ASTM Standards Source (Online):
    Plastics and Plastic Piping


    TABLE OF CONTENTS

    (Standards will be added, revised or withdrawn on an ongoing basis.)

    C581 Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service

    C582 Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment

    C1147 Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics

    D256 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics

    D494 Standard Test Method for Acetone Extraction of Phenolic Molded or Laminated Products

    D542 Standard Test Method for Index of Refraction of Transparent Organic Plastics

    D543 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents

    D570 Standard Test Method for Water Absorption of Plastics

    D618 Standard Practice for Conditioning Plastics for Testing

    D635 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

    D638 Standard Test Method for Tensile Properties of Plastics

    D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position

    D695 Standard Test Method for Compressive Properties of Rigid Plastics

    D696 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer

    D704 Standard Specification for Melamine-Formaldehyde Molding Compounds

    D705 Standard Specification for Urea-Formaldehyde Molding Compounds

    D706 Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds

    D707 Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds

    D731 Standard Test Method for Molding Index of Thermosetting Molding Powder

    D732 Standard Test Method for Shear Strength of Plastics by Punch Tool

    D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact

    D747 Standard Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam

    D785 Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials

    D787 Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds

    D788 Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds

    D789 Standard Test Methods for Determination of Solution Viscosities of Polyamide (PA)

    D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

    D882 Standard Test Method for Tensile Properties of Thin Plastic Sheeting

    D883 Standard Terminology Relating to Plastics

    D952 Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials

    D953 Standard Test Method for Bearing Strength of Plastics

    D955 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics

    D957 Standard Practice for Determining Surface Temperature of Molds for Plastics

    D1003 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics

    D1004 Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting

    D1042 Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture

    D1043 Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test

    D1044 Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion

    D1045 Standard Test Methods for Sampling and Testing Plasticizers Used in Plastics

    D1056 Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber

    D1201 Standard Specification for Thermosetting Polyester Molding Compounds

    D1203 Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods

    D1204 Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature

    D1238 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer

    D1239 Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals

    D1243 Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers

    D1248 Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

    D1430 Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics

    D1435 Standard Practice for Outdoor Weathering of Plastics

    D1494 Standard Test Method for Diffuse Light Transmission Factor of Reinforced Plastics Panels

    D1499 Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics

    D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique

    D1525 Standard Test Method for Vicat Softening Temperature of Plastics

    D1562 Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds

    D1593 Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting

    D1598 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

    D1599 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings

    D1600 Standard Terminology for Abbreviated Terms Relating to Plastics

    D1601 Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers

    D1603 Standard Test Method for Carbon Black Content in Olefin Plastics

    D1621 Standard Test Method for Compressive Properties Of Rigid Cellular Plastics

    D1622/D1622M Standard Test Method for Apparent Density of Rigid Cellular Plastics

    D1623 Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics

    D1636 Standard Specification for Allyl Molding Compounds

    D1667 Standard Specification for Flexible Cellular Materials - Poly (Vinyl Chloride) Foam (Closed-Cell)

    D1693 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics

    D1708 Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens

    D1709 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method

    D1710 Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes

    D1712 Standard Practice for Resistance of Plastics to Sulfide Staining

    D1746 Standard Test Method for Transparency of Plastic Sheeting

    D1755 Standard Specification for Poly(Vinyl Chloride) Resins

    D1763 Standard Specification for Epoxy Resins

    D1784 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

    D1785 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120

    D1786 Standard Specification for Toluene Diisocyanate

    D1790 Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact

    D1822 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials

    D1823 Standard Test Method for Apparent Viscosity of Plastisols and Organosols at High Shear Rates by Extrusion Viscometer

    D1824 Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates

    D1894 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting

    D1895 Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials

    D1896/D1896M Standard Practice for Transfer Molding Test Specimens of Thermosetting Compounds

    D1921 Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials

    D1922 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method

    D1929 Standard Test Method for Determining Ignition Temperature of Plastics

    D1938 Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method

    D1998 Standard Specification for Polyethylene Upright Storage Tanks

    D2103 Standard Specification for Polyethylene Film and Sheeting

    D2105 Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube

    D2115 Standard Practice for Oven Heat Stability of Poly(Vinyl Chloride) Compositions

    D2116 Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials

    D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2124 Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique

    D2126 Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging

    D2143 Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe

    D2152 Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion

    D2222 Standard Test Method for Methanol Extract of Vinyl Chloride Resins

    D2235 Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

    D2238 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1

    D2239 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

    D2241 Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)

    D2287 Standard Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds

    D2290 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe

    D2291 Standard Practice for Fabrication of Ring Test Specimens for Glass-Resin Composites

    D2310 Standard Classification for Machine-Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

    D2321 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

    D2343 Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics

    D2383 Standard Practice for Testing Plasticizer Compatibility in Poly(Vinyl Chloride) (PVC) Compounds Under Humid Conditions

    D2396 Standard Test Methods for Powder-Mix Time of Poly(Vinyl Chloride) (PVC) Resins Using a Torque Rheometer

    D2412 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2444 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

    D2457 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics

    D2463 Standard Test Method for Drop Impact Resistance of Blow-Molded Thermoplastic Containers

