ASTM Standards Source (Online):
    Geoenvironmental Collection


    TABLE OF CONTENTS

    (Standards will be added, revised or withdrawn on an ongoing basis.)

    A29/A29M Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought

    A31 Standard Specification for Steel Rivets and Bars for Rivets, Pressure Vessels

    A36/A36M Standard Specification for Carbon Structural Steel

    A90/A90M Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings

    A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

    A183 Standard Specification for Carbon Steel Track Bolts and Nuts

    A193/A193M Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications

    A194/A194M Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both

    A239 Standard Practice for Locating the Thinnest Spot in a Zinc (Galvanized) Coating on Iron or Steel Articles,

    A307 Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength

    A320/A320M Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service

    A325M Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric)

    A325 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products

    A380/A380M Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems

    A392 Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric

    A394 Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare

    A437/A437M Standard Specification for Stainless and Alloy-Steel Turbine-Type Bolting Specially Heat Treated for High-Temperature Service

    A449 Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

    A453/A453M Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels

    A489 Standard Specification for Carbon Steel Lifting Eyes

    A490 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    A490M Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)

    A491 Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric

    A493 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

    A502 Standard Specification for Rivets, Steel, Structural

    A510/A510M Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel, and Alloy Steel

    A540/A540M Standard Specification for Alloy-Steel Bolting for Special Applications

    A563 Standard Specification for Carbon and Alloy Steel Nuts

    A574M Standard Specification for Alloy Steel Socket-Head Cap Screws (Metric)

    A574 Standard Specification for Alloy Steel Socket-Head Cap Screws

    A623 Standard Specification for Tin Mill Products, General Requirements

    A673/A673M Standard Specification for Sampling Procedure for Impact Testing of Structural Steel

    A709/A709M Standard Specification for Structural Steel for Bridges

    A751 Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A824 Standard Specification for Metallic-Coated Steel Marcelled Tension Wire for Use With Chain Link Fence

    A923 Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels

    A962/A962M Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range

    A967/A967M Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts

    A1004/A1004M Standard Practice for Establishing Conformance to the Minimum Expected Corrosion Characteristics of Metallic, Painted-Metallic, and Nonmetallic-Coated Steel Sheet Intended for Use as Cold Formed Framing Members

    A1014/A1014M Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service

    A1058 Standard Test Methods for Mechanical Testing of Steel Products—Metric

    A1071/A1071M Standard Test Method for Evaluating Hygrothermal Corrosion Resistance of Permanent Magnet Alloys

    A1082/A1082M Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications

    B6 Standard Specification for Zinc

    B19 Standard Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks

    B36/B36M Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar

    B96/B96M Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels

    B103/B103M Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

    B117 Standard Practice for Operating Salt Spray (Fog) Apparatus

    B121/B121M Standard Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar

    B122/B122M Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar

    B130 Standard Specification for Commercial Bronze Strip for Bullet Jackets

    B134/B134M Standard Specification for Brass Wire

    B152/B152M Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar

    B201 Standard Practice for Testing Chromate Coatings on Zinc and Cadmium Surfaces

    B211 Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire

    B244 Standard Test Method for Measurement of Thickness of Anodic Coatings on Aluminum and of Other Nonconductive Coatings on Nonmagnetic Basis Metals with Eddy-Current Instruments

    B370 Standard Specification for Copper Sheet and Strip for Building Construction

    B449 Standard Specification for Chromates on Aluminum

    B456 Standard Specification for Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus Chromium

    B487 Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section

    B499 Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals

    B504 Standard Test Method for Measurement of Thickness of Metallic Coatings by the Coulometric Method

    B555 Standard Guide for Measurement of Electrodeposited Metallic Coating Thicknesses by Dropping Test

    B565 Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods

    B567 Standard Test Method for Measurement of Coating Thickness by the Beta Backscatter Method

    B568 Standard Test Method for Measurement of Coating Thickness by X-Ray Spectrometry

    B659 Standard Guide for Measuring Thickness of Metallic and Inorganic Coatings

    B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    B734 Standard Specification for Electrodeposited Copper for Engineering Uses

