Determination of Zirconium Treatment Weight or Thickness on Metal Substrates by X-ray Fluorescence  (Item  26) (Sub .53) (CC) (Ref. WK17368    )

New Standard, Guide for Ft-ir Fingerprinting of a Non-aqueous Liquid Paint as Supplied in the Manufacturer's Container  (Item  1) (Sub .21) (CC) (Ref. WK24081    )

 

REVISION OF STANDARD

D 1155-1989, Test Method for Roundness of Glass Spheres  (Item  19) (Sub .44) (CC)

D 1214-2004, Test Method for Sieve Analysis of Glass Spheres  (Item  20) (Sub .44) (CC)

D 1718-2003, Specification for Isobutyl Acetate 95 Grade  (Item  8) (Sub .35) (CC)

D 3130-2003, Specification for  (Item  9) (Sub .35) (CC)

D 4360-2003, Specification for Methyl  (Item  12) (Sub .35) (CC)

D 5181-2004, Test Method for Abrasion Resistance of Printed Matter by the Ga-cat Comprehensive Abrasion Tester  (Item  28) (Sub .56) 

D 5399-2004(2009), Test Method for Boiling Point Distribution of Hydrocarbon Solvents by Gas Chromatography  (Item  13) (Sub .35) (CC)

D 6943-2003, Practice for Immersion Testing of Industrial Protective Coatings  (Item  22) (Sub .46) (CC)

D 7055-2004, Practice for Preparation by Abrasive Blast Cleaning of Hot-rolled Carbon Steel Panels for Testing of Coatings  (Item  23) (Sub .46) (CC)

D 7376-2007, Practice for Outdoor Evaluation of Wet Stack Storage Conditions on Coil-coated Metals  (Item  25) (Sub .53) (CC)

 

REAPPROVAL OF STANDARD

D 154-1985(2001), Guide for Testing Varnishes  (Item  3) (Sub .33) 

D 3329-2003, Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography  (Item  10) (Sub .35) 

D 3893-2003, Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography  (Item  11) (Sub .35) 

D 4062-1999(2003), Test Method for Leveling of Paints by Draw-down Method  (Item  14) (Sub .42) 

D 4142-1989(2001), Guide for Testing Epoxy Resins  (Item  4) (Sub .33) 

D 4143-1989(2001), Guide for Testing Latex Vehicles  (Item  5) (Sub .33) 

D 4640-1986(2001), Test Method for Determining Stroke Cure Time of Thermosetting Phenol-formaldehyde Resins  (Item  6) (Sub .33) 

D 4958-1997(2004), Test Method for Comparison of the Brush Drag of Latex Paints  (Item  15) (Sub .42) 

D 5043-2004, Practice for Field Identification of Coatings  (Item  21) (Sub .46) 

D 5150-1992(2003), Test Method for Hiding Power of Architectural Paints Applied by Roller  (Item  16) (Sub .42) 

D 5326-1994A(2002), Test Method for Color Development in Tinted Latex Paints  (Item  17) (Sub .42) 

D 6419-2000(2005), Test Method for Volatile Content of Sheet-fed and Coldset Web Offset Printing Inks  (Item  27) (Sub .56) 

D 7072-2004, Practice for Evaluating Accelerated Efflorescence of Latex Coatings  (Item  18) (Sub .42) 

 

WITHDRAWAL OF STANDARD

D 360-1989(2001), Specification for Shellac Varnishes  (Item  7) (Sub .33) (CC)

D 868-1985(2003), Test Method for Evaluating Degree of Bleeding of Traffic Paint  (Item  33) (Sub .44) (CC)

D 913-2003E01, Test Method for Evaluating Degree of Resistance to Wear of Traffic Paint  (Item  34) (Sub .44) (CC)

D 969-1985(2003)E01, Test Method for Laboratory Determination of Degree of Bleeding of Traffic Paint  (Item  35) (Sub .44) (CC)

D 3259-1995(2001)E01, Practice for Infrared Determination of the Temperature of Applied Coatings on Wood Products During the Curing Cycle  (Item  24) (Sub .52) (CC)

D 3730-2003, Guide for Testing High-performance Interior Architectural Wall Coatings  (Item  31) (Sub .42) (CC)

D 4417-2003, Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel  (Item  36) (Sub .46) (CC)

D 5146-2003, Guide to Testing Solvent-borne Architectural Coatings  (Item  32) (Sub .42) (CC)

D 6899-2003, Guide for Laboratory Cyclic Corrosion Testing of Automotive Painted Steel  (Item  2) (Sub .27) (CC)

 

D02 on Petroleum Products and Lubricants (#09-07)

 

NEW STANDARD

New Standard, Guide for Measurement of Remaining Primary Antioxidant Content in In-serive Industrial Lubricating Oils by Linear Sweep Voltammetry  (Item  44) (Sub .09) (CC) (Ref. WK13581    )

New Standard, Test Method for Determination of Free and Total Glycerin in Biodiesel Blends by Anion  Exchange Chromatography  (Item  27) (Sub .04) (CC) (Ref. WK22309    )

New Standard, Test Method for Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-duty Trucks in Sequence Vid Spark Ignition Engine  (Item  1) (Sub .b0)  (Ref. WK23347    )

New Standard, Specification for Grade 94 Unleaded Aviation Gasoline Certification and Test Fuel  (Item  22) (Sub .j0)  (Ref. WK24097    )

