|
|
|
SEDL / STP / STP1267-EB
 |
STP1267
Flammability and Sensitivity of Materials in Oxygen-Enriched Atmospheres: Seventh Volume
Janoff DD, Royals WT, Gunaji MV
Pages: 269
Published: 1995
Other books in this series
|
|
The most current information on oxygen compatibility of materials and risk management concepts and practices for oxygen systems design. Features 18 comprehensive peer-reviewed papers in the following key areas: • Test Method Development • Ignition and Combustion of Metals • Ignition and Combustion of Nonmetals • Cleaning for Oxygen Service An extensive comparison of national training courses in Medical Oxygen Administration is presented in one paper.The final paper discusses a crucial case study of an oxygen-acetylene torch failure resulting from flashback reactions.
Table of Contents
ASTM G-4 Twenty-Year Report Card: Keynote Address
Benz F.
The Seal Configuration Tester, a New Approach to the Evaluation of Elastomeric Materials for Oxygen Service
Haselmaier L., Powell B.
A 500 Bar Gaseous Oxygen Impact Test Apparatus for Burn-Out Testing of Oxygen Equipment
Binder C., Herrmann P., Kieper G.
Design of the LOX and GOX Systems for the Stennis Space Center High Heat Flux Facility
Yentzen M.
New Test Capabilities for the Evaluation of Material Flammability in Oxygen-Enriched Atmospheres
Scown B., Steinberg T.
Promoted Ignition-Combustion Behavior of Light Metals in Oxygen Enriched Atmospheres
McIlroy K., Million J., Zawierucha R.
Ignition and Combustion of Titanium and Titanium Alloys
Beeson H., Gunaji M., Sircar S.
Effect of Beryllium on the Burn Propensity of Titanium Alloys
Schmees R.
Promoted Combustion of Pure Metals in Oxygen-Enriched Atmospheres
Bryan C., Kazaroff J., Sircar S., Stoltzfus J.
Flammability of Metals in Fluorine and Nitrogen Trifluoride
Gugliemini C., Kadri S., Martrich R., Slusser J., Vora J., Werley B., Woytek A.
Reaction of Molten/Burning Aluminum with Liquid Oxygen
Barthélémy H., Muller C.
An Evaluation of Polymers as Ignition Sources During Particle Impact in Oxygen
Dees J., Forsyth E., Gunaji M., Stoltzfus J.
Cone Calorimeter Testing of Epoxy/Fiberglass and Broninated Epoxy/Fiberglass Composites in Normal Oxygen and Oxygen-Enriched Environments
Beeson H., Hshieh F.
The Effects of Configuration, Forced Convection, and Oxygen Concentration on the Flammability Behavior of Electronic Equipment
Altemir D., Janoff D., Pedley M., Rimanosky E.
Evaluation of the Compatibility of Materials Used in Breathing-Air Devices
Bryan C., Gunaji M., Jain A.
A Protocol for Evaluating the Cleaning Efficiency, Corrosion Property and Oxygen Compatibility of Non-Ozone Depleting Cleaning Agents
Chou T., Fiedorowicz A.
Laser-Assisted Cleaning of Contaminated Surfaces
Engelsberg A.
Medical Oxygen Administration: A Comparison of National Training Courses
Starr L.
Case Study of an Oxygen-Acetylene Cutting Torch Failure and Measured Overpressures Due to Flashback Reactions
Anderson D., Henry S., Hull W., Newton B., Porter A., Randall L.
Author Index
Subject Index
Committee: G04
Paper ID: STP1267-EB
DOI: 10.1520/STP1267-EB
ISBN-EB: 978-0-8031-5314-1
 ASTM International is a member of CrossRef.
0-8031-2004-4
978-0-8031-2004-4
STP1267-EB
|