    B765 Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings

    B798 Standard Test Method for Porosity in Gold or Palladium Coatings on Metal Substrates by Gel-Bulk Electrography

    B799 Standard Test Method for Porosity in Gold and Palladium Coatings by Sulfurous Acid/Sulfur-Dioxide Vapor

    B808 Standard Test Method for Monitoring of Atmospheric Corrosion Chambers by Quartz Crystal Microbalances

    B809 Standard Test Method for Porosity in Metallic Coatings by Humid Sulfur Vapor (“Flowers-of-Sulfur”)

    B810 Standard Test Method for Calibration of Atmospheric Corrosion Test Chambers by Change in Mass of Copper Coupons

    B812 Standard Test Method for Resistance to Environmental Degradation of Electrical Pressure Connections Involving Aluminum and Intended for Residential Applications

    B825 Standard Test Method for Coulometric Reduction of Surface Films on Metallic Test Samples

    B826 Standard Test Method for Monitoring Atmospheric Corrosion Tests by Electrical Resistance Probes

    B827 Standard Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests

    B845 Standard Guide for Mixed Flowing Gas (MFG) Tests for Electrical Contacts

    B850 Standard Guide for Post-Coating Treatments of Steel for Reducing the Risk of Hydrogen Embrittlement

    B858 Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys

    B866 Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion

    B877 Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method

    B895 Standard Test Methods for Evaluating the Corrosion Resistance of Stainless Steel Powder Metallurgy (PM) Parts/Specimens by Immersion in a Sodium Chloride Solution

    B912 Standard Specification for Passivation of Stainless Steels Using Electropolishing

    B920 Standard Practice for Porosity in Gold and Palladium Alloy Coatings on Metal Substrates by Vapors of Sodium Hypochlorite Solution

    B961 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application

    C177 Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

    C227 Standard Test Method for Potential Alkali Reactivity of Cement-Aggregate Combinations (Mortar-Bar Method)

    C411 Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation

    C509 Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material

    C514 Standard Specification for Nails for the Application of Gypsum Board

    C518 Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

    C542 Standard Specification for Lock-Strip Gaskets

    C692 Standard Test Method for Evaluating the Influence of Thermal Insulations on External Stress Corrosion Cracking Tendency of Austenitic Stainless Steel

    C696 Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Uranium Dioxide Powders and Pellets

    C697 Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Plutonium Dioxide Powders and Pellets

    C698 Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Mixed Oxides ((U, Pu)O2)

    C739 Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation

    C758 Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Plutonium Metal

    C759 Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Plutonium Nitrate Solutions

    C761 Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Uranium Hexafluoride

    C791 Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Boron Carbide

    C799 Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Uranyl Nitrate Solutions

    C800 Standard Specification for Glass Fiber Blanket Insulation (Aircraft Type)

    C864 Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers

    C876 Standard Test Method for Corrosion Potentials of Uncoated Reinforcing Steel in Concrete

    C954 Standard Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness

    C968 Standard Test Methods for Analysis of Sintered Gadolinium Oxide-Uranium Dioxide Pellets

    C1001 Standard Test Method for Radiochemical Determination of Plutonium in Soil by Alpha Spectroscopy

    C1002 Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs

    C1022 Standard Test Methods for Chemical and Atomic Absorption Analysis of Uranium-Ore Concentrate

    C1046 Standard Practice for In-Situ Measurement of Heat Flux and Temperature on Building Envelope Components

    C1055 Standard Guide for Heated System Surface Conditions that Produce Contact Burn Injuries

    C1057 Standard Practice for Determination of Skin Contact Temperature from Heated Surfaces Using a Mathematical Model and Thermesthesiometer

    C1062 Standard Guide for Design, Fabrication, and Installation of Nuclear Fuel Dissolution Facilities

    C1071 Standard Specification for Fibrous Glass Duct Lining Insulation (Thermal and Sound Absorbing Material)

    C1108 Standard Test Method for Plutonium by Controlled-Potential Coulometry

    C1130 Standard Practice for Calibrating Thin Heat Flux Transducers

    C1144 Standard Test Method for Splitting Tensile Strength for Brittle Nuclear Waste Forms