New Standard, Test Method for Determination of Fuel Dilution for In-service Engine Oils by Gas Chromatography  (Item  50) (Sub .96)  (Ref. WK24171    )

New Standard, Test Method for Determining Fretting Wear Resistance of Lubricating Greases Under High Hertzian Contact Pressures Using a High-frequency, Linear-oscillation (srv) Test Machine  (Item  11) (Sub .g0)  (Ref. WK24720    )

New Standard, Test Method for Standard Test Method for the Automatic Particle Counting of Lubricating and Hydraulic Fluids Using Dilution Techniques to Eliminate the Contribution of Water and Interfering Soft Particles by  (Item  51) (Sub .96)  (Ref. WK24736    )

New Standard, Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester  (Item  49) (Sub .96)  (Ref. WK24966    )

 

REVISION OF STANDARD

C 709-2006, Terminology Relating to Manufactured Carbon and Graphite  (Item  10) (Sub .f0) (CC)

D 87-2007a, Test Method for Melting Point of Petroleum Wax (cooling Curve)  (Item  45) (Sub .10) 

D 93-2008, Test Methods for Flash Point by Pensky-martens Closed Cup Tester  (Items 37,38,39,40,41) (Sub .08) 

D 664-2009, Test Method for Acid Number of Petroleum Products by Potentiometric Titration  (Items 34,35) (Sub .06) 

D 892-2006E01, Test Method for Foaming Characteristics of Lubricating Oils  (Item  36) (Sub .06) (CC)

D 975-2009b, Specification for Diesel Fuel Oils  (Items 2,3) (Sub .e0) 

D 1655-2009, Specification for Aviation Turbine Fuels  (Items 12,13,14,15,16) (Sub .j0) (CC)

D 2156-2008, Test Method for Smoke Density in Flue Gases from Burning Distillate Fuels  (Item  4) (Sub .e0) 

D 2624-2007a, Test Methods for Electrical Conductivity of Aviation and Distillate Fuels  (Item  17) (Sub .j0) 

D 2885-2009, Test Method for Determination of Octane Number of Spark-ignition Engine Fuels by On-line Direct Comparison Technique  (Item  24) (Sub .01) 

D 3240-2005, Test Method for Undissolved Water in Aviation Turbine Fuels  (Item  18) (Sub .j0) (CC)

D 3699-2008, Specification for Kerosine  (Item  5) (Sub .e0) 

D 3825-1990(2005), Test Method for Dynamic Surface Tension by the Fast-bubble Technique  (Item  46) (Sub .11) (CC)

D 3948-2008, Test Method for Determining Water Separation Characteristics of Aviation Turbine Fuels by Portable Separometer  (Item  19) (Sub .j0) (CC)

D 4054-1993(2003), Practice for Evaluating the Compatibility of Additives with Aviation-turbine Fuels and Aircraft Fuel System Materials  (Item  23) (Sub .j0) 

D 4636-1999(2004)E01, Test Method for Corrosiveness and Oxidation Stability of Hydraulic Oils, Aircraft Turbine Engine Lubricants, and Other Highly Refined Oils  (Item  43) (Sub .09) (CC)

D 4737-2009, Test Method for Calculated Cetane Index by Four Variable Equation  (Items 6,7) (Sub .e0) 

D 5291-2002(2007), Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants  (Item  25) (Sub .03) 

D 5709-1995(2005), Test Method for Sieve Analysis of Petroleum Coke  (Item  28) (Sub .05) 

D 6045-2004, Test Method for Color of Petroleum Products by the Automatic Tristimulus Method  (Item  29) (Sub .05) 

D 6079-2004E01, Test Method for Evaluating Lubricity of Diesel Fuels by the High-frequency Reciprocating Rig Hfrr  (Item  8) (Sub .e0) (CC)

D 6376-2006, Test Method for Determination of Trace Metals in Petroleum Coke by Wavelength Dispersive X-ray Fluorescence Spectroscopy  (Item  30) (Sub .05) 

D 6751-2009, Specification for Biodiesel Fuel Blend Stock (b100) for Middle Distillate Fuels  (Item  9) (Sub .e0) 

D 6756-2009, Test Method for Determination of the Red Dye Concentration and Estimation of the ASTM Color of Diesel Fuel and Heating Oil Using a Portable Visible Spectrophotometer  (Item  31) (Sub .05) 

D 7039-2007, (Includes Change to Title) Test Method for Sulfur in Gasoline and Diesel Fuel by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry  (Item  26) (Sub .03) (CC)

D 7061-2006, Test Method for Measuring N-heptane Induced Phase Separation of Asphaltene-containing Heavy Fuel Oils as Separability Number by an Optical Scanning Device  (Item  52) (Sub .14) 

D 7112-2005a, Test Method for Determining Stability and Compatibility of Heavy Fuel Oils and Crude Oils by Heavy Fuel Oil Stability Analyzer Optical Detection  (Item  48) (Sub .14) 

D 7223-2005, Specification for Aviation Certification Turbine Fuel  (Item  20) (Sub .j0) 

D 7224-2008, Test Method for Determining Water Separation Characteristics of Kerosine-type Aviation Turbine Fuels Containing Additives by Portable Separometer  (Item  21) (Sub .j0) (CC)

 

REAPPROVAL OF STANDARD

D 5443-2004, Test Method for Paraffin, Naphthene, and Aromatic Hydrocarbon Type Analysis in Petroleum Distillates Through 200 Deg;c by Multi-dimensional Gas Chromatography  (Item  47) (Sub .04) 