    D2464 Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

    D2466 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40

    D2467 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

    D2513 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

    D2517 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings

    D2538 Standard Practice for Fusion of Poly(Vinyl Chloride) (PVC) Compounds Using a Torque Rheometer

    D2561 Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers

    D2562 Standard Practice for Classifying Visual Defects in Parts Molded from Reinforced Thermosetting Plastics

    D2563 Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic Laminate Parts

    D2564 Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems

    D2565 Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications

    D2578 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films

    D2581 Standard Specification for Polybutylene (PB) Plastics Molding and Extrusion Materials

    D2582 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting

    D2583 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor

    D2584 Standard Test Method for Ignition Loss of Cured Reinforced Resins

    D2609 Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

    D2647 Standard Specification for Crosslinkable Ethylene Plastics

    D2657 Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings

    D2659 Standard Test Method for Column Crush Properties of Blown Thermoplastic Containers

    D2661 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

    D2665 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

    D2672 Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement

    D2673 Standard Specification for Oriented Polypropylene Film

    D2680 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping

    D2683 Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing

    D2684 Standard Test Method for Permeability of Thermoplastic Containers to Packaged Reagents or Proprietary Products

    D2729 Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

    D2732 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting

    D2734 Standard Test Methods for Void Content of Reinforced Plastics

    D2737 Standard Specification for Polyethylene (PE) Plastic Tubing

    D2749 Standard Symbols for Dimensions of Plastic Pipe Fittings

    D2765 Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics

    D2774 Standard Practice for Underground Installation of Thermoplastic Pressure Piping

    D2837 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

    D2838 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting

    D2839 Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene

    D2842 Standard Test Method for Water Absorption of Rigid Cellular Plastics

    D2843 Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics

    D2846/D2846M Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems

    D2852 Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings

    D2855 Standard Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings

    D2857 Standard Practice for Dilute Solution Viscosity of Polymers

    D2863 Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)

    D2911 Standard Specification for Dimensions and Tolerances for Plastic Bottles

    D2923 Standard Test Method for Rigidity of Polyolefin Film and Sheeting

    D2924 Standard Test Method for External Pressure Resistance of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

    D2925 Standard Test Method for Beam Deflection of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe Under Full Bore Flow

    D2949 Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

    D2990 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics

    D2992 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings

    D2996 Standard Specification for Filament-Wound Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

    D2997 Standard Specification for Centrifugally Cast Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

    D3012 Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven

    D3013 Standard Specification for Epoxy Molding Compounds

    D3014 Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position

    D3016 Standard Practice for Use of Liquid Exclusion Chromatography Terms and Relationships

    D3030 Standard Test Method for Volatile Matter (Including Water) of Vinyl Chloride Resins

    D3034 Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

    D3035 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

    D3045 Standard Practice for Heat Aging of Plastics Without Load

    D3122 Standard Specification for Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings

    D3123 Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds

    D3124 Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry

    D3138 Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components

    D3139 Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

    D3159 Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials

    D3212 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

    D3222 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials

    D3261 Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

    D3262 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe

    D3275 Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials

    D3291 Standard Practice for Compatibility of Plasticizers in Poly(Vinyl Chloride) Plastics Under Compression

    D3294 Standard Specification for PTFE Resin Molded Sheet and Molded Basic Shapes

    D3295 Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing

    D3296 Standard Specification for FEP-Fluorocarbon Tube

    D3299 Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

    D3307 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials

    D3308 Standard Specification for PTFE Resin Skived Tape

    D3311 Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns

    D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials

    D3354 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method

    D3364 Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications

    D3367 Standard Test Method for Plasticizer Sorption of Poly(Vinyl Chloride) Resins Under Applied Centrifugal Force

    D3368 Standard Specification for FEP-Fluorocarbon Sheet and Film

    D3418 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry

    D3419 Standard Practice for In-Line Screw-Injection Molding Test Specimens From Thermosetting Compounds

    D3420 Standard Test Method for Pendulum Impact Resistance of Plastic Film

    D3453 Standard Specification for Flexible Cellular Materials—Urethane for Furniture and Automotive Cushioning, Bedding, and Similar Applications

    D3465 Standard Test Method for Purity of Monomeric Plasticizers by Gas Chromatography

    D3489 Standard Test Methods for Microcellular Urethane Materials

    D3517 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe

    D3567 Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings

    D3574 Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams

    D3575 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers

    D3576 Standard Test Method for Cell Size of Rigid Cellular Plastics

    D3591 Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds

    D3594 Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers

    D3595 Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and Film

    D3596 Standard Practice for Determination of Gels (Fisheyes) In General-Purpose Poly(Vinyl Chloride) (PVC) Resins

    D3641 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials

    D3647 Standard Practice for Classifying Reinforced Plastic Pultruded Shapes According to Composition

    D3675 Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source

    D3676 Standard Specification for Rubber Cellular Cushion Used for Carpet or Rug Underlay

    D3678 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions

    D3679 Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding

    D3681 Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition

    D3748 Standard Practice for Evaluating High-Density Rigid Cellular Plastics

    D3749 Standard Test Method for Residual Vinyl Chloride Monomer in Poly(Vinyl Chloride) Resins by Gas Chromatographic Headspace Technique

