Digital Library / Topics / Construction / All JTE

• High Performance Stucco to Optimize Moisture Management in Wood-Frame Stucco Walls
• Adhesive-Bonded Anchorage Pullout Test to Estimate In-Place Concrete Compressive Strength
• Modal Analysis, Experimental Validation, and Calibration of a Historical Masonry Minaret
• Influence of Selected Mix Design Factors on the Thermal Behavior of Lightweight Aggregate Asphalt Mixes
• Evaluating the Shear Resistance of Hot Mix Asphalt by the Direct Shear Test
• Effect of Portland Cement Fineness on ASTM C1260 Expansion
• Forensic Investigation of Mechanically Stabilized Earth (MSE) Approaches
• Comparisons of Five Computational Methods for Transverse Profiles
• Computational Modeling of the Lateral Load Transfer Capacity of Rimboard
• In situ Monitoring of Pavement Stresses on the A1 in Switzerland
• Effect of Sampling Location on the Air Void Analyzer Test Results on Concrete Pavements: Evaluation of Data from a 16 State-Pooled Fund Project
• Determination of Price Reduction Factors for Density-Deficient Asphalt Pavements
• A Simple and Effective Laboratory Test Device for Measuring Tire-Pavement Contact Pressure
• Measurements with a New Peel Adhesion Test on Waterproof Membranes Used on Concrete Bridge Decks
• Interpretation of Complex Modulus Test Results for Asphalt-Aggregate Mixes
• Hot-Box Testing of Building Envelope Assemblies—A Simplified Procedure for Estimation of Minimum Time of the Test
• Development of a New Test Method for Air Intrusion Quantification of Roofing Assemblies
• Stress History Effects on Consolidation and Permeability Behavior of Fine-Grained Soils
• Sawblade Vibration Mode Shape Measurement Using ESPI
• Measurement and Evaluation of Asphalt Concrete Thermal Expansion and Contraction
• Correlations Between Depth of Water Penetration, Chloride Permeability, and Coefficient of Chloride Diffusion in Plain, Silica Fume, and Fly Ash Cement Concretes
• Ultrasonic Testing of Concrete Structures Using Indirect Transmission
• Suitability of Dynamic and Relaxation Tests for the Evaluation of Moisture Susceptibility of Asphalt Mixtures
• Field Performance Monitoring of Repair Treatments on Joint Concrete Pavements
• Effect of Length-to-Diameter Ratio of Core Sample on Concrete Core Strength—Another Look
• Field Evaluation of Tire-Road Noise Using a New Close Proximity Method
• Moisture Buffering Capacities of Five North American Building Materials
• Characterization of Louisiana Asphalt Mixtures Using Simple Performance Tests
• New Twist-Off Method for the Evaluation of In-Situ Strength of Concrete
• A Very Early Strength Concrete for Highway Construction
• Evaluation of Friction Performance of Coarse Aggregates and Hot-Mix Asphalt Pavements
• Experimental Study for Evaluating Crack Retardation of Asphalt Concrete Overlays
• Evaluate the Simple Surface Energy of Aggregates Using the Capillary Rise Method
• Evaluation of Nonnuclear Density Tests on Hot Mix Asphalt Segregation
• Using Rolling Dynamic Deflectometer and Overlay Tester to Determine the Reflective Cracking Potential
• Relationship of Aggregate Microtexture to Asphalt Pavement Skid Resistance
• Verification and Calibration of VESYS5W Fatigue Cracking Model Using Results from Accelerated Pavement Testing
• Boundary Condition Role in Tests of Wood Compression Webs
• History and Accomplishments of the U.S. Environmental Protection Agency’s Superfund Innovative Technology Evaluation (SITE) Monitoring and Measurement Technology (MMT) Program
• Development of a Viscosity Specification for Hot-Poured Bituminous Sealants
• Pavement Deformation Characteristics underqa Repeated Aircraft Loading with Fixedqa Wander Sequence
• Characterization of Thermal Degradation ofqa Liquid Amine Anti-Strip Additives in Asphaltqa Binders Due to RTFO and PAV-Aging
• Combination of Transient Plane Source and Slug Calorimeter Measurements to Estimate the Thermal Properties of Fire Resistive Materials
• Bitumen Surface Energy Characterization byqa Inverse Gas Chromatography
• New Method for Measuring Static Segregation of Self-Consolidating Concrete
• Development of Double Edge Notched Tension (DENT) Test for Asphalt Binders
• Methodology of Assessing Testing Variation for Volumetric Quantities in Hot Mix Asphalt Production
• Laboratory-based Unified Permanent Deformation Model for Hot-Mix Asphalt Mixtures
• Dynamic Modulus of Asphalt Mixtures for Development of Korean Pavement Design Guide
• Using Nondestructive Testing Technologies to Assist in Selecting the Optimal Pavement Rehabilitation Strategy
• Statistical Correlations Between Seismic Wave Velocities and SPT Blow Counts and the Relative Density of Soils
• Towards the Development of Accelerated Methods for Assessing the Durability of Wood Plastic Composites
• Quantification of Coarse Aggregate Surface Texture Using Image Analysis
• Accelerated Diffusion Test on the Intact Rock Mass
• New Method for Testing Fiber-reinforced Polymer Rods Under Flexure
• Deicer Salt Scaling Resistance of Concrete Containing Manufactured Sands
• Missionary Ridge Fire Cost Assessment
• Effect of Quarry Production Process on Specific Gravities of Aggregates
• V-Notched Shear Specimens for the Inclined Double Notch Shear Test
• Dynamic Testing of Materials with the Rotating Disk Indirect Bar-Bar Tensile Impact Apparatus
• Effect of Antistrip Additives on Surface Free Energy Characteristics of Asphalt Binders for Moisture-Induced Damage Potential
• Column Compression Strength of Tubular Packaging Forms Made from Paper
• Analyzing the Crushing of Granular Materials by Sound Analysis Technique