D 7058-2004, Test Method for Determination of the Red Dye Concentration and Estimation of Saybolt Color of Aviation Turbine Fuels and Kerosine Using a Portable Visible Spectrophotometer  (Item  32) (Sub .05) 

D 7094-2004, Test Method for Flash Point by Modified Continuously Closed Cup (mcccfp) Tester  (Item  42) (Sub .08) 

D 7095-2004, Test Method for Rapid Determination of Corrosiveness to Copper from Petroleum Products Using a Disposable Copper Foil Strip  (Item  33) (Sub .05) 

 

D04 on Road and Paving Materials (#09-03)

 

NEW STANDARD

New Standard, Practice for Evaluating Retroreflective Pavement Markings Using Portable Hand-operated Instruments  (Item  11) (Sub .38) (CC) (Ref. WK19195    )

 

REVISION OF STANDARD

D 946-2009, Specification for Penetration-graded Asphalt Cement for Use in Pavement Construction  (Item  12) (Sub .40) (CC)

D 1139-2000(2004), Specification for Aggregate for Single or Multiple Bituminous Surface Treatments  (Item  23) (Sub .50) (CC)

D 1560-2009, Test Methods for Resistance to Deformation and Cohesion of Bituminous Mixtures by Means of Hveem Apparatus  (Items 1,2) (Sub .20) (CC)

D 2493-2001E01, Standard Viscosity-temperature Chart for Asphalts  (Item  18) (Sub .44) (CC)

D 3381-2009, Specification for Viscosity-graded Asphalt Cement for Use in Pavement Construction  (Item  13) (Sub .40) (CC)

D 3666-2009, Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials  (Items 21,22) (Sub .95) 

D 4311-2004E01, Practice for Determining Asphalt Volume Correction to a Base Temperature  (Item  14) (Sub .40) (CC)

D 5167-2003, Practice for Melting of Hot-applied Joint and Crack Sealant and Filler for Evaluation  (Item  10) (Sub .33) (CC)

D 5360-2005, Practice for Design and Construction of Bituminous Surface Treatments  (Item  5) (Sub .24) 

D 6752-2003E01, Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method  (Item  3) (Sub .21) 

D 6857-2003, Test Method for Maximum Specific Gravity and Density of Bituminous Paving Mixtures Using Automatic Vacuum Sealing Method  (Item  4) (Sub .21) 

 

REAPPROVAL OF STANDARD

D 20-2003, Test Method for Distillation of Road Tars  (Item  15) (Sub .43) 

D 345-2002, Test Method for Sampling and Testing Calcium Chloride for Roads and Structural Applications  (Item  8) (Sub .31) 

D 632-2001, Specification for Sodium Chloride  (Item  9) (Sub .31) 

D 1665-1998(2003), Test Method for Engler Specific Viscosity of Tar Products  (Item  16) (Sub .43) 

D 2728-1998(2003), Practice for Paving Uses and Application Temperatures for Road Tars  (Item  17) (Sub .43) 

D 4125-2005, Test Methods for Asphalt Content of Bituminous Mixtures by the Nuclear Method  (Item  6) (Sub .25) 

D 4460-1997(2005), Practice for Calculating Precision Limits Where Values Are Calculated from Other Test Methods  (Item  19) (Sub .94) 

D 6307-2005, Test Method for Asphalt Content of Hot-mix Asphalt by Ignition Method  (Item  7) (Sub .25) 

D 6607-2000(2005), Practice for Inclusion of Precision Statement Variation in Specification Limits  (Item  20) (Sub .94)

 

D06 on Paper and Paper Products (#09-02)

 

WITHDRAWAL OF STANDARD

D 689-2003, Test Method for Internal Tearing Resistance of Paper  (Item  1) (Sub .92) (CC)

D 724-1999(2003), Test Method for Surface Wettability of Paper Angle-of-contact Method  (Item  2) (Sub .92) (CC)

D 726-1994(2003), Test Method for Resistance of Nonporous Paper to Passage of Air  (Item  3) (Sub .92) (CC)

D 776-1992(2001), Test Method for Determination of Effect of Dry Heat on Properties of Paper and Board  (Item  4) (Sub .92) (CC)

D 779-2003, Test Method for Water Resistance of Paper, Paperboard, and Other Sheet Materials by the Dry Indicator Method  (Item  5) (Sub .92) (CC)

D 780-1995(2003), Test Method for Printing Ink Permeation of Paper Castor Oil Test  (Item  6) (Sub .92) (CC)

D 2020-1992(2003), Test Methods for Mildew Fungus Resistance of Paper and Paperboard  (Item  7) (Sub .92) (CC)

D 2177-1999(2003), Test Method for Ink ABSorption of Blotting Paper  (Item  8) (Sub .92) (CC)

D 4250-1992(2003), Test Method for Water-holding Capacity of Bibulous Fibrous Products  (Item  9) (Sub .92) (CC)

D 5802-1995(2001), Test Method for Sorption of Bibulous Paper Products Sorptive Rate and Capacity Using Gravimetric Principles  (Item  10) (Sub .92) (CC)

 

D08 on Roofing and  Waterproofing (#09-03)

 

NEW STANDARD

New Standard, Test Method for Quantification of Air Intrusion in Low-sloped Membrane Roof Assemblies  (Item  14) (Sub .20) (CC) (Ref. WK23684    )

