SEDL / Topics / Iron and Steel Products / All JTE

• The Effect of Large Scale Plastic Deformation on Fatigue Crack Length Measurement with the Potential Drop Method
• A Photogrammetric System Design to Determine the Load-Deflection Behaviors of Materials in Civil Engineering
• An Evaluation of Containership Registrations in Taiwan: Application of the Grey Relation Analysis Model
• Fault Detection of Water Hydraulic Motor by Demodulated Vibration Signal Analysis with the Hilbert Transform and Genetic Algorithm
• Use of Miniature Specimen Test and Finite Element Method for Evaluation of Yield Strength and Fracture Toughness in Metallic Alloys
• Fatigue Damage Severity Calculation for Vibration Tests
• Experimental Validation of an Adjustable Railway Fastening for Slab Track
• Gray Chaos Evaluation Model for Prediction of Rolling Bearing Friction Torque
• Yield Strength Evaluation by Small-Punch Test
• Performance Evaluation of Resistance Spot Welded Interstitial Free Steel Under Cryogenic Conditions
• A Review of Solid-State Electrochemical Sensors for Measurements of Sulfur Content of Liquid Metals
• Research on the Key Technology of a Testing System of Piezomagnetic Force Transducer
• Ductile Damage Analysis for Small Punch Specimens of Type 304 Stainless Steel Based on GTN Model
• Comparison of Both Creep Resistance and Material Properties of High-Strength Low-Alloy Steel and Stainless Steel
• Improvements in the Mercury Displacement Method for Measuring Diffusible Hydrogen Contents in Steels
• A Novel Setup for Testing of Ship Deck Stiffened Panels under Axial and Lateral Loads
• FIMEC Tests on SPS sintered FeMo Ultra-Fine-Grained Alloys
• Performance Evaluation Test of the Time-of-Flight Diffraction Technique for Welded Joints of Steel Bridges
• Determination of Material Properties of Functionally Graded Plate Using the Dispersion of Guided Waves and an Artificial Neural Network
• Crack Growth Behavior in Overloaded Specimens with Sharp Notch in Low Carbon Steel
• Quantification of Constitutive Behavior of Sheet Metals Subjected to Dynamic Bulge Loading
• Comparison of Different Methods for Fatigue Limit Evaluation by Means of the Monte Carlo Method
• Hydrophilic Characterization of Automotive Brake Fluid
• Constant and Variable Amplitude Cyclic Plasticity in 316L Stainless Steel
• High-Speed Balancing of Rotors with Overhangs: When Is Overhang Likely to Cause Problems?
• On Setting Testing Rate Limitations for the Master Curve Reference Temperature, To, of ASTM E 1921
• The Response of 1CrMoV Rotor Steel to Service-Cycle Thermomechanical Fatigue Testing
• Application of the Master Curve Method and the Engineering Lower Bound Toughness Method to Laser Welded Steel
• A Procedure for Extended Extrapolation of Creep Rupture Data
• Yield Strength in Relation to Cyclic Loading
• Test Devices for Strength Measurements of Bars Under Contact Loading
• Small Punch Testing in Creep Conditions
• Finite Element Analysis and Small Punch Testing for Determining the Cryogenic Fracture Toughness of Austenitic Stainless Steel Welds
• Loss of Compression Strength in Corrugated Shipping Containers Shipped in the Single Parcel Environment
• Development of a Machine for Closely Controlled Rolling Contact Fatigue and Wear Testing
• A Methodology for Determining Rate-Dependent Flow Surfaces for Inconel 718
• Crack-Arrest Testing of Irradiated Nuclear Reactor Pressure Vessel Steels at the Oak Ridge National Laboratory
• Design and Development of a High-Speed Bearing Test Apparatus
• X-ray Piping Diagnostic System
• Ultimate Strength of Resistance Spot Welds Subjected to Combined Tension and Shear
• Low-Temperature Aging Kinetics in Cast Duplex Stainless Steels: Experimental Characterization
• Experimental Determination of the Cooling Curve for Production of Continuous-Cast Steel Billets
• Neural Network Approach for Prediction of Wrinkling Limit in Square Metal Sheet Under Diagonal Tension
• A New Approach to Measuring Transverse Properties of Structural Tubing by a Ring Test
• Corrosiveness of Chromate Exposure to Steel Embedded in Soil or Concrete
• Structure and Property Evaluation of Large-Diameter Spray-Formed Superalloy Piping
• Durability Design Process of a Vehicle Suspension Component
• A Reversing Direct Current Potential Drop System for Detecting and Sizing Fatigue Cracks along Weld Toes
• Effect of Cooling Rate Variables on the Solidification Time and Microstructure of Permanent Mold Magnesium-Treated Iron Castings
• Deformation and Fatigue Behavior of Vanadium-Based Microalloyed Forging Steel in the As-Forged and Q&T Conditions
• Proposed Test Method for Dynamic, Properties of Connections Assembled with Mechanical Fasteners
• Effects of Sample and Test Variables on Electrical Wire Insulation Flammability
• Mechanical Study of a Hypoeutectoid Steel Weld
• Wear-Related Fatigue in a Wire Rope Failure
• Study of Steel Weldments Using Electronic Speckle Pattern Interferometry
• Up-and-Down Methodology Applied to Statistically Planned Experiments
• An Experimental Appraisal of the Load-Deformation Properties of A325 High-Strength Bolts