    C1152/C1152M Standard Test Method for Acid-Soluble Chloride in Mortar and Concrete

    C1165 Standard Test Method for Determining Plutonium by Controlled-Potential Coulometry in H2SO4 at a Platinum Working Electrode

    C1166 Standard Test Method for Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories

    C1217 Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials

    C1218/C1218M Standard Test Method for Water-Soluble Chloride in Mortar and Concrete

    C1219 Standard Test Methods for Arsenic in Uranium Hexafluoride

    C1221 Standard Test Method for Nondestructive Analysis of Special Nuclear Materials in Homogeneous Solutions by Gamma-Ray Spectrometry

    C1284 Standard Practice for Electrodeposition of the Actinides for Alpha Spectrometry

    C1285 Standard Test Methods for Determining Chemical Durability of Nuclear, Hazardous, and Mixed Waste Glasses and Multiphase Glass Ceramics: The Product Consistency Test (PCT)

    C1287 Standard Test Method for Determination of Impurities in Nuclear Grade Uranium Compounds by Inductively Coupled Plasma Mass Spectrometry

    C1307 Standard Test Method for Plutonium Assay by Plutonium (III) Diode Array Spectrophotometry

    C1316 Standard Test Method for Nondestructive Assay of Nuclear Material in Scrap and Waste by Passive-Active Neutron Counting Using 252Cf Shuffler

    C1396/C1396M Standard Specification for Gypsum Board

    C1408 Standard Test Method for Carbon (Total) in Uranium Oxide Powders and Pellets By Direct Combustion-Infrared Detection Method

    C1431 Standard Guide for Corrosion Testing of Aluminum-Based Spent Nuclear Fuel in Support of Repository Disposal

    C1458 Standard Test Method for Nondestructive Assay of Plutonium, Tritium and 241Am by Calorimetric Assay

    C1463 Standard Practices for Dissolving Glass Containing Radioactive and Mixed Waste for Chemical and Radiochemical Analysis

    C1485 Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using an Electric Radiant Heat Energy Source

    C1513 Standard Specification for Steel Tapping Screws for Cold-Formed Steel Framing Connections

    C1524 Standard Test Method for Water-Extractable Chloride in Aggregate (Soxhlet Method)

    C1533 Standard Guide for General Design Considerations for Hot Cell Equipment

    C1554 Standard Guide for Materials Handling Equipment for Hot Cells

    C1562 Standard Guide for Evaluation of Materials Used in Extended Service of Interim Spent Nuclear Fuel Dry Storage Systems

    C1572 Standard Guide for Dry Lead Glass and Oil-Filled Lead Glass Radiation Shielding Window Components for Remotely Operated Facilities

    C1582/C1582M Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete

    C1615 Standard Guide for Mechanical Drive Systems for Remote Operation in Hot Cell Facilities

    C1617 Standard Practice for Quantitative Accelerated Laboratory Evaluation of Extraction Solutions Containing Ions Leached from Thermal Insulation on Aqueous Corrosion of Metals

    C1661 Standard Guide for Viewing Systems for Remotely Operated Facilities

    C1662 Standard Practice for Measurement of the Glass Dissolution Rate Using the Single-Pass Flow-Through Test Method

    C1663 Standard Test Method for Measuring Waste Glass or Glass Ceramic Durability by Vapor Hydration Test

    C1682 Standard Guide for Characterization of Spent Nuclear Fuel in Support of Geologic Repository Disposal

    C1703 Standard Practice for Sampling of Gaseous Uranium Hexafluoride

    C1720 Standard Test Method for Determining Liquidus Temperature of Immobilized Waste Glasses and Simulated Waste Glasses

    C1725 Standard Guide for Hot Cell Specialized Support Equipment and Tools

    C1726/C1726M Standard Guide for Use of Modeling for Passive Gamma Measurements

    C1751 Standard Guide for Sampling Radioactive Tank Waste

    C1761/C1761M Standard Specification for Lightweight Aggregate for Internal Curing of Concrete