 

REVISION OF STANDARD

C 836-2006, Specification for High Solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course  (Item  15) (Sub .22) (CC)

C 957-2006, Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane with Integral Wearing Surface  (Item  16) (Sub .22) (CC)

D 36-2006, Test Method for Softening Point of Bitumen Ring-and-ball Apparatus  (Items 1,2,3,4,5,6,7,8) (Sub .03) (CC)

D 228-2008, Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing  (Item  18) (Sub .02) 

D 1865-1989(2002), Test Method for Hardness of Mineral Aggregate Used on Built-up Roofs  (Item  19) (Sub .03)

 

REAPPROVAL OF STANDARD

D 1864-1989(2002), Test Method for Moisture in Mineral Aggregate Used on Built-up Roofs  (Item  9) (Sub .03) 

D 6294-1998(2003), Test Method for Corrosion Resistance of Ferrous Metal Fastener Assemblies Used in Roofing and Waterproofing  (Item  13) (Sub .20) 

D 6769-2002, Guide for Application of Fully Adhered Cold Applied Prefabricated Reinforced Modified Bituminous Membrane Waterproofing Systems  (Item  17) (Sub .22) 

 

WITHDRAWAL OF STANDARD

D 3468-1999(2006)E01, Specification for Liquid-applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing  (Item  10) (Sub .18) (CC)

D 5036-1999(2005), Practice for Application of Adhered Poly Vinyl Chloride Sheet Roofing  (Item  11) (Sub .18) (CC)

D 5082-1999(2005), Practice for Application of Mechanically Attached Poly Vinyl Chloride Sheet Roofing  (Item  12) (Sub .18) (CC)

D14 on Adhesives (#09-05)

 

REVISION OF STANDARD

D 1337-2004, Practice for Storage Life of Adhesives by Viscosity and Bond Strength  (Item  1) (Sub .10) (CC)

D 1489-1997(2004), Test Method for Nonvolatile Content of Aqueous Adhesives  (Item  2) (Sub .10) (CC)

 

D16 on Aromatic Hydrocarbons and Related Chemicals (#09-03)

 

REVISION OF STANDARD

D 841-2002(2008)E01, Specification for Nitration Grade Toluene  (Items 1,2) (Sub .01) (CC)

D 848-2003, Test Method for Acid Wash Color of Industrial Aromatic Hydrocarbons  (Item  3) (Sub .01) (CC)

D 849-2005, Test Method for Copper Strip Corrosion by Industrial Aromatic Hydrocarbons  (Item  4) (Sub .01) (CC)

D 2359-2009, Specification for Refined Benzene-535  (Item  5) (Sub .01) (CC)

D 3437-2008, Practice for Sampling and Handling Liquid Cyclic Products  (Item  23) (Sub .08) (CC)

D 3438-2007, Practice for Sampling and Handling Naphthalene, Maleic Anhydride, and Phthalic Anhydride  (Item  24) (Sub .08) (CC)

D 4297-2005(2009), Practice for Sampling and Handling Bisphenol a (4,4 -isopropylidinediphenol)  (Item  25) (Sub .08) (CC)

D 4734-2008, Specification for Refined Benzene-545  (Item  6) (Sub .01) (CC)

D 4735-2002, Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography  (Items 18,19,20,21) (Sub .04) (CC)

D 5211-2007, Specification for Xylenes for P-xylene Feedstock  (Item  7) (Sub .01) (CC)

D 5471-2004E01, Specification for O-xylene 980  (Item  8) (Sub .01) (CC)

D 5606-2001(2006)E01, Specification for Toluene for Toluene Diisocyanate Tdi Feedstock  (Item  9) (Sub .01) (CC)

D 5713-2005, Test Method for Analysis of High Purity Benzene for Cyclohexane Feedstock by Capillary Gas Chromatography  (Item  10) (Sub .01) (CC)

D 5808-2009, Test Method for Determining Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry  (Item  22) (Sub .04) (CC)

D 5871-2008, Specification for Benzene for Cyclohexane Feedstock  (Item  11) (Sub .01) (CC)

D 6143-2005, Test Method for Iron Content of Bisphenol a 4,4 Prime; - Isopropylidenediphenol  (Item  17) (Sub .02) (CC)

D 7124-2008, Specification for Benzene for Use with Zeolite Based Catalysts  (Item  12) (Sub .01) (CC)

D 7185-2008, Specification for Low Toluene Low Dioxane (ltld) Benzene  (Item  13) (Sub .01) (CC)

 

REAPPROVAL OF STANDARD

D 6526-2003E01, Test Method for Analysis of Toluene by Capillary Column Gas Chromatography  (Item  14) (Sub .01) 

 

WITHDRAWAL OF STANDARD

D 853-2004, Test Method for Hydrogen Sulfide and Sulfur Dioxide Content Qualitative of Industrial Aromatic Hydrocarbons  (Item  15) (Sub .01) (CC)

D 1685-2005, Test Method for Traces of Thiophene in Benzene by Spectrophotometry  (Item  16) (Sub .01) (CC)

 

D19 on Water (#09-03)

 

NEW STANDARD

New Standard, Test Method for Determination of Diisopropyl Methylphosphonate, Ethyl Hydrogen Dimethylamidophosphate, Ethyl Methylphosphonic Acid, Isopropyl Methylphosphonic Acid, Methylphosphonic Acid in Pinacolyl Methylphosphoni  (Item  6) (Sub .06) (CC) (Ref. WK23076    )