• IT Projects Performance Indices and Evaluation
• Damage-Based Models for Step-Stress Accelerated Life Testing
• Characterizing the Asphalt-Aggregate Mixtures Using Rheological Properties of Asphalt Binders
• Device Harmonization to Determine Smoothness Specification for Asphalt Pavements
• The Formation Mechanism of the Factory-Roof Pattern in a Torsional Fatigue Specimen with Circumferential Notch
• Testing of Rock Climbing Anchors
• Determination of Load Damage Relationships through Accelerated Pavement Testing
• Determination of Thermal Properties of Soils in a Geotechnical Centrifuge
• Fault Detection in a Water Hydraulic Motor Using a Wavelet Transform
• Heat, Air and Moisture Transport Properties of Three North American Stuccos
• Behavior of Fiber-Reinforced Cement-Stabilized Fly Ashes
• A Laboratory Study of the Effectiveness of Various Additives on Moisture Susceptibility of Asphalt Mixtures
• A Procedure to Quantify Organic Antistrip Additives in Asphalt Binders and Mixes
• Effect of Bitumen Acid Number on Moisture Susceptibility of Asphalt Mixtures
• Effects of Steel and Tungsten Carbide Ball Indenters on Rockwell Hardness Measurements
• Vapor Permeances, Air Permeances, and Water absorption Coefficients of Building Membranes
• Hot Wire Method to Characterize the Thermal Conductivity of Particle-Filled Polymer Grouts Used in Pipe-in-Pipe Application
• Direct Shear Behavior of Carbon Fiber-Reinforced Polymer Laminates and Concrete
• Durability Effects on Flexural Behavior of Fly Ash Stabilized Limestone Aggregate
• Testing Techniques and Tools to Determine Properties of Fiber-Reinforced Rods
• Application of 3D Laser Scanning on Measuring Pavement Roughness
• Accelerated Aging on Sealants and a Quantificational Way to Evaluate the Durability
• A Study on Properties of Foamed-Asphalt-Treated Mixes
• Utilization of Steel Slag Aggregate for Road Bases
• Effects of Air Void Size Distribution, Pore Pressure, and Bond Energy on Moisture Damage
• Field and Laboratory Properties of Lime-Treated Cold In-Place Recycled Asphalt Pavements
• Performance-Based Material Evaluation of Fiber-Reinforced Polymer-Wood Interfaces in Reinforced Glulam Members
• Modeling and Calibration of a Laminating Press Prototype for Fiber-Reinforced Polymer-Glulam Billets
• California Bearing Ratio Behavior of Soil-Stabilized Class F Fly Ash Systems
• Development of a Single-Edge Notched Beam Test for Asphalt Concrete Mixtures
• Evaluation of Shear Strength Functions Based on Soil Water Characteristic Curves
• Evaluation of Stripping in Bituminous Mixtures Using Conventional and Image Processing Techniques
• Considerations in Developing a Network Pavement Inventory Friction Test Program for a State Highway Agency
• Estimation of Surface Macrotexture in Hot Mix Asphalt Concrete Pavements Using Laser Texture Data
• Medical Image Denoising Using Wavelet Thresholding
• Air Permeability of Asphalt Concrete Made with Shredded-Tire Rubber-Modified Binders and its Relationship with Porosity
• Analysis of Variability in Pay Factor Systems and Sampling Methods
• Small-Scale Modeling of Metal-Plate-Connected Wood Truss Joints
• Numerical Investigation of Joint Effect on Shock Wave Propagation in Jointed Rock Masses
• Quantification of Potentially Odorous Volatile Organic Compounds from Asphalt Binders Using Head-Space Gas Chromatography
• Effect of Class C Fly Ash on the California Bearing Ratio Behavior of Soil-Fly Ash Mixes and Layered Systems
• Shear Strength of Structural Composite Lumber Using Torsion Tests
• Determination of Thermal Properties of Asphalt Mixtures
• Influence of Pavement Surface Type on Tire/Pavement Generated Noise
• Centrifuge Modeling of Diffusion through Rock Mass
• Shear Stress/Shear Strain Relation of Wood Obtained by Asymmetric Four-Point Bending Test of Side-Tapered Specimen
• The Generalized Subtraction Correction Algorithm for Measuring Duct Leakage Using a Blower Door
• Piezoelectric Sensors for Weigh-In-Motion Systems: An Experimental Insight into Edge Effects
• Influence of Hysteretic Heating on Asphalt Fatigue Characterization
• A Phenomenological Approach to Obtaining Correlations between Accelerated and Outdoor Exposure Test Results for Organic Materials
• Load-Carrying Capacity Evaluation of Damaged Reinforced Concrete Structures by Dynamic Testing and Finite-Element Model Updating
• Quantifying the Confidence Levels of Deformation Measurements in Asphalt Concrete
• Heat, Air, and Moisture Transport Properties of Several North American Bricks and Mortar Mixes
• Comparative Statistical Analysis of Original and Aged Bituminous Material Viscosity
• Laboratory Impulse Tests for Soil-Underground Structure Interactions
• Effect of Surface Macrotexture on Skid Resistance Measurements by the British Pendulum Test
• Mechanistic-Empirical Characterization of Bonding Between Ultra-Thin White-Topping and Asphalt Pavement
• An Alternate Method to Determine Asphalt Content of Hot Mix Asphalt Using Volumetric Properties
• Estimation of Stress Field Near a Notch Root of 3-D Structures with a Few Strain Data and the Body Force Method
• Evaluation Indicator of Asphalt Mixture Rutting Susceptibility
• Parametric Study on Cement Grout and Aggregate Media for Preplaced Aggregate Grouting
• Time-Constrained Scheduling and Module Allocation for On-Line Testability in Pipelined Data Paths
• Experimental Evaluation of Longitudinal Seismic Performance of Bridge Restrainers at In-Span Hinges
• Toughness Characterization of Fiber-Reinforced Concrete: Which Standard to Use?