    D56 Standard Test Method for Flash Point by Tag Closed Cup Tester

    D86 Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure

    D92 Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester

    D93 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester

    D123 Standard Terminology Relating to Textiles

    D130 Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test

    D149 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies

    D187 Standard Test Method for Burning Quality of Kerosine

    D229 Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation

    D240 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter

    D350 Standard Test Methods for Flexible Treated Sleeving Used for Electrical Insulation

    D378 Standard Test Methods for Rubber (Elastomeric) Conveyor Belting, Flat Type

    D396 Standard Specification for Fuel Oils

    D470 Standard Test Methods for Crosslinked Insulations and Jackets for Wire and Cable

    D610 Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces

    D635 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

    D653 Standard Terminology Relating to Soil, Rock, and Contained Fluids

    D664 Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration

    D665 Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water

    D714 Standard Test Method for Evaluating Degree of Blistering of Paints

    D849 Standard Test Method for Copper Strip Corrosion by Industrial Aromatic Hydrocarbons

    D870 Standard Practice for Testing Water Resistance of Coatings Using Water Immersion

    D876 Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation

    D975 Standard Specification for Diesel Fuel Oils

    D1000 Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications

    D1014 Standard Practice for Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates

    D1141 Standard Practice for the Preparation of Substitute Ocean Water

    D1193 Standard Specification for Reagent Water

    D1230 Standard Test Method for Flammability of Apparel Textiles

    D1275 Standard Test Method for Corrosive Sulfur in Electrical Insulating Oils

    D1280 Standard Guide for Total Immersion Corrosion Test for Soak Tank Metal Cleaners

    D1310 Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus

    D1322 Standard Test Method for Smoke Point of Kerosine and Aviation Turbine Fuel

    D1360 Standard Test Method for Fire Retardancy of Paints (Cabinet Method)

    D1384 Standard Test Method for Corrosion Test for Engine Coolants in Glassware

    D1405/D1405M Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels

    D1414 Standard Test Methods for Rubber O-Rings

    D1452 Standard Practice for Soil Exploration and Sampling by Auger Borings

    D1586 Standard Test Method for Standard Penetration Test (SPT) and Split-Barrel Sampling of Soils

    D1611 Standard Test Method for Corrosion Produced by Leather in Contact with Metal

    D1654 Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments

    D1655 Standard Specification for Aviation Turbine Fuels

    D1735 Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus

    D1743 Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases

    D1748 Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet

    D1838 Standard Test Method for Copper Strip Corrosion by Liquefied Petroleum (LP) Gases

    D1929 Standard Test Method for Determining Ignition Temperature of Plastics

    D1997 Standard Test Method for Laboratory Determination of the Fiber Content of Peat Samples by Dry Mass

    D2010/D2010M Standard Test Methods for Evaluation of Total Sulfation Activity in the Atmosphere by the Lead Dioxide Technique

    D2059/D2059M Standard Test Method for Resistance of Zippers to Salt Spray (Fog)

    D2068 Standard Test Method for Determining Filter Blocking Tendency

    D2216 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

    D2247 Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity

    D2251 Standard Test Method for Metal Corrosion by Halogenated Organic Solvents and Their Admixtures

    D2274 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)

    D2304 Standard Test Method for Thermal Endurance of Rigid Electrical Insulating Materials

    D2434 Standard Test Method for Permeability of Granular Soils (Constant Head)

    D2487 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)

    D2488 Standard Practice for Description and Identification of Soils (Visual-Manual Procedure)

    D2570 Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants

    D2584 Standard Test Method for Ignition Loss of Cured Reinforced Resins

    D2622 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry

    D2633 Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable

    D2649 Standard Test Method for Corrosion Characteristics of Solid Film Lubricants

    D2671 Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use

    D2688 Standard Test Method for Corrosivity of Water in the Absence of Heat Transfer (Weight Loss Method)

    D2758 Standard Test Method for Engine Coolants by Engine Dynamometer

    D2766 Standard Test Method for Specific Heat of Liquids and Solids

    D2803 Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal

    D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants

    D2843 Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics

    D2847 Standard Practice for Testing Engine Coolants in Car and Light Truck Service