New Standard, Test Method for Determination of Thiodiglycol in Water by Single Reaction Monitoring  Liquid Chromatography/tandem Mass Spectrometry  (Item  7) (Sub .06) (CC) (Ref. WK23077    )

New Standard, Test Method for Determination of Diethanolamine, Triethanolamine, N-methyldiethanolamiine and N-ethyldiethanolamine in Water by Single Reaction Monitoring Liquid Chromatography/tandem Mass Spectrometry  (Item  8) (Sub .06) (CC) (Ref. WK23078    )

New Standard, Test Method for Determination of Aldicarb, Carbofuran, Oxamyl and Methomyl by Liquid Chromatography /tandem Mass Spectrometry  (Item  9) (Sub .06) (CC) (Ref. WK23079    )

New Standard, Practice for Pressure Driven Membrane Separation Element/bundle Evaluation  (Item  77) (Sub .08) (CC) (Ref. WK23202    )

 

REVISION OF STANDARD

D 1129-2006AE01, Terminology Relating to Water  (Item  1) (Sub .02) (CC)

D 4327-2003, (Includes Change to Title) Test Method for Anions in Water by Chemically Suppressed Ion Chromatography  (Item  4) (Sub .05) (CC)

D 4410-2003, Terminology for Fluvial Sediment  (Item  10) (Sub .07) (CC)

D 5257-2003, Test Method for Dissolved Hexavalent Chromium in Water by Ion Chromatography  (Item  5) (Sub .05) (CC)

D 6161-2005, Terminology Used for Microfiltration, Ultrafiltration, Nanofiltration and Reverse Osmosis Membrane Processes  (Items 11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76) (Sub .08) (CC)

D 6502-2008, (Includes Change to Title) Test Method for Continuous Measurement of On-line Composite Samples of Low Level Filterable Matter (suspended Solids) and Non-filterable Matter (ionic Solids) in Process Water by X-ray Fluorescence (xrf)  (Item  3) (Sub .03) (CC)

 

REAPPROVAL OF STANDARD

D 5172-1991(2004), Guide for Documenting the Standard Operating Procedures Used for the Analysis of Water  (Item  2) (Sub .02) 

D27 on Electrical Insulating Liquids and Gases (#09-03)

 

REVISION OF STANDARD

D 3487-2008, Specification for Mineral Insulating Oil Used in Electrical Apparatus  (Item  1) (Sub .01) (CC)

 

D33 on Protective Coating and Lining Work for Power Generation Facilities (#09-02)

 

NEW STANDARD

New Standard, Error-no F-drafts for Title on File  (Item  1) (Sub .09) (CC) (Ref. WK12596    )

 

E01 on Analytical Chemistry for Metals, Ores, and Related Materials (#09-06)

 

REVISION OF STANDARD

E 1915-2007a, (Includes Change to Title) Test Methods for Analysis of Metal Bearing Ores and Related Materials by Combustion Infrared-absorption Spectrometry  (Item  3) (Sub .02) 

 

REAPPROVAL OF STANDARD

E 1172-1987(2003), Practice for Describing and Specifying a Wavelength-dispersive X-ray Spectrometer  (Item  1) (Sub .20) 

E 1507-1998(2003), Guide for Describing and Specifying the Spectrometer of an Optical Emission Direct-reading Instrument  (Item  2) (Sub .20) 

 

E06 on Performance of Buildings (#09-03)

 

NEW STANDARD

New Standard, Specification for Air Barrier Materials-medium Density Closed Cell Rigid Spray Polyurethane Foam  (Item  14) (Sub .41) (CC) (Ref. WK11197    )

 

REVISION OF STANDARD

E 2121-2008, Practice for Installing Radon Mitigation Systems in Existing Low-rise Residential Buildings  (Item  15) (Sub .41) 

E 2393-2009, Practice for On-site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers  (Items 12,13) (Sub .21) (CC)

 

E12 on Color and Appearance (#09-03)

 

NEW STANDARD

New Standard, Practice for Rectification of Spectrophotometric Bandpass Differences  (Item  4) (Sub .04) (CC) (Ref. WK23014    )

 

REVISION OF STANDARD

D 2244-2009a, Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates  (Item  3) (Sub .04) 

E 179-1996(2003), Guide for Selection of Geometric Conditions for Measurement of Reflection and Transmission Properties of Materials  (Item  2) (Sub .03) 

 

E12 on Color and Appearance (#09-04)

 

REVISION OF STANDARD

E 811-1995(2001), Practice for Measuring Colorimetric Characteristics of Retroreflectors Under Nighttime Conditions  (Item  1) (Sub .10) (CC)

 

E12 on Color and Appearance (#09-03)

 

REVISION OF STANDARD

E 1331-2004, Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry  (Item  1) (Sub .02) (CC)

E 2072-2009, Specification for Photoluminescent (phosphorescent) Safety Markings  (Items 12,13) (Sub .13) (CC)

E 2073-2009, Test Method for Photopic Luminance of Photoluminescent (phosphorescent) Markings  (Items 14,15,16,17,18) (Sub .13) (CC)

 

REAPPROVAL OF STANDARD

D 1729-1996(2003), Practice for Visual Appraisal of Colors and Color Differences of Diffusely-illuminated Opaque Materials  (Item  7) (Sub .11) 