• Geotechnical Properties of Compressible Materials Used for Induced Trench Construction
• Evaluation of Hot Mix Asphalt Macro- and Microtexture
• Design and Performance of the HEART Wheel Load Simulator
• The Pozzolanic Effect of Fly Ash on the California Bearing Ratio Behavior of Black Cotton Soil
• Testing of Bridge Weigh-In-Motion System in a Sub-Arctic Climate
• Investigation of Effects of Testing Methods on Characterization of Asphalt Concrete
• Fault Diagnosis of Loaded Water Hydraulic Actuators by Online Testing with LabVIEW®
• A Study on the Beginning of Secondary Compression of Soils
• Influence of the Geometry of the Extrusion Die on the Melt Strength of Polymers
• Development of a Procedure to Determine the Effectiveness of Asphalt-Removing Solvents
• Explaining the Hveem Stabilometer Test: Relating R-value, S-value, and the Elastic Modulus
• In Situ Shear and Compression Tests in Ancient Stone Masonry Walls of Tuscany, Italy
• A New Facility to Simulate Simultaneous Wind and Thermal Effects on Roofing Systems
• Comparison of Fine Aggregate Uncompacted Voids Content Measured by the ASTM C 1252 and the VTM-5 Devices
• Evaluation of a Boron-Nitrogen, Phosphate-Free Fire-Retardant Treatment. Part I. Testing of Douglas-Fir Plywood per ASTM Standard D 5516-96
• Evaluation of a Boron-Nitrogen, Phosphate-Free Fire-Retardant Treatment. Part II. Testing of Small Clear Specimens per ASTM Standard D 5664-95, Methods A and B
• Evaluation of a Boron-Nitrogen, Phosphate-Free Fire-Retardant Treatment. Part III. Evaluation of Full-Size 2 by 4 Lumber per ASTM Standard D 5664-95 Method C
• Optimal Quality Characteristic Evaluation for Asphalt Mixing Plants
• Texture Measurement in Zr-2.5%Nb Pressure Tubes for Pressurized Heavy Water Reactors
• Compression Index of Clays and Silts
• Fabrication of Thermal Probes for Estimation of Soil Thermal Resistivity
• Measurement of Aggregate Texture and its Influence on Hot Mix Asphalt (HMA) Permanent Deformation
• Experimental Assessment of Materials for Indirect Surface Texturing
• Spatial and Directional Distribution of Aggregates in Asphalt Mixes
• California Bearing Ratio Behavior of Cement-Stabilized Fly Ash-Soil Mixes
• Enhancement of Asphalt Pavement Evaluation Using Monte Carlo Simulation and Accelerated Pavement Testing
• Experimental Analysis of Multiple Staple Joints in Selected Wood and Wood-Based Materials
• The Fundamental Threshold Level—a New Parameter for Predicting Cavitation Erosion Resistance
• Effect of Anisotropy on Compressive and Tensile Properties of Asphalt Mixtures
• Simulation and Prediction of Hardness Performance of Rockwell Diamond Indenters Using Finite-Element Analysis
• Experimental Evaluation of the Torsion Test for Determining Shear Strength of Structural Lumber
• Finite-Element Analysis of the Stress Distribution in a Torsion Test of Full-Size, Structural Lumber
• Fatigue Testing and Evaluation of Asphalt Binders Using the Dynamic Shear Rheometer
• Visualization of Localization in Grain Skeletons with Particle Image Velocimetry
• Investigation of Stress-Strain Relationship of Confined Concrete in Hollow Bridge Columns Using Neural Networks
• Photoelastic Evaluation of Stress Fields and Fracture During Dynamic Splitting Experiments
• Influence of Hot-Mix Asphalt Parameters on the Correction Factors of the Ignition Oven Test
• Staged Compression-Immersion Direct Shear Test on Compacted Crushed Mudstone
• On Bounding a Near-Zero Probability When Zero Occurrences Appear in a Sample
• Influence of Suction Dissipation on Compression of Compacted Rock Aggregates Due to Immersion
• Correlating Permanent Deformation Characteristics of Hot Mix Asphalt with Aggregate Geometric Irregularities
• Model-Fitting the Master Curves of the Dynamic Shear Rheometer Data to Extract a Rut-controlling Term for Asphalt Pavements
• Synthesis of Methane Hydrate in an Unconsolidated Medium
• An Apparatus for Evaluating Adhesion Between Soils and Solid Surfaces
• Measurement of Relative Surface Roughness at Particulate-Continuum Interfaces
• Quantification of Coarse Aggregate Shape and Its Effect on Engineering Properties of Hot-Mix Asphalt Mixtures
• Specimen Instrumentation Techniques for Permanent Deformation Testing of Asphalt Mixtures
• Use of n-Propyl Bromide Solvents for Extraction and Recovery of Asphalt Cements
• Stress Pattern Analysis by Thermal Emission of Plain Weave Carbon Fiber/Epoxy Resin Composite Iosipescu Specimens with Three Different Notch Angles
• Coarse Aggregate Shape and Size Properties Using a New Image Analyzer
• Superpave Shear Tester as a Simple Standardized Measure to Evaluate Aggregate-Asphalt Mixture Performance
• Model Tests by Centrifuge of Soil Nail Reinforcements
• Evaluation of the Elevated Temperature Creep Strength of Three Lead-Free Solder Alloys in Soldered Joints
• Development of New Low-Cost Indirect Tensile Test Equipment for Bituminous Mixtures
• Comparison of the Systems Approach and the Nordic Model and their Melded Application in the Development of Performance-Based Building Codes and Standards