    D2859 Standard Test Method for Ignition Characteristics of Finished Textile Floor Covering Materials

    D2863 Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)

    D2883 Standard Test Method for Reaction Threshold Temperature of Liquid and Solid Materials

    D2898 Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

    D2944 Standard Practice of Sampling Processed Peat Materials

    D2973 Standard Test Method for Total Nitrogen in Peat Materials

    D2974 Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils

    D2978 Standard Test Method for Volume of Processed Peat Materials

    D2980 Standard Test Method for Volume Weights, Water-Holding Capacity, and Air Capacity of Water-Saturated Peat Materials

    D3014 Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position

    D3032 Standard Test Methods for Hookup Wire Insulation

    D3065 Standard Test Methods for Flammability of Aerosol Products

    D3115 Standard Test Method for Explosive Reactivity of Lubricants with Aerospace Alloys Under High Shear

    D3143/D3143M Standard Test Method for Flash Point of Cutback Asphalt with Tag Open-Cup Apparatus

    D3144 Standard Specification for Crosslinked Poly(Vinylidene Fluoride) Heat-Shrinkable Tubing for Electrical Insulation

    D3149 Standard Specification for Crosslinked Polyolefin Heat-Shrinkable Tubing for Electrical Insulation

    D3150 Standard Specification for Crosslinked and Noncrosslinked Poly(Vinyl Chloride) Heat-Shrinkable Tubing for Electrical Insulation

    D3201/D3201M Standard Test Method for Hygroscopic Properties of Fire-Retardant Wood and Wood-Based Products

    D3278 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus

    D3310 Standard Test Method for Determining Corrosivity of Adhesive Materials

    D3316 Standard Test Method for Stability of Perchloroethylene with Copper

    D3338/D3338M Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels

    D3359 Standard Test Methods for Measuring Adhesion by Tape Test

    D3385 Standard Test Method for Infiltration Rate of Soils in Field Using Double-Ring Infiltrometer

    D3404 Standard Guide for Measuring Matric Potential in Vadose Zone Using Tensiometers

    D3426 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Using Impulse Waves

    D3451 Standard Guide for Testing Coating Powders and Powder Coatings

    D3466 Standard Test Method for Ignition Temperature of Granular Activated Carbon

    D3482 Standard Practice for Determining Electrolytic Corrosion of Copper by Adhesives

    D3523 Standard Test Method for Spontaneous Heating Values of Liquids and Solids (Differential Mackey Test)

    D3574 Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams

    D3603 Standard Test Method for Rust-Preventing Characteristics of Steam Turbine Oil in the Presence of Water (Horizontal Disk Method)

    D3638 Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials

    D3675 Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source

    D3679 Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding

    D3699 Standard Specification for Kerosine

    D3703 Standard Test Method for Hydroperoxide Number of Aviation Turbine Fuels, Gasoline and Diesel Fuels

    D3801 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position

    D3806 Standard Test Method of Small-Scale Evaluation of Fire-Retardant Paints (2-Foot Tunnel Method)

    D3828 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester

    D3874 Standard Test Method for Ignition of Materials by Hot Wire Sources

    D3934 Standard Test Method for Flash/No Flash Test-Equilibrium Method by a Closed-Cup Apparatus

    D3941 Standard Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus

    D3987 Standard Practice for Shake Extraction of Solid Waste with Water

    D4000 Standard Classification System for Specifying Plastic Materials

    D4043 Standard Guide for Selection of Aquifer Test Method in Determining Hydraulic Properties by Well Techniques

    D4044 Standard Test Method for (Field Procedure) for Instantaneous Change in Head (Slug) Tests for Determining Hydraulic Properties of Aquifers

    D4048 Standard Test Method for Detection of Copper Corrosion from Lubricating Grease

    D4050 Standard Test Method for (Field Procedure) for Withdrawal and Injection Well Tests for Determining Hydraulic Properties of Aquifer Systems

    D4104 Standard Test Method (Analytical Procedure) for Determining Transmissivity of Nonleaky Confined Aquifers by Overdamped Well Response to Instantaneous Change in Head (Slug Tests)