D 2616-1996(2003), Test Method for Evaluation of Visual Color Difference with a Gray Scale  (Item  8) (Sub .11) 

E 1478-1997(2003), Practice for Visual Color Evaluation of Transparent Sheet Materials  (Item  9) (Sub .11) 

E 1499-1997(2003), Guide for Selection, Evaluation, and Training of Observers  (Item  10) (Sub .11) 

E 1808-1996(2003), Guide for Designing and Conducting Visual Experiments  (Item  11) (Sub .11) 

E 1809-2001, Test Method for Measurement of High-visibility Retroreflective-clothing Marking Material Using a Portable Retroreflectometer  (Item  6) (Sub .10) 

E 2177-2001, Test Method for Measuring the Coefficient of Retroreflected Luminance R  (Item  5) (Sub .10) 

 

E20 on Temperature Measurement (#09-05)

 

NEW STANDARD

New Standard, Guide for Calibration and Use of Thermocouple Reference Junction Probes in the Evaluation of Electronic Reference Junction Compensation Circuits  (Item  1) (Sub .04) (CC) (Ref. WK6822     )

 

E27 on Hazard Potential of Chemicals (#09-02)

 

REVISION OF STANDARD

E 1226-2005, Test Method for Pressure and Rate of Pressure Rise for Combustible Dusts  (Items 1,2,3,4,5,6,7,8) (Sub .05) (CC)

E 2021-2006, Test Method for Hot-surface Ignition Temperature of Dust Layers  (Item  9) (Sub .04) (CC)

 

E31 on Healthcare Informatics (#09-03)

 

REVISION OF STANDARD

E 1902-2002, Specification for Management of the Confidentiality and Security of Dictation, Transcription, and Transcribed Health Records  (Item  1) (Sub .15) 

E 1986-1998(2005), Guide for Information Access Privileges to Health Information  (Item  2) (Sub .25) (CC)

 

E50 on Environmental Assessment, Risk Management and Corrective Action (#09-07)

 

NEW STANDARD

New Standard, Guide for Investigation of Petroleum Underground Storage Tank System Equipment  Problems and Releases  (Item  1) (Sub .04) (CC) (Ref. WK15256    )

E53 on Property Management Systems (#09-03)

 

NEW STANDARD

New Standard, Practices for Defining Movements, Shipments, and Transfers of Tangible Property  (Item  3) (Sub .01) (CC) (Ref. WK17679    )

New Standard, Practice for Identification and Categorization of Tooling  (Item  4) (Sub .01) (CC) (Ref. WK17681    )

 

REVISION OF STANDARD

E 2132-2001(2007), Practice for Physical Inventory of Durable, Moveable Property  (Item  1) (Sub .01) (CC)

E 2306-2003, (Includes Change to Title) Practice for Utilization and Disposal of Personal Property  (Item  5) (Sub .04) (CC)

 

WITHDRAWAL OF STANDARD

E 2221-2002, Practice for Administrative Control of Property  (Item  2) (Sub .01) (CC)

 

E54 on Homeland Security Applications (#09-02)

 

NEW STANDARD

New Standard, Guide for Emergency Operations Center Development  (Item  1) (Sub .02) (CC) (Ref. WK12954    )

New Standard, Specification for Materials to Mitigate the Spread of Radioactive Contamination After a Radiological Dispersion Event  (Item  3) (Sub .03) (CC) (Ref. WK19352    )

New Standard, Guide for Responder Family Support Service  (Item  2) (Sub .02) (CC) (Ref. WK20535    )

 

F01 on Electronics (#09-03)

 

REAPPROVAL OF STANDARD

F 15-2004, Specification for Iron-nickel-cobalt Sealing Alloy  (Item  1) (Sub .03) 

 

WITHDRAWAL OF STANDARD

F 616M-1996(2003), Test Method for Measuring Mosfet Drain Leakage Current Metric  (Item  2) (Sub .11) (CC)

F 676-1997(2003), Test Method for Measuring Unsaturated Ttl Sink Current  (Item  3) (Sub .11) (CC)

F 1259M-1996(2003), Guide for Design of Flat, Straight-line Test Structures for Detecting Metallization Open-circuit or Resistance-increase Failure Due to Electromigration Metric  (Item  4) (Sub .11) (CC)

F 1260M-1996(2003), Test Method for Estimating Electromigration Median Time-to-failure and Sigma of Integrated Circuit Metallizations Metric  (Item  5) (Sub .11) (CC)

 

F04 on Medical and Surgical Materials and Devices (#09-05)

 

NEW STANDARD

New Standard, Test Method for Evaluating Knee Bearing (tibial Insert) Endurance and Deformation Under High Flexion  (Item  7) (Sub .22) (CC) (Ref. WK14915    )

New Standard, Guide for Performing the "behind-the-knee" Test (or Btk): for Evaluating the Skin Irritiation Response to Products and Materials That Come Into Repeated or Extended Contact with the Skin  (Item  15) (Sub .16) (CC) (Ref. WK22095    )

New Standard, Terminology for Relating to Medical and Surgical Materials and Devices  (Item  14) (Sub .97) (CC) (Ref. WK25756    )

 

REAPPROVAL OF STANDARD

F 86-2004, Practice for Surface Preparation and Marking of Metallic Surgical Implants  (Item  2) (Sub .12) 

F 746-2004, Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials  (Item  4) (Sub .15) 

