|
|
|
SEDL / STP / STP856-EB
 |
STP856
Elastic-Plastic Fracture Test Methods: The User's Experience
Loss FJ, Wessel ET
Pages: 433
Published: 1985
Other books in this series
|
|
Contains research papers and discussion sections on elastic-plastic fracture toughness test methods, including J-Integral R-Curve, tear instability, and crack-tip opening displacement approaches, identifies testing problems, suggests improvements, and considers new apparatus and techniques.
Table of Contents
Introduction
Loss F., Wessel E.
Summary
Loss F., Wessel E.
Comparison of JIc Test Methods Recommended by ASTM and JSME
Kobayashi H., Nakamura H., Nakazawa H.
Welding Institute Research on the Fatigue Precracking of Fracture Toughness Specimens
Dawes M., Towers O.
The Interpretation and Analysis of Upper Shelf Toughness Data
Ingham T.
Elastic-Plastic Properties of Submerged Arc Weld Metal
Emanuelson R., Futato R., Van Der Sluys W.
A Sensitivity Study of the Unloading Compliance Single-Specimen J-Test Technique
Aadland J., Futato R., Lowe A., Van Der Sluys W.
On the Determination of Elastic-Plastic Fracture Material Parameters: A Comparison of Different Test Methods
Blauel J., Hollstein T., Voss B.
The Use of the Partial Unloading Compliance Method for the Determination of JI-R Curves and JIc
Mayville R., Voss B.
Elastic-Plastic Fracture Toughness Characteristics of Irradiated 316H Stainless Steel
Bernard J., Verzeletti G.
Effects of Strain Aging in the Unloading Compliance J Test
Domian H., Futato R., Miglin M., Van Der Sluys W.
Some Observations on J-R Curves
Druce S., Gibson G.
Experimental Observations of Ductile Crack Growth in Type 304 Stainless Steel
de Vries M., Schaap B.
Cleavage Fracture of Steel in the Ductile-Brittle Transition Region
Rosenfield A., Shetty D.
Elastic-Plastic Fracture Toughness Tests with Single-Edge Notched Bend Specimens
Anderson T., Dawes M., McHenry H.
Engineering Aspects of Crack-Tip Opening Displacement Fracture Toughness Testing
Rolfe S., Wellman G.
Alternative Displacement Procedures for J-R Curve Determination
Hiser A., Loss F.
A Comparison of Crack-Mouth Opening and Load-Line Displacement for J-Integral Evaluation Using Bend Specimens
Faucher B., Tyson W.
Determination of JIc Values by the Double Clip-on Gage Compliance Method
Akiyama T., Fujita T., Kagawa H., Urabe N.
Determining Crack Extension Using a Displacement Based Key-Curve Method
Andrews W.
J-Integral Values of Steels Tested Under Constant Load
Fujita T., Kagawa H., Urabe N., Yoshitake A.
Measurement of Stable Crack Growth Including Detection of Initiation of Growth Using the DC Potential Drop and the Partial Unloading Methods
Heerens J., Hellmann D., Knaack J., Müller-Roos J., Schwalbe K.
Comparison of Potential Drop and Unloading Compliance Methods in Determining Ductile Crack Extension
Auerkari P., Saarelma H., Saario T., Torronen K., Wallin K.
The Unloading Compliance Method for Crack Length Measurement Using Compact Tension and Precracked Charpy Specimens
Neale B., Priest R.
A DC Potential Drop Procedure for Crack Initiation and R-Curve Measurements During Ductile Fracture Tests
Bakker A.
Suggestions for a Modification of ASTM E 813
Heerens J., Schwalbe K.
Index
Committee: E08
Paper ID: STP856-EB
DOI: 10.1520/STP856-EB
ISBN-EB: 978-0-8031-4923-6
 ASTM International is a member of CrossRef.
0-8031-0419-7
978-0-8031-0419-8
STP856-EB
|