• Formation of Shear Bands in Model Ground Composed of Aluminum Rods Beneath a Footing
• Falling Head Hydraulic Conductivity Tests in a Geotechnical Centrifuge
• Empirical Models Depicting Grain Angle Effects on Load-Embedment Response of Dowel-Type Fasteners in Wood
• The Determination of the In-Plane Shear Characteristics of Aluminum Alloys
• A Performance Evaluation of Lightweight Non-Contact Pavement Profilers
• Effect of Zeolitization on Compaction, Consolidation, and Permeation Characteristics of a Lagoon Ash
• Experimental Evaluation of the Dynamic Shear Strength of Adhesive-Bonded Lap Joints
• Liquid Limit Determination of Class F Coal Ash
• Evaluation of Density Gradients in Loaded Wheel Tester Samples
• Assessment of Misalignments in Some Selected Buildings in Jordan and Their Structural Effects
• Optimum Lime Content for Fly Ashes and the Role of the Curing Period
• Measurement of Apparent Thermal Conductivity by the Thermal Probe Method
• Development of a Multiple Linear Regression Model to Estimate the Ductile-Brittle Transition Temperature of Ferritic Low-Alloy Steels Based on the Relationship Between Small Punch and Charpy V-Notch Tests
• Fatigue and Stress Analysis of a Novel Test Coupon Geometry Developed for Hydraulic Pressure Impulse Testing
• Repeatability Analysis of Road Roughness Measurements
• Testing of Thermal Imagers for Nondestructive Thermal Testing Applications
• In Situ Measurement of Fatigue Crack Growth Rates in a Silicon Carbide Ceramic at Elevated Temperatures Using a DC Potential System
• Exterior Insulation and Finish Systems (EIFS) Use in Wood-Framed Residential Construction: Design Concepts to Avoid Common Moisture Instrusion Problems
• An Improved Capping Technique for Excavatable Controlled Low Strength Material Compressive Strength Cylinders
• Falling-Weight Deflectometer Sensor Location in the Backcalculation of Concrete Pavement Moduli
• Network-Level Pavement Deflection Testing and Structural Evaluation
• Laboratory Measurements and Analysis of Clogging Mechanism of Porous Asphalt Mixes
• Measurement of Anchor Strength in Non-Rigid Substrates
• Identifying Segregation in Hot Mix Asphalt Pavements Using Rolling Nuclear Gage Measurements and Infrared Imaging
• Precision of ASTM D 5821 Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
• Comparison and Evaluation of Tests for Coarse Aggregate Particle Shape, Angularity, and Surface Texture
• Statistical Properties of the Bukit Timah Granite in Singapore
• Effects of Silica Fume and Steel Fibers on Some Mechanical Properties of High-Strength Fiber-Reinforced Concrete
• Permeability and Consolidation Behavior of Fly Ashes
• Instability of Stacked Pallet Loads Due to Misalignment
• A New Dynamic Wind Load Cycle to Evaluate Mechanically Attached Flexible Membrane Roofs
• Development and Evaluation of a Biaxial Tensile Tester for Fabrics
• The Role of Bearing Plates in the Five-Point Bending Tests of Structural-Size Lumber
• Evaluation of Wood Poles Using a Free Vibration Technique
• Precision in the Extrapolation of Creep Rupture Data
• Water Management and Moisture Transport in Direct-Applied and EIFS Wall Assemblies
• Experimental System for Simulating Crack Propagation in Asphalt Pavements and Effectiveness of Geosynthetics in Crack Retardation
• Decay of Wood and Wood-Based Products Above Ground in Buildings
• EIFS Sealant Joint Restoration
• Extrapolation of Creep Strain Data for Pure Copper
• Effect of Asphalt Mix Design Method on Binder and Gradation Selection
• Probabilistic Model for the Analysis of Dynamic Cone Penetrometer Test Values in Pavement Structure Evaluation
• An Alternative Procedure for the Analysis of Data from the Cup Method Measurements for Determination of Water Vapor Transmission Properties
• A Testing Device for the Mechanical Characterization of Wood Beams or Plates Under Bending Compression
• The Dynamic Behavior and Vibration Monitoring of Reinforced Concrete Beams
• Stress-Strain Relationship of Common Wire Nails Under Reversed Cyclic Loading
• Establishing Uplift Design Values for Metal Connectors in Light-Frame Construction
• Measuring the Triaxial Load-Deformation Response of Orthotropic Materials Subjected to Large and Small Strain Regimes
• Role of Filter Paper Separators on the Response of Clays Under Long-Duration Sustained Loading
• Dissipated Energy of Composite Materials—Part I: Cyclic Dynamic Stress
• Durability of Geosynthetics Based on Accelerated Thermo-Oxidation Testing
• Qualitative Assessment of Failure in Bolted Connections: Maximum Stress Criterion
• Asphalt-Rubber Mixture Behavior and Design (Wet Process)
• Dynamic Calibration of Impact Test Instruments
• Variation of Resilient Modulus of Aggregate Base and Its Influence on Pavement Performance
• Stress-State Permeability Relationships for Clays with Coarse Fraction
• Studies of the Specific Gravity of Some Indian Coal Ashes
• Adapting Superpave Technology to Design of Hot Recycled Mixes
• Piezo-Actuated Microtensile Test Apparatus