F 1801-1997(2004), Practice for Corrosion Fatigue Testing of Metallic Implant Materials  (Item  5) (Sub .15) 

F 1875-1998(2004), Practice for Fretting Corrosion Testing of Modular Implant Interfaces: Hip Femoral Head-bore and Cone Taper Interface  (Item  6) (Sub .15) 

 

WITHDRAWAL OF STANDARD

F 921-1985(2008)E01, Terminology Relating to Hemostatic Forceps  (Item  9) (Sub .33) (CC)

F 1078-1987(2008)E01, Terminology for Surgical Scissors--inserted and Non-inserted Blades  (Item  10) (Sub .33) (CC)

F 1251-1989(2003), Terminology Relating to Polymeric Biomaterials in Medical and Surgical Devices  (Item  1) (Sub .11) (CC)

F 1582-1998(2003), Terminology Relating to Spinal Implants  (Item  8) (Sub .25) (CC)

F 1638-1995(2008)E01, Terminology for Surgical Tissue/dressing/pick-up Forceps (thumb-type)  (Item  11) (Sub .33) (CC)

F 1840-1998A(2004), Terminology for Surgical Suture Needles  (Item  12) (Sub .33) (CC)

F 2005-2005, Terminology for Nickel-titanium Shape Memory Alloys  (Item  3) (Sub .12) (CC)

F 2312-2004, Terminology Relating to Tissue Engineered Medical Products  (Item  13) (Sub .41) (CC)

 

F07 on Aerospace and Aircraft (#09-03)

 

REVISION OF STANDARD

F 1624-2006, Test Method for Measurement of Hydrogen Embrittlement Threshold in Steel by the Incremental Step Loading Technique  (Item  1) (Sub .04) (CC)

 

F08 on Sports Equipment and Facilities (#09-06)

 

NEW STANDARD

New Standard, Test Method for Evaluating Design and Performance Charactristics of Elliptical Trainers  (Item  2) (Sub .30) (CC) (Ref. WK17534    )

New Standard, Specification for Goggle- and Spectacle-type Eye Protectors for Selected Motor Sports  (Item  5) (Sub .57) (CC) (Ref. WK23632    )

New Standard, Specification for Elliptical Trainers  (Item  1) (Sub .30) (CC) (Ref. WK991      )

 

REVISION OF STANDARD

F 659-2006, (Includes Change to Title) Specification for Skier Goggles and Faceshields  (Item  3) (Sub .57) (CC)

F 803-2003, Specification for Eye Protectors for Selected Sports  (Item  4) (Sub .57) (CC)

F 1544-2004, Specification for Determining the Rating Velocities of an Archery Bow  (Item  6) (Sub .16) 

 

F14 on Fences (#09-04)

 

NEW STANDARD

New Standard, Guide for Fences Non Residential Outdoor Swimming Pools, Hot Tubs and Spas  (Item  5) (Sub .10) (CC) (Ref. Z9469Z)

New Standard, Standard Guide for the Design and Construction of Ornamental Steel Picket Fence Systems for Security Purposes  (Item  4) (Sub .50) (CC) (Ref. WK10482    )

 

F15 on Consumer Products (#09-11)

 

NEW STANDARD

New Standard, Specification for Glass Used in Horizontal Surfaces of Futniture  (Item  8) (Sub .42) (CC) (Ref. WK22334    )

 

REVISION OF STANDARD

F 404-2008, Consumer Safety Specification for High Chairs  (Items 1,2) (Sub .16) (CC)

F 963-2008, Consumer Safety Specification for Toy Safety  (Items 3,4,5,6) (Sub .22) (CC)

F 1566-2008, Test Methods for Evaluation of Innersprings, Boxsprings, Mattresses or Mattress Sets  (Item  7) (Sub .32) (CC)

F 2264-2009, Consumer Safety Specification for Non-powered Scooters  (Items 9,10,11) (Sub .52) (CC)

 

F17 on Plastic Piping Systems (#09-05)

 

NEW STANDARD

New Standard, Specification for Fiber Reinforced Thermoplastic Pipe  (Item  17) (Sub .11) (CC) (Ref. WK11803    )

New Standard, Specification for 12 to 30 In. [300 to 750 Mm] Annular Corrugated Profile-wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications  (Item  38) (Sub .62) (CC) (Ref. WK14412    )

New Standard, Specification for for Modified Stub Acme Thread Joint with Elastomeric Seal in Plastic Piping Components  (Item  1) (Sub .10) (CC) (Ref. WK14955    )

New Standard, Specification for 6 to 30 Inch (152 to 762 Mm) Polypropylene (pp) Corrugated Single Wall Pipe and Double Wall Pipe  (Item  27) (Sub .26) (CC) (Ref. WK14977    )

New Standard, Specification for Corrugated High Density Polyethylene (hdpe) Water Quality Units  (Item  28) (Sub .26) (CC) (Ref. WK18469    )

New Standard, Specification for 30 to 60 In. [750 to 1500 Mm] Triple Profile-wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications  (Item  39) (Sub .62) (CC) (Ref. WK19507    )

New Standard, Specification for 30 to 60 In. [750 to 1500 Mm] Polypropylene (pp) Triple Wall Pipe and Fittings for Non-pressure Sanitary Sewer Applications  (Item  40) (Sub .62) (CC) (Ref. WK19508    )