    D3753 Standard Specification for Glass-Fiber-Reinforced Polyester Manholes and Wetwells

    D3754 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe

    D3763 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors

    D3768 Standard Test Method for Microcellular Urethanes—Flexural Recovery

    D3769 Standard Test Method for Microcellular Urethanes--High Temperature Sag

    D3795 Standard Test Method for Thermal Flow, Cure, and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer

    D3801 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position

    D3826 Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test

    D3835 Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer

    D3839 Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe

    D3840 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications

    D3841 Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels

    D3846 Standard Test Method for In-Plane Shear Strength of Reinforced Plastics

    D3851 Standard Specification for Urethane Microcellular Shoe Soling Materials

    D3892 Standard Practice for Packaging/Packing of Plastics

    D3895 Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry

    D3914 Standard Test Method for In-Plane Shear Strength of Pultruded Glass-Reinforced Plastic Rod

    D3915 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Pressure Applications

    D3916 Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod

    D3917 Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes

    D3918 Standard Terminology Relating to Reinforced Plastic Pultruded Products

    D3935 Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material

    D3965 Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings

    D3981 Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications

    D3982 Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts

    D4000 Standard Classification System for Specifying Plastic Materials

    D4001 Standard Test Method for Determination of Weight-Average Molecular Weight of Polymers By Light Scattering

    D4020 Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials

    D4024 Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges

    D4065 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures

    D4066 Standard Classification System for Nylon Injection and Extrusion Materials (PA)

    D4067 Standard Classification System for and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods

    D4068 Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane

    D4092 Standard Terminology for Plastics: Dynamic Mechanical Properties

    D4093 Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials

    D4094 Standard Test Method for Acid Content of Ethylene-Acrylic Acid Copolymers

    D4097 Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

    D4101 Standard Specification for Polypropylene Injection and Extrusion Materials

    D4161 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals

    D4167 Standard Specification for Fiber-Reinforced Plastic Fans and Blowers

    D4203 Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials

    D4204 Standard Practice for Preparing Plastic Film Specimens for a Round-Robin Study

    D4216 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC) Building Products Compounds

    D4218 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique

    D4226 Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products

    D4272 Standard Test Method for Total Energy Impact of Plastic Films By Dart Drop

    D4273 Standard Test Method for Polyurethane Raw Materials: Determination of Primary Hydroxyl Content of Polyether Polyols

    D4274 Standard Test Methods for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols

    D4275 Standard Test Method for Determination of Butylated Hydroxy Toluene (BHT) in Polymers of Ethylene and Ethylene–Vinyl Acetate (EVA) Copolymers By Gas Chromatography

    D4321 Standard Test Method for Package Yield of Plastic Film

    D4329 Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics

    D4349 Classification System and Basis for Specification for Polyphenylene Ether (PPE) Materials

    D4350 Standard Test Method for Corrosivity Index of Plastics and Fillers

    D4364 Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight

    D4385 Standard Practice for Classifying Visual Defects in Thermosetting Reinforced Plastic Pultruded Products

    D4396 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications

    D4397 Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications

    D4398 Standard Test Method for Determining the Chemical Resistance of Fiberglass-Reinforced Thermosetting Resins by One-Side Panel Exposure

    D4440 Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology

    D4441 Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene

    D4443 Standard Test Method for Determining Residual Vinyl Chloride Monomer Content in PPB Range in Vinyl Chloride Homo- and Co-Polymers by Headspace Gas Chromatography

    D4459 Standard Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications

    D4473 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior

    D4475 Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method

    D4476/D4476M Standard Test Method for Flexural Properties of Fiber Reinforced Pultruded Plastic Rods

    D4477 Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit

    D4495 Standard Test Method for Impact Resistance of Poly(Vinyl Chloride) (PVC) Rigid Profiles by Means of a Falling Weight

    D4508 Standard Test Method for Chip Impact Strength of Plastics

    D4526 Standard Practice for Determination of Volatiles in Polymers by Static Headspace Gas Chromatography

    D4549 Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS)

    D4551 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane

    D4591 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry

    D4603 Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer

    D4634 Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)

    D4635 Standard Specification for Polyethylene Films Made from Low-Density Polyethylene for General Use and Packaging Applications

    D4659 Standard Test Methods for Polyurethane Raw Materials: Determination of Specific Gravity of Isocyanates

    D4660 Standard Test Methods for Polyurethane Raw Materials: Determination of the Isomer Content of Toluenediisocyanate

    D4661 Standard Test Methods for Polyurethane Raw Materials: Determination of Total Chlorine in Isocyanates

    D4662 Standard Test Methods for Polyurethane Raw Materials: Determination of Acid and Alkalinity Numbers of Polyols

    D4663 Standard Test Method for Polyurethane Raw Materials Determination of Hydrolyzable Chlorine of Isocyanates

    D4669 Standard Test Method for Polyurethane Raw Materials: Determination of Specific Gravity of Polyols

    D4670 Standard Test Method for Polyurethane Raw Materials: Determination of Suspended Matter In Polyols

    D4671 Standard Test Method for Polyurethane Raw Materials Determination of Unsaturation of Polyols