• Bearing Strength of White Oak Pegs in Red Oak and Douglas Fir Timbers
• Modeling Bolted Connections in Wood: A Three-Dimensional Finite-Element Approach
• Mechanical Properties of Laminated Veneer Lumber via Five-Point Bending Test
• A Probabilistic Study of the Influence of Hanger Alignment on the Reliability of Refractory Furnace Roof Anchors
• Interlaboratory Comparison of the ASTM Standard Test Methods for Water Vapor Transmission of Materials (E 96-95)
• Compressibility Relations for Peat and Organic Soil
• Experimental Analysis of Bolted Joints in Wood
• Relating Triaxial Test Properties of Asphalt Mixtures to Mix Parameters Determined by Marshall Stability Test
• Measurement of Load Distribution in Multiple-Bolted Wood Connections
• A New Apparatus for Measuring the Drainage Properties of Porous Asphalt Mixes
• Development of a Road Roughness Profile Delineation Procedure
• New Technique for Evaluating Damping of Longitudinal Free Vibration in Wood-Based Materials
• A Methodology for the Fire Resistance Testing of Structural Components at Reduced Scale
• Symposium on International Advanced Vehicle/Transportation Infrastructure Technology
• Relationship Between Statistical Distributions of Traffic Loads and Pavement Responses
• Calibration of Weigh-in-Motion Systems Through Dynamic Vehicle Simulation
• Evaluation of Overhead and In-Ground Vehicle Detector Technologies for Traffic Flow Measurement
• First Continuous Remote Bridge Monitoring System Ensures Safe Operation of 65-Year-Old Rolling Bascule Bridge
• Determination of Thermal Properties of Pavement Materials and Unbound Aggregates by Transient Heat Conduction
• Creep Lifetime Under Constant Load and Constant Stress: Theory and Experiment
• Objective Assessment of Fabric Handle in Fabrics Treated with Flame Retardants
• The Effect of Fiber Coating on the Temperature Dependence of the Elastic and Anelastic Properties of a Fiber-Reinforced Borosilicate Glass Matrix Composite
• Accuracy of Wood Resistance Sensors for Measurement of Humidity
• Cyclic Tests on High-Strength Prestressed Concrete Frames
• Fly Ash as a Pre-Filter Material for the Retention of Lead Ions
• Time-Dependent Bending Properties of Lumber
• Empirical Determination of the Manufacturing Processes Which Affect EFP Liner Performance
• Testing and Evaluation of Metal-Plate-Connected Wood Truss Joints
• Evaluation of Test Methods and Environmental Conditions to Promote Efflorescence Formation Under Laboratory Conditions
• Precision of Marshall Stability and Flow Test Using 6-in. (152.4-mm) Diameter Specimens
• Development and Application of a Quality System Standard for Construction Materials Testing Laboratories
• Prediction of Creep Properties of Chipboard Used in Stressed-Skin Panels
• An Analysis of Hot Mix Asphalt Mat Density Measurements
• A Servo-Control System for the Universal Panel Tester
• Specimen Size Effects on the Diametrical Mechanical Testing of Cylindrical Asphalt Mixes
• Creep, Shrinkage, and Mortars in Historic Preservation
• Development of a New Accelerated Adhesion Test for Silicone Sealants
• Elastic Strain, Creep, and Recovery in Mortars: Additional Analysis
• Characterization of Base/Subbase Materials under Repetitive Loading
• Optimization of Lime Content for Fly Ash
• A Quantitative X-Ray Diffraction Technique for Analyzing Sedimentary Rocks and Soils
• Monitoring of Cement Stabilized Surrogate Waste Using Resonant Frequency Techniques
• Comparison of Optically and Mechanically Measured Deformations in a Finger-Jointed Wood Tension Specimen
• A Vibration-Based Method for Determining St. Venant Torsional and Warping Stiffnesses of Members with Open Cross-Sections
• A Universal Panel Tester
• An Analysis of Creep and Shrinkage in Mortars
• Comparison of Asphalt Contents Measured with the Nuclear Gage and Extraction Methods
• Solvent-Free, Nuclear-Free Determination of Asphalt Content and Gradation of Hot-Mix Asphalt Concrete
• An Evaluation of Several Techniques for Measuring Air-void Content in Asphalt Concrete Specimens
• Bond Tests of Fiberglass-Reinforced Plastic Bars in Concrete
• Modeling Wood in Transverse Compression
• Behavior of Wood in Transverse Compression
• Objective Evaluation of Surface Characteristics to Determine Smoothness of Pile Fabrics
• Behavior of Asphalt Concrete Mixtures in Triaxial Compression
• Determining Asphalt Concrete Properties via the Impact Resonant Method
• Testing Techniques for Measurement of Bulk Modulus
• A Computer Method of Analysis for Tire Wear Characterization, Identification, and Classification
• Techniques for the Determination of the Static and Dynamic Internal Friction Coefficients of Ceramic Powder
• Automated Data Acquisition and Load and Strain Measurement Resolution
• Pressure and Flexible Membrane Effects on Direct-Contact Extensometer Measurements in Axisymmetric Compression Tests
• Compaction of Asphalt Mixtures for Laboratory Testing: Evaluation Based on Density Profile
• Static Structural Integrity Monitoring System