• Characterization of Early and Modern Wire for an Italian Harpsichord
• Evaluation of Rating Numbers for Atmospheric Corrosion Resistance of Weathering Steel
• Reliability and Life Estimation from Component Fatigue Failures Below the Go-No-Go Fatigue Life Limit
• Warm Precracking at 295 K and Its Effects on the 4-K Toughness of Austenitic Steels
• Electrical Resistance Measurements on Type 304 Stainless Steel with Different Degrees of Sensitization
• Development of Methodology for Qualifying Safety Critical A286 Threaded Fasteners
• Damage Tolerance Analysis of Multiple-Site Cracks Emanating from Hole Array
• Bore Inspection and Life Evaluation of Vintage Steam Turbine/Generator Rotors
• Crevice Corrosion Testing in Natural Seawater: Significance and Use of Multiple Crevice Assemblies
• Dynamic Strain-Aging and Neutron Irradiation Effects on Mechanical and Fracture Properties of A533B Class 1 PV Steel and 2.25Cr-1Mo Steel
• An Approach to Predicting Long-Term Toughness, Strength, and Ductility of a Cr-Mo-V Steel Alloy Using Short-Term Tests
• Creep Rupture Behavior of Precorroded Carbon Steel
• A Method for Obtaining Conservative S-N Data for Welded Structures
• Localized Intrinsic Strengthening Approach (LISA): A Practical Method for Determining the Tensile Strength of Multistrand Cables
• Cryogenic Fatigue Properties of 304L and 316L Stainless Steels Compared to Mechanical Strength and Increasing Magnetic Permeability
• Diametral Strain Response and Microstructural Yielding Mechanisms of a Bainitic Pressure Vessel Steel
• Evaluation of Intergranular Fracture Initiation in Transition Region of Retired Steam Turbine Rotor Steel Using Small Specimens and the Acoustic Emission Technique
• Theory, Characteristics, and Operating Parameters of Portable Optical Emission Spectrometers for the On-Site Sorting and Identification of Steels
• Interpretive Report on the Sensitization of Type 304 Stainless Steel
• Use of X-Ray Diffraction with the Gaussian Curve Method to Evaluate the Hardening in Quenched Steels
• A Modified Metallographic Method to Detect Sensitization in Type 316 Stainless Steel
• Effect of Misalignment on the Time to Rupture
• Influence of Gage Dimensions on Elongation Values for Type 316 Stainless Steel
• The Effect of Fire Fighting Media on the Mechanical Properties of Steel Bars
• Strain Distribution Patterns During Plane Strain Compression
• Analysis of Hot Tension Test Data To Obtain Stress-Strain Curves to High Strains
• Interstitial Carbon and Nitrogen Effects on the Cryogenic Fatigue Crack Growth of AISI 304 Type Stainless Steels
• Predicting Heat-Affected Zone Hardness by the Weld Test Method
• Life Expectancy for Fossil Steam Turbine Casings after 1000 000 Hours
• Explanation of the Empirical Factor Recommended in the Permanganate Titration of High Chromium Stainless Steel from Tristumulus Chromaticity
• Damping in Turbine Blade Alloys
• Characterization of the Crack Toughness Behavior of Structural Steels by the Tearing Modulus Parameter and Acoustic Emission
• Some Aspects of Biaxial Creep Testing of Thin-Walled Cylindrical and Spherical Pressure Vessels
• Scale and Corrosion Parameters at a Geothermal Loop Experimental Facility
• Quenching, Tempering, and Aging Chromium-Molybdenum-Vanadium Cast Steels
• A Simple Test Method for the Evaluation of Tearing Modulus
• A Comparative Study of the Effect of Low Temperature on the Fracture Toughness and Cyclic Properties of Two Candidate High-Strength Low-Alloy Steels for Arctic Pipeline Applications
• An Evaluation of the Effect of Low Temperatures on Mechanical Properties of a Commercial Steel to be Used in the Arctic
• A Rapid Test for the Assessment of Steel Sheet and Tinplate Properties
• Influence of Cold Work on the In-Pile Stress Rupture Strength of 16Chromium-16Nickel-Niobium Austenitic Stainless Steels
• Holographic Examination of a Composite Pressure Vessel
• Evaluation of Intergranular Corrosion in Stainless Steel
• Nomograph for Determining Corrosion Rate in Wire Coil Tests
• Yield Point Standardization
• A High Purity Approach to High Chromium Ferritic Stainless Steels
• Programmed In Situ Melting, Freezing, and Tensile Testing for Laboratory Study of High Temperature Properties of As-Cast Metals
• Magnetomechanical Damping Properties of AISI 403 Stainless Steel with Applied Static Torsional and Axial Stresses
• The Influence of Interstitial Content on the Ductile-Brittle Transition Temperature of Fe-25Cr Ferritic Stainless Steels
• Computer Optimization of Hydraulic System Pressure for Development and Qualification Testing
• High-Temperature Properties of a High-Purity Ferritic Stainless Steel
• A Mathematical Description of the Elevated Temperature Flow Behavior of Type 304 Stainless Steel at High Strain Rates
• The Influence of Loading Variables on Environment-Enhanced Fatigue Crack Growth in High Strength Steels
• Flow and Fracture of High Strength Steels in Torsion
• Contributions of Selected Residual Elements to the Radiation Embrittlement Sensitivity of Steel Forgings
• Effect of Specimen Geometry on Hot Torsion Test Results for Solid and Tubular Specimens