    D4672 Standard Test Method for Polyurethane Raw Materials: Determination of Water Content of Polyols

    D4673 Standard Classification System for Acrylonitrile-Butadiene-Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials

    D4674 Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments

    D4703 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

    D4726 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used for Assembled Windows and Doors

    D4745 Standard Classification System and Basis for Specification for Filled Polytetrafluoroethlyene (PTFE) Molding and Extrusion Materials Using ASTM Methods

    D4754 Standard Test Method for Two-Sided Liquid Extraction of Plastic Materials Using FDA Migration Cell

    D4756 Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit

    D4801 Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm [0.010 in.] and Greater

    D4802 Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet

    D4803 Standard Test Method for Predicting Heat Buildup in PVC Building Products

    D4804 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics

    D4812 Standard Test Method for Unnotched Cantilever Beam Impact Resistance of Plastics

    D4819 Standard Specification for Flexible Cellular Materials Made From Polyolefin Plastics

    D4875 Standard Test Methods of Polyurethane Raw Materials: Determination of the Polymerized Ethylene Oxide Content of Polyether Polyols

    D4877 Standard Test Method for Polyurethane Raw Materials: Determination of APHA Color in Isocyanates

    D4878 Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Polyols

    D4883 Standard Test Method for Density of Polyethylene by the Ultrasound Technique

    D4889 Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Crude or Modified Isocyanates

    D4890 Standard Test Methods for Polyurethane Raw Materials: Determination of Gardner and APHA Color of Polyols

    D4894 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials

    D4895 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion

    D4968 Standard Guide for Annual Review of Test Methods and Specifications for Plastics

    D4969 Standard Specification for Polytetrafluoroethylene–(PTFE) Coated Glass Fabric

    D4976 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials

    D4986 Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials

    D5017 Standard Test Method for Determination of Linear Low Density Polyethylene (LLDPE) Composition by Carbon-13 Nuclear Magnetic Resonance

    D5023 Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending)

    D5024 Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression

    D5025 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials

    D5026 Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension

    D5028 Standard Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis

    D5045 Standard Test Methods for Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials

    D5047 Standard Specification for Polyethylene Terephthalate Film and Sheeting

    D5048 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame

    D5071 Standard Practice for Exposure of Photodegradable Plastics in a Xenon Arc Apparatus

    D5083 Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens

    D5117 Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock

    D5132 Standard Test Method for Horizontal Burning Rate of Polymeric Materials Used in Occupant Compartments of Motor Vehicles

    D5138 Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP)

    D5155 Standard Test Methods for Polyurethane Raw Materials Determination of the Isocyanate Content of Aromatic Isocyanates

    D5203 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources

    D5204 Standard Classification System for Polyamide-Imide (PAI) Molding and Extrusion Materials

    D5205 Standard Classification System for Polyetherimide (PEI) Materials

    D5206 Standard Test Method for Windload Resistance of Rigid Plastic Siding

    D5207 Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials

    D5208 Standard Practice for Fluorescent Ultraviolet (UV) Exposure of Photodegradable Plastics

    D5210 Standard Test Method for Determining the Anaerobic Biodegradation of Plastic Materials in the Presence of Municipal Sewage Sludge

    D5224 Standard Practice for Compression Molding Test Specimens of Thermosetting Molding Compounds

    D5225 Standard Test Method for Measuring Solution Viscosity of Polymers with a Differential Viscometer

    D5226 Standard Practice for Dissolving Polymer Materials

    D5227 Standard Test Method for Measurement of Hexane Extractable Content of Polyolefins

    D5260 Standard Classification for Chemical Resistance of Poly(Vinyl Chloride) (PVC) Homopolymer and Copolymer Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

    D5272 Standard Practice for Outdoor Exposure Testing of Photodegradable Plastics

    D5279 Standard Test Method for Plastics: Dynamic Mechanical Properties: In Torsion

    D5296 Standard Test Method for Molecular Weight Averages and Molecular Weight Distribution of Polystyrene by High Performance Size-Exclusion Chromatography

    D5319 Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels

    D5336 Standard Specification for Polyphthalamide (PPA) Injection Molding Materials

    D5338 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials Under Controlled Composting Conditions, Incorporating Thermophilic Temperatures

    D5364 Standard Guide for Design, Fabrication, and Erection of Fiberglass Reinforced Plastic Chimney Liners with Coal-Fired Units

    D5365 Standard Test Method for Long-Term Ring-Bending Strain of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

    D5418 Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Dual Cantilever Beam)

    D5419 Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Threaded Plastic Closures

    D5420 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)

    D5421 Standard Specification for Contact Molded Fiberglass (Glass-Fiber-Reinforced Thermosetting Resin) Flanges

    D5422 Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer

    D5436 Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes

    D5477 Standard Practice for Identification of Polymer Layers or Inclusions by Fourier Transform Infrared Microspectroscopy (FT-IR)

    D5491 Standard Classification for Recycled Post-Consumer Polyethylene Film Sources for Molding and Extrusion Materials

    D5492 Standard Test Method for Determination of Xylene Solubles in Propylene Plastics

    D5507 Standard Test Method for Determination of Trace Organic Impurities in Monomer Grade Vinyl Chloride by Capillary Column/Multidimensional Gas Chromatography