• Resonance Monitoring of Building Assemblies for Durability Tests
• An Improved Moisture Permeability Measurement Method
• Compressibility Analysis of Wet Abraded Woven Fabrics
• Analysis of Marshall Test Behavior with Triaxial Test Determined Material Properties
• Infrared Technique as a Research Tool for Measuring Water Vapor Transmission of Roofing Membranes
• Flow and Stability Limits for Six-Inch-Diameter Marshall Specimens
• The Effect of Moisture on Laboratory-Prepared Asphalt Mixtures
• Superposition Theory Applied to Nail/Glue Joints in Wood: Part II—Stiffness Behavior
• Measurement of Thermal Conductivity of Refractory Bricks by the Nonsteady State Hot-Wire Method Using Differential Platinum Resistance Thermometry
• Superposition Theory Applied to Nail/Glue Joints in Wood: Part I—Strength Behavior
• An Experimental Research Program on the Behavior of Stone Masonry Structures
• Laboratory Study of Microtexture-Related Skid Resistance Characteristics of Concrete Pavement Materials
• Compression Testing of Lumber: A Comparison of Methods
• Hydrochlorofluorocarbon (HCFC) Blowing Agents for Foam Insulation of Launch Vehicle Cryogenic Propellant Tanks
• Using Microwave Measurements to Detect Moisture in Asphaltic Concrete
• Load-Slip Behavior of Nailed Joints in Seven Amazonian Hardwoods
• Introduction to Symposium on Radiation Shielding for the 21st Century
• Properties of High-Density Concrete
• Shield Verification Testing at the Idaho Chemical Processing Plant — Fuel Processing Facility
• Comparison of Fine Particle Colemanite and Boron Frit in Concrete for Time-Strength Relationship
• Test Apparatus for Simulating Interactive Loads on Metal Plate Wood Connections
• Determination of Thermal Diffusivity of Construction Materials
• Analysis of Gas-Fired Ceramic Radiant Tubes During Transient Heating: Part I—Thermal Transient Modeling
• Application of the European Yield Model to Nailed Joints in Southern Hardwoods
• Laboratory Testing of River Gravel Used in Arrester Beds
• Direct Measurements of Displacements in the Inner Roller Span of Four-Point-Bending Creep Tests
• Prediction of the Strength of Ceramic Tubular Components: Part I—Analysis
• Prediction of the Strength of Ceramic Tubular Components: Part II—Experimental Verification
• Cryogenic Creep Testing
• Design and Analysis of Jaw Crusher Gouging Abrasion Tests
• Comparison of Methods for Measuring Moisture Content of Aggregate and Asphalt-Aggregate Paving Mixtures
• A Novel Specimen Geometry for Double Shear Creep Experiments
• Mechanical Behavior of Nailed Joints with Various Side Member Materials
• Evaluation of Variability in Resilient Modulus Test Results (ASTM D 4123)
• Predicting the Durability of Paving Bricks
• Behavior of Rubber-Based Elastomeric Construction Adhesive in Wood Joints
• Instrumented Impactor for Testing Wood-Base Floor Panels
• Relationships Between the Results of Nail Impact Bend Tests and Selected Nail Material Properties
• Hardness Gradients within Roll-Threaded Steel Nails
• A Computer-Aided Image System for Analyzing Cracks Created by Nailing in Wood
• Nondestructive Testing: Interpretation of Deflection Bowl for Falling Weight Deflectometer Tests on Flexible Pavements
• Using the Aspergillus Bioassay to Detect and Measure Preservatives in Wood
• Precompressed Concrete Corbels
• Experimental Verification of a Finite Element Contact Analysis
• Predicting the Durability of Bricks
• Effects of Testing Variables on Damping and Stiffness of Nailed Wood-to-Sheathing Joints
• Additives for Bitumen in Road Construction
• Dynamic Properties of Asphalt Concrete
• Mode II Wood Test Specimen: Beam with Center Slit
• Impact Testing of Flexible Polyurethane Foams
• Granule Embedment on Shingles and Roofing Membranes
• Chimney Venting Performance Study
• Dynamic Tests on Full-Scale Structures of Glue-Laminated Timber: Theoretical and Experimental Studies
• Strength and Stiffness of Metal Railing Systems and Rails for Buildings
• Generalized Equation for Compression Ratio
• Prediction of Heat Release Rates of Surface Materials in Large-Scale Fire Tests Based on Cone Calorimeter Results
• Comparison of Severity of Exposure in ASTM E 119 and ISO 834 Fire Resistance Tests
• Basic Principles of Contaminant Transfer Modeling
• Computerization of the NBS Smoke Chamber with a Microcomputer and an A/D Converter
• A Proposed Test Procedure for the Evaluation of Air Barrier Systems
• A Suggested Methodology for the Analysis of Asphalt Age-Hardening
• Overview of the Workshop for Hot Box Operators
• An Operational Procedure for Guarded Hot Box Testing
• Design and Calibration of a Guard Added to an Existing Hot Box
• Hot Box Operating Techniques and Procedures: A Survey
• Calibration of the NBS Calibrated Hot Box
• Measuring Thermal Performance of Wall Assemblies under Dynamic Temperature Conditions
• A Comparison of Three Methods for Determining Elastic Constants of Wood
• Using an Impact Device with Sliding Drop Collar for In Situ Evaluation of Compressive Strength of Insulating Cellular Concrete