    D4105 Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Modified Theis Nonequilibrium Method

    D4106 Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Theis Nonequilibrium Method

    D4151 Standard Test Method for Flammability of Blankets

    D4175 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants

    D4206 Standard Test Method for Sustained Burning of Liquid Mixtures Using the Small Scale Open-Cup Apparatus

    D4220/D4220M Standard Practices for Preserving and Transporting Soil Samples

    D4221 Standard Test Method for Dispersive Characteristics of Clay Soil by Double Hydrometer

    D4294 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry

    D4310 Standard Test Method for Determination of Sludging and Corrosion Tendencies of Inhibited Mineral Oils

    D4340 Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions

    D4350 Standard Test Method for Corrosivity Index of Plastics and Fillers

    D4373 Standard Test Method for Rapid Determination of Carbonate Content of Soils

    D4380 Standard Test Method for Density of Bentonitic Slurries

    D4381/D4381M Standard Test Method for Sand Content by Volume of Bentonitic Slurries

    D4391 Standard Terminology Relating to The Burning Behavior of Textiles

    D4404 Standard Test Method for Determination of Pore Volume and Pore Volume Distribution of Soil and Rock by Mercury Intrusion Porosimetry

    D4412 Standard Test Methods for Sulfate-Reducing Bacteria in Water and Water-Formed Deposits

    D4427 Standard Classification of Peat Samples by Laboratory Testing

    D4447 Standard Guide for Disposal of Laboratory Chemicals and Samples

    D4448 Standard Guide for Sampling Ground-Water Monitoring Wells

    D4511 Standard Test Method for Hydraulic Conductivity of Essentially Saturated Peat

    D4529 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels

    D4531 Standard Test Methods for Bulk Density of Peat and Peat Products

    D4542 Standard Test Method for Pore Water Extraction and Determination of the Soluble Salt Content of Soils by Refractometer

    D4544 Standard Practice for Estimating Peat Deposit Thickness

    D4547 Standard Guide for Sampling Waste and Soils for Volatile Organic Compounds

    D4585/D4585M Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation

    D4627 Standard Test Method for Iron Chip Corrosion for Water–Miscible Metalworking Fluids

    D4630 Standard Test Method for Determining Transmissivity and Storage Coefficient of Low-Permeability Rocks by In Situ Measurements Using the Constant Head Injection Test

    D4631 Standard Test Method for Determining Transmissivity and Storativity of Low Permeability Rocks by In Situ Measurements Using Pressure Pulse Technique

    D4646 Standard Test Method for 24-h Batch-Type Measurement of Contaminant Sorption by Soils and Sediments

    D4647/D4647M Standard Test Methods for Identification and Classification of Dispersive Clay Soils by the Pinhole Test

    D4658 Standard Test Method for Sulfide Ion in Water

    D4687 Standard Guide for General Planning of Waste Sampling

    D4696 Standard Guide for Pore-Liquid Sampling from the Vadose Zone

    D4700 Standard Guide for Soil Sampling from the Vadose Zone

    D4723 Standard Classification Index of and Descriptions of Textile Flammability Test Methods

    D4737 Standard Test Method for Calculated Cetane Index by Four Variable Equation

    D4778 Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions

    D4793 Standard Test Method for Sequential Batch Extraction of Waste with Water

    D4804 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics

    D4809 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)

    D4843 Standard Test Method for Wetting and Drying Test of Solid Wastes

    D4844 Standard Guide for Air Monitoring at Waste Management Facilities for Worker Protection

    D4851 Standard Test Methods for Coated and Laminated Fabrics for Architectural Use

    D4868 Standard Test Method for Estimation of Net and Gross Heat of Combustion of Burner and Diesel Fuels

    D4874 Standard Test Method for Leaching Solid Material in a Column Apparatus

    D4972 Standard Test Method for pH of Soils

    D4976 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials

    D4978 Standard Test Methods for Screening of Reactive Sulfides in Waste

    D4979 Standard Test Method for Physical Description Screening Analysis in Waste

    D4981 Standard Test Method for Screening of Oxidizers in Waste

    D4982 Standard Test Methods for Flammability Potential Screening Analysis of Waste