    D5508 Standard Test Method for Determination of Residual Acrylonitrile Monomer in Styrene-Acrylonitrile Copolymer Resins and Nitrile-Butadiene Rubber by Headspace-Capillary Gas Chromatography (HS-CGC)

    D5511 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions

    D5523 Standard Test Method for Polyurethane Raw Materials Acidity by Argentometric Determination of Hydrolyzable Chlorine in Monomeric, Aromatic Isocyanates

    D5526 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions

    D5575 Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers

    D5576 Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR)

    D5577 Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics

    D5592 Standard Guide for Material Properties Needed in Engineering Design Using Plastics

    D5594 Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR)

    D5628 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)

    D5629 Standard Test Method for Polyurethane Raw Materials Determination of Acidity in Low-Acidity Aromatic Isocyanates and Polyurethane Prepolymers

    D5630 Standard Test Method for Ash Content in Plastics

    D5672 Standard Test Method for Testing Flexible Cellular Materials Measurement of Indentation Force Deflection Using a 25-mm (1-in.) Deflection Technique

    D5675 Standard Classification for Low Molecular Weight PTFE and FEP Micronized Powders

    D5677 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines

    D5685 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings

    D5740 Standard Guide for Writing Material Standards in the Classification D4000 Format

    D5813 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems

    D5814 Standard Practice for Determination of Contamination in Recycled Poly(Ethylene Terephthalate) (PET) Flakes and Chips Using a Plaque Test

    D5857 Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology

    D5870 Standard Practice for Calculating Property Retention Index of Plastics

    D5926 Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems

    D5927 Standard Classification System for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods

    D5930 Standard Test Method for Thermal Conductivity of Plastics by Means of a Transient Line-Source Technique

    D5946 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements

    D5947 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens

    D5948 Standard Specification for Molding Compounds, Thermosetting

    D5988 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in Soil

    D5989 Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA)

    D5991 Standard Practice for Separation and Identification of Poly(Vinyl Chloride) (PVC) Contamination in Poly(Ethylene Terephthalate) (PET) Flake

    D5998 Standard Specification for Molded Polyethylene Shipping and Storage Drums

    D6040 Standard Guide to Standard Test Methods for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape

    D6041 Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings

    D6042 Standard Test Method for Determination of Phenolic Antioxidants and Erucamide Slip Additives in Polypropylene Homopolymer Formulations Using Liquid Chromatography (LC)

    D6068 Standard Test Method for Determining J-R Curves of Plastic Materials

    D6070 Standard Test Methods for Physical Properties of Smooth-Wall, Coilable, Polyethylene (PE) Conduit (Duct) for Preassembled Wire and Cable

    D6098 Standard Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC)

    D6099 Standard Test Method for Polyurethane Raw Materials: Determination of Acidity in Moderate to High Acidity Aromatic Isocyanates

    D6100 Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM)

    D6108 Standard Test Method for Compressive Properties of Plastic Lumber and Shapes

    D6109 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products

    D6110 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics

    D6111 Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement

    D6112 Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes

    D6117 Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes

    D6150 Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility

    D6226 Standard Test Method for Open Cell Content of Rigid Cellular Plastics

    D6247 Standard Test Method for Determination of Elemental Content of Polyolefins by Wavelength Dispersive X-ray Fluorescence Spectrometry

    D6248 Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry

    D6261 Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)

    D6262 Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)

    D6263 Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC)

    D6265 Standard Practice for Separation of Contaminants in Polymers Using an Extruder Filter Test

    D6272 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending

    D6287 Standard Practice for Cutting Film and Sheeting Test Specimens

    D6288 Standard Practice for Separation and Washing of Recycled Plastics Prior to Testing

    D6289 Standard Test Method for Measuring Shrinkage from Mold Dimensions of Molded Thermosetting Plastics

    D6290 Standard Test Method for Color Determination of Plastic Pellets

    D6338 Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPVs) Based on ASTM Standard Test Methods

    D6339 Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)

    D6340 Standard Test Methods for Determining Aerobic Biodegradation of Radiolabeled Plastic Materials in an Aqueous or Compost Environment

    D6341 Standard Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between –30 and 140°F (–34.4 and 60°C)

    D6342 Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy

    D6358 Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ISO Methods

    D6360 Standard Practice for Enclosed Carbon-Arc Exposures of Plastics

    D6394 Standard Specification for Sulfone Plastics (SP)

    D6395 Standard Test Method for Flatwise Flexural Impact Resistance of Rigid Plastics

    D6400 Standard Specification for Labeling of Plastics Designed to be Aerobically Composted in Municipal or Industrial Facilities

    D6436 Standard Guide for Reporting Properties for Plastics and Thermoplastic Elastomers

    D6437 Standard Test Method for Polyurethane Raw Materials: alkalinity in Low-Alkalinity Polyols (Determination of CPR values of Polyols)

    D6456 Standard Specification for Finished Parts Made from Polyimide Resin

    D6457 Standard Specification for Extruded and Compression Molded Rod and Heavy-Walled Tubing Made from Polytetrafluoroethylene (PTFE)