• A Suggested Role of Combustion Toxicity in Fire Risk Assessment
• In Situ Dynamic Estimates of the Equation of State for Alluvium for Intermediate Pressures and High Rates
• Effect of Bearing Plate Properties on the Behavior of Block Masonry Prisms under Axial Compression
• Measurement of Granule Coverage on Bituminous Roofing Surfaces
• Direct Modeling of Concrete Block Masonry Under Shear and In-Plane Tension
• An Empirical Model for Predicting Performance of Fire-Resistive Coatings in Wood Construction
• A Rapid Test for Asphalt Content of Bituminous Mixtures
• Optical Measurement of Granite Surface Polish
• A Method for Determining the Effect of Fasteners on the Stiffness and Strength of Wood Drive-In-Rack Pallets
• Correction of the Results of Standard Fire Resistance Tests
• A Positron Study of the Quench and Tempering Process in AISI 4340 Steel
• Temperature of the Unexposed Surface of Fire Resistance Test Specimens
• Review of ASTM Test for Surface Burning Characteristics of Building Materials (E 84) (An ASTM White Paper)
• Deckboard Bending Theory for Three-Stringer Wood Pallets in Drive-In Racks
• A Comprehensive Viscoelasto-Plastic Characterization of Sand-Asphalt Compressive and Tensile Cyclic Loading
• Evaluation of In-Situ Pavement Moduli from Deflection Measurements
• Simple Determination of the Effective Young's Modulus of Rock by the Compliance Method
• Biaxial Test Method for Characterization of Fabric Materials Used in Permanent Fabric Roof Structures
• Insulated Masonry Construction Using Knockout Web Concrete Block
• Rheology of Cold-Recycled Pavement Materials Using Creep Test
• Research into Aperture Parameters of Point-Bonded Waterproof Layers
• Comparison of Nailed Joint Test Methods
• Quantitation of Carbon in Oil Shale Process Wastewaters: Coulometry Coupled with Ultraviolet-Peroxydisulfate and High-Temperature Oxidation
• One-Dimensional Consolidation Under Linear Loading
• A Rapid Method for Determining Triuranium Octoxide (U³O⁸) by Fluorometry
• High-Speed Compression Testing at Constant True Strain Rates for Hot Working Studies
• Analysis of Nonlinear Behavior of Asphalt Concrete During Marshall Test
• Shear Transfer in Concrete and Polymer Modified Concrete Members Subjected to Shearing Loads
• Experimental Analysis and Numerical Simulation of Marshall Method of Asphalt Concrete Mix Design
• Effect of Temperature on Brick Suction
• Measuring the Abrasion of Transparent Materials with Hazemeters
• Fundamentals of Combustion Toxicology in Fire Hazard Assessment
• Erosion Behavior of Polystyrene
• Laboratory Testing of Asphalt Concrete for Porous Pavements
• Quality Control of Tests Conducted on Bituminous Mixtures in Quebec
• Void Content Prediction in Two-Size Aggregate Mixes
• The Interactions of Stabilized Scrubber Sludge and Fly Ash with the Marine Environment
• Sludge to Fertile Soil—Research Results
• Development and Correlation of a Variable-Speed Friction Tester
• Long-Time Creep-Rupture Tests of Aluminum Alloys
• A Review of Aggregate Selection Criteria for Improved Wear Resistance and Skid Resistance of Bituminous Surfaces
• Biaxial Analogs of Triaxial Stresses
• A Modified Procedure for Measuring the Maximum Specific Gravity of Bituminous Paving Mixtures
• Determining Filtration Efficiency by Comparing the Particle-Size Distribution in the Feed Stream to that in the Filtrate
• Holographic Interferometry Study of Chemical Bond of Concrete to Smooth Steel Rods
• The Particle-Size Distribution in AC Fine Test Dust
• An Indirect Tensile Test for Masonry Units
• Measurement of Linear Expansion in Bricks Due to Freezing
• Use of Pelletized Slag in Concrete Masonry Units
• The Polishing Characteristics of Common Rock Types Used as Aggregate in Bituminous Pavement Surfaces
• Effects of Dispersion and Swelling on Soil Hydraulic Conductivity
• Plastic Flow and Fracture Under Triaxial Loading
• Creep-Rupture Properties of Aluminum Alloy A356-T61
• A Study of Durability in Temperature Cycles and Water Resistance of Sulfur Concretes and Mortars
• Random Axial Loading of Short Reinforced Laterized Concrete Columns
• Preparation of Isotropically Consolidated Clay Samples with Random Fabrics
• A Method for the Determination of the Surface Area of Fine Aggregate in Bituminous Mixtures
• A Modified Fourier Method of Shape and Surface Texture Analysis of Planar Sections of Particles
• The Effect of Orientation on the Analysis of Shape and Texture of Concrete Aggregates by the Modified Fourier Method
• Concrete Core Strength—The Effect of Length to Diameter Ratio
• Shear Strength of Sand at Constant Volume
• Gypsum Content of Cements Used in Concrete Cured by Accelerated Methods
• Economic and Performance Aspects of Increasing Insulation on the Temperature of Built-Up Roofing Membranes
• Structural Strength of Short, Axially Loaded Columns of Reinforced, Laterized Concrete
• Properties of Florida-Oolite Concrete
• Behavior of Aggregate in the Washington Degradation Test