New Standard, Practice for Field Leak Testing of Polyethylene(pe) Pressure Piping Systems Using Gaseous Media Under Pressure (pneumatic Leak Testing)  (Item  30) (Sub .40) (CC) (Ref. WK20768    )

New Standard, Specification for Multilayer Thermoplastic and Flexible Steel Pipe and Connections  (Item  18) (Sub .11) (CC) (Ref. WK21848    )

New Standard, Specification for Acrylonitrile-butadiene-styrene (abs) Plastic Pipe (metric Sdr-pr)  (Item  36) (Sub .61) (CC) (Ref. WK23007    )

New Standard, Specification for Polyethylene (PE) Pipe with a Co-extruded Inner And/or Outer Barrier Layer for Pressue Piping Applications Applications in Contact with Liquid Hydrocarbons  (Item  19) (Sub .11)  (Ref. WK23226    )

 

REVISION OF STANDARD

D 2241-2005, Specification for Poly Vinyl Chloride PVC Pressure-rated Pipe Sdr Series  (Item  26) (Sub .25) 

D 2513-2009, Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings  (Items 33,34,35) (Sub .60) 

F 477-2008, Specification for Elastomeric Seals (gaskets) for Joining Plastic Pipe  (Item  23) (Sub .20) (CC)

F 1282-2006, Specification for Polyethylene/aluminum/polyethylene Pe-al-pe Composite Pressure Pipe  (Item  20) (Sub .11) 

F 1735-2002(2008), Specification for Poly (Vinyl Chloride)(pvc) Profile Strip for PVC Liners for Rehabilitation of Existing Man-entry Sewers and Conduits  (Item  42) (Sub .67) 

F 1807-2008, Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for Sdr9 Cross-linked Polyethylene (pex) Tubing  (Items 2,12,13) (Sub .10) (CC)

F 1865-2002A(2009), Specification for Mechanical Cold Expansion Insert Fitting with Compression Sleeve for Cross-linked Polyethylene (pex) Tubing  (Item  3) (Sub .10) 

F 1960-2009, Specification for Cold Expansion Fittings with (PEXReinforcing Rings for Use with Cross-linked Polyethylene (pex) Tubing  (Items 4,5,14) (Sub .10) (CC)

F 1961-2002a, Specification for Metal Mechanical Cold Flare Compression Fittings with Disc Spring for Crosslinked Polyethylene (PEXTubing  (Item  6) (Sub .10) 

F 1974-2008, Specification for Metal Insert Fittings for Polyethylene/aluminum/polyethylene and Crosslinked Polyethylene/aluminum/crosslinked Polyethylene Composite Pressure Pipe  (Item  7) (Sub .10) 

F 2023-2008, Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (pex) Tubing and Systems to Hot Chlorinated Water  (Item  31) (Sub .40) (CC)

F 2080-2008, Specification for Cold-expansion Fittings with Metal Compression-sleeves for Cross-linked Polyethylene (pex) Pipe  (Items 8,15,16) (Sub .10) (CC)

F 2136-2008, Test Method for Notched, Constant Ligament-stress (ncls) Test to Determine Slow-crack-growth Resistance of Hdpe Resins or Hdpe Corrugated Pipe  (Item  32) (Sub .40) (CC)

F 2159-2005, Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for Sdr9 Cross-linked Polyethylene (PEXTubing  (Item  9) (Sub .10) 

F 2418-2009, Specification for Polypropylene (pp) Corrugated Wall Stormwater Collection Chambers  (Item  41) (Sub .65) 

F 2434-2008, Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for Sdr9 Cross-linked Polyethylene (pex) Tubing and Sdr9 Cross-linked Polyethylene/aluminum/cross-linked Polyethylene (pex-al-pex) Tubing  (Item  10) (Sub .10) 

F 2620-2006, Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings  (Item  24) (Sub .20) (CC)

F 2720/F 2720M-2008, Specification for Glass Fiber Reinforced Polyethylene (pe-gf) Spiral Wound Large Diameter Pipe  (Items 21,22) (Sub .11) (CC)

F 2735-2008a, Specification for Plastic Insert Fittings for Sdr9 Cross-linked Polyethylene (pex) and Polyethylene of Raised Temperature (pe-rt) Tubing  (Item  11) (Sub .10) 

 

REAPPROVAL OF STANDARD

D 2564-2004E01, Specification for Solvent Cements for Poly Vinyl Chloride PVC Plastic Piping Systems  (Item  25) (Sub .20) 

F 1176-2001E01, Practice for Design and Installation of Underground Thermoplastic Irrigation Systems with Maximum Working Pressure of 125 Psi  (Item  37) (Sub .61) 

F 1533-2001, Specification for Deformed Polyethylene Pe Liner  (Item  29) (Sub .26) 

 

G03 on Weathering and Durability (#09-02)

 

NEW STANDARD

New Standard, Practice for Conducting Exposures in Outdoor Glass-covered Exposure Apparatus with Air Circulation  (Item  1) (Sub .02) (CC) (Ref. WK16895    )

 

REVISION OF STANDARD

G 21-1996(2002), Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi  (Item  2) (Sub .04) (CC)

G 141-2003, Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials  (Item  3) (Sub .93) (CC)

 

J01 on Joint Astm/nace Committee on Corrosion (#09-02)

 

REVISION OF STANDARD

G 31-1972(2004), (Includes Change to Title) Practice for Laboratory Immersion Corrosion Testing of Metals  (Item  1) (Sub .01) (CC)