|
|
|
SEDL / STP / STP1461-EB
 |
STP1461
Fatigue and Fracture Mechanics, 34th Volume
Daniewicz SR, Newman JC, Schwalbe KH
Pages: 584
Published: 2005
Other books in this series
|
|
37 peer-reviewed papers focus on two significant topics within damage tolerance: structural assessment and fatigue behavior in the threshold regime. Sections cover:
• Modeling of 3-D Effects on Fatigue Crack Closure Processes in Small-Scale Yielding
• Fractographic Reassessment of the Significance of Fatigue Crack Closure
• Fatigue Crack Growth Thresholds I
• Fracture Fundamentals
• Fatigue Crack Growth Thresholds II
• Integrity Assessment I
• Small Cracks I
• Integrity Assessment II
• Fatigue I
• Experimental Methods I
• Fatigue Crack Growth in the Railroad Industry
• Experimental Methods II
• Small Cracks II
• Ductile-to-Brittle Transition
• Fatigue II
• Additional Fracture Topics
• Crack Closure
• Fatigue III
Table of Contents
Modeling of Three-Dimensional Effects on Fatigue Crack Closure Processes in Small-Scale Yielding
Dodds R., Roychowdhury S.
Fractographic Reassessment of the Significance of Fatigue Crack Closure
Sunder R.
Load History Effects Resulting from Compression Precracking
James M., Forth S., Newman J.
Use of ACR Method to Estimate Closure and Residual Stress Free Small Crack Growth Data
Zonker H., Bray G., George K., Garratt M.
Influence of Temperature and Microstructure on the Fatigue Behaviour in the Threshold Regime for a Super Duplex Stainless Steel
Chai G., Hansson S.
Evaluation of the Effect of Crack Tip Constraint on Fatigue Crack Growth Rate in Inconel 718
Joyce J.
The Effect of Negative Stress Ratio Load History on High Cycle Fatigue Threshold
Golden P., Nicholas T.
Fatigue Crack Growth Rate and Stress-Intensity Factor Corrections for Out-of-Plane Crack Growth
Forth S., Herman D., James M., Johnston W.
Assessment for Decrease in Threshold Stress Intensity Factor (SIF) Range Due to High Maximum SIF
Meshii T., Ishihara K., Watanabe K.
Environmentally Influenced Fatigue in High Strength Steels
Lee E., Vasudevan A.
Selection of Material for Welded Steel Structures Based on Fracture Mechanics
Höhler S., Sedlacek G.
Assessment of Plane Stress Tearing in Terms of Various Crack Driving Parameters
Naumenko V., Volkov G.
Evaluation of Fatigue Crack Thresholds Using Various Experimental Methods
Forth S., Newman J., Forman R.
Microstructural Influences on the Development and Growth of Small Fatigue Cracks in the Near Threshold Regime
Schneider J., Kenik E.
Size Effect of Microdamage Growth and Its Relation to Macro Fatigue Life
Altus E.
On the Constraint-Based Failure Assessment of Surface Cracked Plates under Biaxial Loading
Wang X., Yu X.
An Experimental Study on Surface Crack Growth under Mode-I Load
Kim Y., Chao Y., Liu S., Jang S.
Effect of Residual Stresses on the Fatigue Crack Propagation in Welded Joints
Gubeljakme N., Predan J., Pippan R., Oblak M.
Ultrasonic Fatigue Testing of Ti-6Al-4V
Morrissey R., Golden P.
Fatigue Endurance Diagram for Materials with Defects
Kim B., Kujawski D.
Construction of J-R Curves Using the Common and Concise Formats
Donoso J., Zahr J., Landes J.
Temperature Dependent Fracture Toughness of a Single Crystal Nickel Superalloy
Bahr D., Johnson W.
Structural Reliability Analysis of Railroad Tank Cars Subjected to Fatigue and Corrosion
Zhao W., Sutton M.
Simulation of Fatigue Crack Propagation in Railway Axles
Beretta S., Carboni M.
Evaluation of the Effect of Biaxial Loading on the To Reference Temperature Using a Cruciform Specimen Geometry
Joyce J., Link R., Gaies J.
The Effect of Load Reduction Scheme on Crack Closure in the Near-Threshold Regime
Daniewicz S.
Interpretation of Material Hardness, Stress Ratio, and Crack Size Effects on the ΔKth of Small Cracks Based on Crack Closure Measurement
Kondo Y., Sakae C., Kubota M., Kashiwagi M.
Critical Assessment of the Standard ASTM E 399
Wallin K.
Sensitivity of Creep Crack Initiation and Growth in Plates to Material Properties Variations
Wasmer K., Nikbin K., Webster G.
Fretting Fatigue and Stress Relaxation Behaviors of Shot-Peened Ti-6Al-4V
Lee H., Mall S.
Analysis of Roughness-Induced Crack-Tip Shielding in Terms of Size Ratio Effect
Pokluda J., Šandera P., Horniková J.
Characterization of Crack Length Measurement Methods for Flat Fracture with Tunneling
James M., Newman J.
A New Method for Opening Load Determination from Compliance Measurements
Kujawski D., Stoychev S.
Crack Initiation, Propagation, and Arrest in 316L Model Pipe Components under Thermal Fatigue
Paffumi E., Paffumi E., Nilsson K., Taylor N., Hurst R., Bache M.
Effect of Periodic Overloads on Threshold Fatigue Crack Growth in Al-Alloys
Sunder R.
Notch-Root Elastic-Plastic Strain-Stress in Particulate Metal Matrix Composites Subjected to General Loading Conditions
Owolabi G., Singh M.
Influence of Crack-Surface Oxidation on Creep-Fatigue Crack behavior of 1Cr- and 10Cr-Steels
Mueller F., Scholz A., Berger C.
Author Index
Subject Index
Committee: E08
Paper ID: STP1461-EB
DOI: 10.1520/STP1461-EB
ISBN-EB: 978-0-8031-5505-3
 ASTM International is a member of CrossRef.
0-8031-2410-4
978-0-8031-2410-3
STP1461-EB
STP 1461
|