    D6474 Standard Test Method for Determining Molecular Weight Distribution and Molecular Weight Averages of Polyolefins by High Temperature Gel Permeation Chromatography

    D6576 Standard Specification for Flexible Cellular Rubber Chemically Blown

    D6585 Standard Specification for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape

    D6645 Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry

    D6662 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards

    D6691 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum

    D6712 Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes

    D6713 Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF)

    D6777 Standard Test Method for Relative Rigidity of Poly(Vinyl Chloride)(PVC) Siding

    D6778 Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM)

    D6779 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)

    D6783 Standard Specification for Polymer Concrete Pipe

    D6835 Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE)

    D6864 Standard Specification for Color and Appearance Retention of Solid Colored Plastic Siding Products

    D6865 Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM&

    D6866 Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis

    D6867 Standard Specification for Perfluoroalkoxy (PFA)-Fluoropolymer Tubing

    D6868 Standard Specification for Labeling of End Items that Incorporate Plastics and Polymers as Coatings or Additives with Paper and Other Substrates Designed to be Aerobically Composted in Municipal or Industrial Facilities

    D6869 Standard Test Method for Coulometric and Volumetric Determination of Moisture in Plastics Using the Karl Fischer Reaction (the Reaction of Iodine with Water)

    D6953 Standard Test Method for Determination of Antioxidants and Erucamide Slip Additives in Polyethylene Using Liquid Chromatography (LC)

    D6954 Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation

    D6979 Standard Test Method for Polyurethane Raw Materials: Determination of Basicity in Polyols, Expressed as Percent Nitrogen

    D6980 Standard Test Method for Determination of Moisture in Plastics by Loss in Weight

    D6988 Standard Guide for Determination of Thickness of Plastic Film Test Specimens

    D7026 Standard Guide for Sampling and Reporting of Results for Determination of Biobased Content of Materials via Carbon Isotope Analysis

    D7027 Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine

    D7029 Standard Test Method for Determination of Reactivity of Unsaturated Polyesters and Vinyl Esters at 180.0F [82.2°C]

    D7082 Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe

    D7083 Standard Practice for Determination of Monomeric Plasticizers in Poly (Vinyl Chloride) (PVC) by Gas Chromatography

    D7107 Standard Test Method for Creep Measurement of Self-Lubricating Bushings

    D7132 Standard Test Method for Determination of Retained Blowing Agent in Extruded Polystyrene Foam

    D7133 Standard Test Method for Polyurethane Raw Materials: Instrumental Measurement of Tristimulus CIELAB Color and Yellowness Index of Liquids

    D7134 Standard Test Method for Molecular Mass Averages and Molecular Mass Distribution of Atactic Polystyrene by Matrix Assisted Laser Desorption/Ionization (MALDI)-Time of Flight (TOF) Mass Spectrometry (MS)

    D7191 Standard Test Method for Determination of Moisture in Plastics by Relative Humidity Sensor

    D7192 Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors

    D7193 Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape

    D7194 Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE)

    D7209 Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products

    D7210 Standard Practice for Extraction of Additives in Polyolefin Plastics

    D7211 Standard Specification for Parts Machined from Polychlorotrifluoroethylene (PCTFE) and Intended for General Use

    D7251 Standard Specification for Color and Appearance Retention of Variegated Color Plastic Siding Products

    D7252 Standard Test Method for Polyurethane Raw Materials: Determination of Monomer and Isomers in Isocyanates

    D7253 Standard Test Method for Polyurethane Raw Materials: Determination of Acidity as Acid Number for Polyether Polyols

    D7254 Standard Specification for Polypropylene (PP) Siding

    D7258 Standard Specification for Polymeric Piles

    D7292 Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI)

    D7293 Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI)

    D7309 Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry

    D7310 Standard Guide for Defect Detection and Rating of Plastic Films Using Optical Sensors

    D7399 Standard Test Method for Determination of the Amount of Polypropylene (PP) in Polypropylene/LDPE Mixtures Using Infrared Spectrophotometer (FTIR)

    D7436 Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology

    D7444 Standard Practice for Heat and Humidity Aging of Oxidatively Degradable Plastics

    D7445 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)

    D7471 Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials

    D7472 Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials

    D7473 Standard Test Method for Weight Attrition of Plastic Materials in the Marine Environment by Open System Aquarium Incubations

    D7474 Standard Practice for Determining Residual Stresses in Extruded or Molded Sulfone Plastic (SP) Parts by Immersion in Various Chemical Reagents

    D7475 Standard Test Method for Determining the Aerobic Degradation and Anaerobic Biodegradation of Plastic Materials under Accelerated Bioreactor Landfill Conditions

    D7486 Standard Test Method for Measurement of Fines and Dust Particles on Plastic Pellets by Wet Analysis

    D7487 Standard Practice for Polyurethane Raw Materials: Polyurethane Foam Cup Test

    D7567 Standard Test Method for Determining Gel Content in Crosslinked Ethylene Plastics Using Pressurized Liquid Extraction

    D7568 Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications

    D7611/D7611M Standard Practice for Coding Plastic Manufactured Articles for Resin Identification

    D7710 Standard Test Method for Determination of Volume and Density of Rigid and Irregularly Shaped Molded Cellular Materials