• Modification of the Thermobalance Method of Clay Determination and Analysis of Clay Mixtures
• Concept and Test Method for a Unified Characterization of the Geometric Irregularity of Aggregate Particles
• Dynamic Monitoring of Liquid Systems for Particulate Contamination
• Structural Tests of Aerodynamic Surfaces: A Systems Approach to Analysis and Design
• Correlation of Strength of Cement Mortar Cured by 28-Day Standard and Accelerated Methods
• An Evaluation of a Proposed Test Method for Determining the Maximum Dry Density of Dense Graded Aggregate
• Past, Present, and Potential Developments of Sulfate-Resisting Concretes
• Red Mud from Alumina Plants as a Possible Source of Synthetic Aggregate
• Statistical Interpretation of Strength Tests of Masonry Units for Structural Applications
• Asphalt Cements: Pen-Vis Number and Its Application to Moduli of Stiffness
• Sulfur- and Polymer-Impregnated Brick and Block Prisms
• Block Concrete Is a Structural Material
• Tensile-Shear Bond Strength and Failure Between Aggregate and Mortar
• Joint Movement in Precast Concrete Panel Cladding
• Remolding Stresses and Directional Strength Behavior of an Illitic Clay
• The Effects of Temperature and Relative Humidity on Static Strength of Hydrated Portland Cement
• Influence of Calcium Chloride on the Drying Shrinkage of Alite Paste
• Base Stabilization Using Pelletized Blast Furnace Slag
• The Effect of Water Content on the Compressive Strength of Laterized Concrete
• A Simple Technique for Determining Relative Strength of Aggregates
• Polymeric Materials for Concrete
• Early Assessment of Concrete Quality by Accelerating Compressive Strength Development with Heat (Results of ASTM's Cooperative Test Program)
• Holographic Interferometry for Measuring Swelling of Hardened Concrete
• A Simple Accelerated Strength Test for Portland Cements
• Freezing and Thawing Tests and Theories of Frost Damage
• Mechanisms of Acceleration by Calcium Chloride: A Review
• Tricalcium Silicate Hydration in the Presence of Various Salts
• Effect of Various Accelerating Chemical Admixtures on Setting and Strength Development of Concrete
• Nonlinear Viscoelastic Properties of Bituminous Concretes
• The Strength of Concrete Subjected to Compression-Compression-Tension Stress Systems
• Interlaboratory Evaluation of ASTM E 84-70 Tunnel Test Applied to Floor Coverings
• Inverse Method for Determining Approximate Stress-Strain Behavior of Soils
• An Apparatus for Two-Dimensional Measurement of the Shrinkage Resistance of Soils
• Procedures Used to Evaluate the Thermal Properties of Soils Adjacent to Buried Extra High Voltage Lines
• A New Test for Sulfate Resistance of Cements
• An Investigation of the Fluid Characteristics of Cement Grouts
• Waste Glass as Coarse Aggregate for Concrete
• Experimental Determinations of the Thermal Conductivity of Fluids by Coaxial-Cylinder Apparatus
• A Study of Cement and Concrete Correlation
• An Unconfined Direct Tension Test for Compacted Clays
• Heat Transmission in Cellulosic Fiber Insulation Materials
• The Effects of Composition and Fineness of Cement in Accelerated Testing of Concrete
• Estimation of Skid Numbers from Surface Texture Parameters in the Rational Design of Standard Reference Pavements for Test Equipment Calibration
• The Effect of Cement Properties and the Thermal Compatibility of Aggregates on the Strength of Accelerated Cured Concrete
• Mechanical Properties of Epoxy Impregnated Concrete
• Glass Transition of Asphalts Under Pressure
• A Test Procedure for Determining the Resilient Properties of Granular Materials
• A Laboratory Method of Preparing Isotropic Samples of Clay
• A Study of Currently Used Methods for Determining the Permeability of Bituminous Mixtures
• One-Dimensional Consolidation of Retarded Plastic Concrete
• Test Facilities for Measuring the Thermal Response of Materials to the Fire Environment
• Multistage Triaxial Testing of Lightly Overconsolidated Clays
• Analytical Prediction of the Thermal Response of Decomposing Materials in Fire Environments
• Armco Iron: New Concept and Broad-Data Base Justify Its Use as a Thermal Conductivity Reference Material
• The Effect of the Intermediate Principal Stress on Triaxial Fatigue of 7075-T6 Aluminum Alloy
• Mechanization for Remolding Fine Grained Soils and for the Plastic Limit Test
• Effect of Pyrolytic Temperatures on the Longitudinal Strength of Dry Douglas-Fir
• Triaxial Testing of Nonreinforced Concrete Specimens
• Obtainable Radiographic Equivalent Penetrameter Sensitivity
• Some Studies of the Influence of Localized and Gross Plasticity on the Monotonic and Cyclic Concentration Factors
• Heat Transfer in Fibrous Materials
• A Versatile Control System for Triaxial Testing of Soils
• A Microscopic Approach to the Microstructure of Paving Asphalts
• Precision of Early Shrinkage Measurements
• Some Factors Affecting Cement Mortar Strength Results Using ASTM Standard Test Methods C 348 and C 349
• The Membrane Effect in Triaxial Testing of Granular Soils
• Capillary Porosity in Hardened Cement Paste