    D4986 Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials

    D4992 Standard Practice for Evaluation of Rock to be Used for Erosion Control

    D5013 Standard Practices for Sampling Wastes from Pipes and Other Point Discharges

    D5025 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials

    D5048 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame

    D5057 Standard Test Method for Screening Apparent Specific Gravity and Bulk Density of Waste

    D5058 Standard Practices for Compatibility of Screening Analysis of Waste

    D5065 Standard Guide for Assessing the Condition of Aged Coatings on Steel Surfaces

    D5084 Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter

    D5088 Standard Practice for Decontamination of Field Equipment Used at Waste Sites

    D5092 Standard Practice for Design and Installation of Groundwater Monitoring Wells

    D5093 Standard Test Method for Field Measurement of Infiltration Rate Using Double-Ring Infiltrometer with Sealed-Inner Ring

    D5121 Standard Practice for Preparation of Rock Slabs for Durability Testing

    D5126/D5126M Standard Guide for Comparison of Field Methods for Determining Hydraulic Conductivity in Vadose Zone

    D5132 Standard Test Method for Horizontal Burning Rate of Polymeric Materials Used in Occupant Compartments of Motor Vehicles

    D5143 Standard Test Method for Analysis of Nitroaromatic and Nitramine Explosive in Soil by High Performance Liquid Chromatography

    D5157 Standard Guide for Statistical Evaluation of Indoor Air Quality Models

    D5198 Standard Practice for Nitric Acid Digestion of Solid Waste

    D5207 Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials

    D5231 Standard Test Method for Determination of the Composition of Unprocessed Municipal Solid Waste

    D5232 Standard Test Method for Determining the Stability and Miscibility of a Solid, Semi-Solid, or Liquid Waste Material

    D5233 Standard Test Method for Single Batch Extraction Method for Wastes

    D5238 Standard Test Method for Smoldering Combustion Potential of Cotton-Based Batting

    D5240/D5240M Standard Test Method for Evaluation of Durability of Rock for Erosion Control Using Sodium Sulfate or Magnesium Sulfate

    D5254/D5254M Standard Practice for Minimum Set of Data Elements to Identify a Groundwater Site

    D5268 Standard Specification for Topsoil Used for Landscaping Purposes

    D5269 Standard Test Method for Determining Transmissivity of Nonleaky Confined Aquifers by the Theis Recovery Method

    D5270 Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers

    D5283 Standard Practice for Generation of Environmental Data Related to Waste Management Activities: Quality Assurance and Quality Control Planning and Implementation

    D5284 Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid

    D5288 Standard Test Method for Determining the Tracking Index of Electrical Insulating Materials Using Various Electrode Materials (Excluding Platinum)

    D5298 Standard Test Method for Measurement of Soil Potential (Suction) Using Filter Paper

    D5299 Standard Guide for Decommissioning of Groundwater Wells, Vadose Zone Monitoring Devices, Boreholes, and Other Devices for Environmental Activities

    D5306 Standard Test Method for Linear Flame Propagation Rate of Lubricating Oils and Hydraulic Fluids

    D5312/D5312M Standard Test Method for Evaluation of Durability of Rock for Erosion Control Under Freezing and Thawing Conditions

    D5313/D5313M Standard Test Method for Evaluation of Durability of Rock for Erosion Control Under Wetting and Drying Conditions

    D5314 Standard Guide for Soil Gas Monitoring in the Vadose Zone

    D5358 Standard Practice for Sampling with a Dipper or Pond Sampler

    D5367 Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted

    D5369 Standard Practice for Extraction of Solid Waste Samples for Chemical Analysis Using Soxhlet Extraction

    D5408 Standard Guide for Set of Data Elements to Describe a Groundwater Site; Part One - Additional Identification Descriptors

    D5409/D5409M Standard Guide for Set of Data Elements to Describe a Groundwater Site; Part Two - Physical Descriptors