    D7711 Standard Guide for Description of Polymer Pellet Defects

    D7745 Standard Practice for Testing Pultruded Composites

    D7774 Standard Test Method for Flexural Fatigue Properties of Plastics

    D7791 Standard Test Method for Uniaxial Fatigue Properties of Plastics

    D7793 Standard Specification for Insulated Vinyl Siding

    D7823 Standard Test Method for Determination of Low Level, Regulated Phthalates in Poly (Vinyl Chloride) Plastics by Thermal Desorption—Gas Chromatography/Mass Chromatography

    D7856 Standard Specification for Color and Appearance Retention of Solid and Variegated Color Plastic Siding Products using CIELab Color Space

    F402 Standard Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

    F405 Standard Specification for Corrugated Polyethylene (PE) Pipe and Fittings

    F409 Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

    F412 Standard Terminology Relating to Plastic Piping Systems

    F437 Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

    F438 Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

    F439 Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

    F441/F441M Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

    F442/F442M Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR–PR)

    F449 Standard Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control

    F477 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

    F480 Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80

    F481 Standard Practice for Installation of Thermoplastic Pipe and Corrugated Pipe in Septic Tank Leach Fields

    F493 Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

    F512 Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation

    F585 Standard Guide for Insertion of Flexible Polyethylene Pipe Into Existing Sewers

    F610/F610M Standard Test Method for Evaluating the Quality of Molded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings by the Heat Reversion Technique

    F628 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core

    F645 Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

    F656 Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings

    F667 Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings

    F679 Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings

    F689 Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings

    F714 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter

    F725 Standard Practice for Drafting Impact Test Requirements In Thermoplastic Pipe And Fittings Standards

    F758 Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage

    F794 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter

    F810 Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields

    F876 Standard Specification for Crosslinked Polyethylene (PEX) Tubing

    F877 Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems

    F891 Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core

    F894 Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe

    F905 Standard Practice for Qualification of Polyethylene Saddle-Fused Joints

    F913 Standard Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe

    F948 Standard Test Method for Time-to-Failure of Plastic Piping Systems and Components Under Constant Internal Pressure With Flow

    F949 Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings

    F1025 Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe

    F1041 Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing

    F1055 Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing

    F1056 Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings

    F1057 Standard Practice for Estimating the Quality of Extruded Poly (Vinyl Chloride) (PVC) Pipe by the Heat Reversion Technique

    F1216 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube

    F1281 Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe

    F1282 Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

    F1290 Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings

    F1336 Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings

    F1365 Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals

    F1412 Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems

    F1417 Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air

    F1429 Standard Test Method for Assembly Force of Plastic Underground Conduit Joints That Use Flexible Elastomeric Seals Located in the Bell

    F1473 Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins

    F1483 Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe

    F1488 Standard Specification for Coextruded Composite Pipe

    F1498 Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings

    F1499 Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)

    F1504 Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation

    F1533 Standard Specification for Deformed Polyethylene (PE) Liner

    F1545 Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges

    F1563 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing

    F1588 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)

    F1606 Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner

    F1668 Standard Guide for Construction Procedures for Buried Plastic Pipe

    F1673 Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems

    F1674 Standard Test Method for Joint Restraint Products for Use with PVC Pipe

    F1675 Standard Practice for Life-Cycle Cost Analysis of Plastic Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits

    F1697 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit

    F1698 Standard Practice for Installation of Poly(Vinyl Chloride)(PVC) Profile Strip Liner and Cementitious Grout for Rehabilitation of Existing Man-Entry Sewers and Conduits

    F1732 Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer and Drain Pipe Containing Recycled PVC Material

    F1733 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing

    F1734 Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe

    F1735 Standard Specification for Poly (Vinyl Chloride)(PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits

    F1741 Standard Practice for Installation of Machine Spiral Wound Poly (Vinyl Chloride) (PVC) Liner Pipe for Rehabilitation of Existing Sewers and Conduits

    F1743 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)

    F1759 Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications

    F1760 Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content

    F1802 Standard Test Method for Performance Testing of Excess Flow Valves

    F1803 Standard Specification for Poly (Vinyl Chloride)(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter

    F1804 Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation

    F1807 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

    F1865 Standard Specification for Mechanical Cold Expansion Insert Fitting With Compression Sleeve for Cross-linked Polyethylene (PEX) Tubing

    F1866 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings

    F1867 Standard Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation

    F1871 Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation

    F1901 Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems

    F1924 Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

    F1947 Standard Practice for Installation of Folded Poly (Vinyl Chloride) (PVC) Pipe into Existing Sewers and Conduits

    F1948 Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing

    F1960 Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing

    F1961 Standard Specification for Metal Mechanical Cold Flare Compression Fittings with Disc Spring for Crosslinked Polyethylene (PEX) Tubing

    F1962 Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings

    F1970 Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems

    F1973 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems

    F1974 Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe

    F1986 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems

    F1987 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems

    F2018 Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens

    F2019 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)

    F2021 Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems

    F2023 Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water

    F2080 Standard Specification for Cold-Expansion Fittings With Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe

    F2098 Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings

    F2135 Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings

    F2136 Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe

    F2138 Standard Specification for Excess Flow Valves for Natural Gas Service

    F2145 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing

    F2159 Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

    F2160 Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD)

    F2164 Standard Practice for Field Leak Testing of Polyethylene (PE) and Crosslinked Polyethylene (PEX) Pressure Piping Systems Using Hydrostatic Pressure

    F2165 Standard Specification for Flexible Pre-Insulated Piping

    F2176 Standard Specification for Mechanical Couplings Used on Polyethylene Conduit, Duct and Innerduct

    F2206 Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE) Plastic Pipe, Fittings, Sheet Stock, Plate Stock, or Block Stock

    F2207 Standard Specification for Cured-in-Place Pipe Lining System for Rehabilitation of Metallic Gas Pipe

    F2231 Standard Test Method for Charpy Impact Test on Thin Specimens of Polyethylene Used in Pressurized Pipes

    F2261 Standard Test Method for Pressure Rating Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 and 80 Socket-Type

    F2262 Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Tubing OD Controlled SDR9

    F2263 Standard Test Method for Evaluating the Oxidative Resistance of Polyethylene (PE) Pipe to Chlorinated Water

    F2306/F2306M Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications

    F2331 Standard Test Method for Determining Chemical Compatibility of Substances in Contact with Thermoplastic Pipe and Fittings Materials

    F2389 Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems

    F2390 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content

    F2418 Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers

    F2433 Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness

    F2434 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing

    F2435 Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe

    F2487 Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines

    F2509 Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

    F2510/F2510M Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated High Density Polyethylene Drainage Pipes

    F2536 Standard Guide for Installing Plastic DWV Piping Suspended from On-Grade Slabs

    F2561 Standard Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One Piece Main and Lateral Cured-in-Place Liner

    F2562/F2562M Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage

    F2599 Standard Practice for The Sectional Repair of Damaged Pipe By Means of An Inverted Cured-In-Place Liner

    F2600 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing

    F2618 Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems

    F2619/F2619M Standard Specification for High-Density Polyethylene (PE) Line Pipe

    F2620 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings

    F2623 Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 Tubing

    F2634 Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method

    F2648/F2648M Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

    F2649 Standard Specification for Corrugated High Density Polyethylene (HDPE) Grease Interceptor Tanks

    F2657 Standard Test Method for Outdoor Weathering Exposure of Crosslinked Polyethylene (PEX) Tubing

    F2658 Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings

    F2686 Standard Specification for Glass Fiber Reinforced Thermoplastic Pipe

    F2718 Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines

    F2719 Standard Practice for Installation of Polyethylene (PE) and Encapsulated Cement Mortar Formed in Place Lining System (FIPLS) for the Rehabilitation of Water Pipelines

    F2720/F2720M Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe

    F2735 Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

    F2736 Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe

    F2737 Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units

    F2762 Standard Specification for 12 to 30 in. (300 to 750 mm) Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

    F2763 Standard Specification for 30 to 60 in. [750 to 1500 mm] Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

    F2764/F2764M Standard Specification for 30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

    F2767 Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution

    F2768 Standard Specification for Modified Stub ACME Thread Joint with Elastomeric Seal in Plastic Piping Components

    F2769 Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems

    F2785 Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings

    F2786 Standard Practice for Field Leak Testing of Polyethylene (PE) Pressure Piping Systems Using Gaseous Media Under Pressure (Pneumatic Leak Testing)

    F2787 Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers

    F2788/F2788M Standard Specification for Metric-sized Crosslinked Polyethylene (PEX) Pipe

    F2805 Standard Specification for Multilayer Thermoplastic And Flexible Steel Pipe And Connections

    F2806 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR)

    F2807 Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications

    F2817 Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair

    F2818 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing

    F2829 Standard Specification for Metric-Sized Crosslinked Polyethylene (PEX) Pipe Systems

    F2830 Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer

    F2831 Standard Practice for Internal Non Structural Epoxy Barrier Coating Material Used In Rehabilitation of Metallic Pressurized Piping Systems

    F2854 Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing

    F2855 Standard Specification for Chlorinated Poly(Vinyl Chloride)/Aluminum/Chlorinated Poly(Vinyl Chloride) (CPVC-AL-CPVC) Composite Pressure Tubing

    F2880 Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes 3/4 in. to 65 in.

    F2881 Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications

    F2896 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids

    F2897 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)

    F2905/F2905M Standard Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fittings and Joints For Oil and Gas Producing Applications

    F2922 Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers

    F2928 Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods

    F2929 Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig

    F2945 Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings

    F2946 Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes

    F2947/F2947M Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

    F2968/F2968M Standard Specification for Black Crosslinked Polyethylene (PEX) Pipe, Fittings and Joints For Gas Distribution Applications

    F2969 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) IPS Dimensioned Pressure Pipe

    F2984 Standard Specification for Segmental Panel System for the Grout-in-Place-Liner (GIPL) Rehabilitation Method of Existing Man-Entry Size Sewers, Culverts, and Conduits

    F2986 Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications

    F2987 Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Heap Leach Aeration Applications

    F2994 Standard Practice for Utilization of Mobile, Automated Cured-In-Place Pipe (CIPP) Impregnation Systems

    F3034 Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE)

    700 ASTM plastics standards. Available as one-time collection, collection with quarterly updates, or LAN version with quarterly updates.