    D5410 Standard Guide for Set of Data Elements to Describe a Groundwater Site; Part Three - Usage Descriptors

    D5424 Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration

    D5425 Standard Guide for Development of Fire Hazard Assessment Standards of Electrotechnical Products

    D5434 Standard Guide for Field Logging of Subsurface Explorations of Soil and Rock

    D5435 Standard Test Method for Diagnostic Soil Test for Plant Growth and Food Chain Protection

    D5447 Standard Guide for Application of a Groundwater Flow Model to a Site-Specific Problem

    D5451 Standard Practice for Sampling Using a Trier Sampler

    D5453 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence

    D5466 Standard Test Method for Determination of Volatile Organic Chemicals in Atmospheres (Canister Sampling Methodology)

    D5468 Standard Test Method for Gross Calorific and Ash Value of Waste Materials

    D5473 Standard Test Method for (Analytical Procedure for) Analyzing the Effects of Partial Penetration of Control Well and Determining the Horizontal and Vertical Hydraulic Conductivity in a Nonleaky Confined Aquifer

    D5474 Standard Guide for Selection of Data Elements for Groundwater Investigations

    D5485 Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter

    D5490 Standard Guide for Comparing Groundwater Flow Model Simulations to Site-Specific Information

    D5495 Standard Practice for Sampling With a Composite Liquid Waste Sampler (COLIWASA)

    D5513 Standard Practice for Microwave Digestion of Industrial Furnace Feedstreams and Waste for Trace Element Analysis

    D5516 Standard Test Method for Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood Exposed to Elevated Temperatures

    D5519 Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials

    D5521/D5521M Standard Guide for Development of Groundwater Monitoring Wells in Granular Aquifers

    D5530 Standard Test Method for Total Moisture of Hazardous Waste Fuel by Karl Fischer Titrimetry

    D5534 Standard Test Method for Vapor-Phase Rust-Preventing Characteristics of Hydraulic Fluids

    D5537 Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration

    D5539 Standard Specification for Seed Starter Mix

    D5608 Standard Practices for Decontamination of Field Equipment Used at Low Level Radioactive Waste Sites

    D5609 Standard Guide for Defining Boundary Conditions in Groundwater Flow Modeling

    D5610 Standard Guide for Defining Initial Conditions in Groundwater Flow Modeling

    D5611 Standard Guide for Conducting a Sensitivity Analysis for a Groundwater Flow Model Application

    D5633 Standard Practice for Sampling with a Scoop

    D5658 Standard Practice for Sampling Unconsolidated Waste From Trucks

    D5659 Standard Test Method for Chlorophenoxy Acid Herbicides in Waste Using HPLC

    D5664 Standard Test Method for Evaluating the Effects of Fire-Retardant Treatments and Elevated Temperatures on Strength Properties of Fire-Retardant Treated Lumber

    D5679 Standard Practice for Sampling Consolidated Solids in Drums or Similar Containers

    D5680 Standard Practice for Sampling Unconsolidated Solids in Drums or Similar Containers

    D5715 Standard Test Method for Estimating the Degree of Humification of Peat and Other Organic Soils (Visual/Manual Method)

    D5716 Standard Test Method for Measuring the Rate of Well Discharge by Circular Orifice Weir

    D5718 Standard Guide for Documenting a Groundwater Flow Model Application

    D5719 Standard Guide for Simulation of Subsurface Airflow Using Groundwater Flow Modeling Codes

    D5737 Standard Guide for Methods for Measuring Well Discharge

    D5738 Standard Guide for Displaying the Results of Chemical Analyses of Groundwater for Major Ions and Trace Elements - Diagrams for Single Analyses

    D5743 Standard Practice for Sampling Single or Multilayered Liquids, With or Without Solids, in Drums or Similar Containers

    D5744 Standard Test Method for Laboratory Weathering of Solid Materials Using a Humidity Cell

    D5745 Standard Guide for Developing and Implementing Short-Term Measures or Early Actions for Site Remediation

    D5746 Standard Classification of Environmental Condition of Property Area Types for Defense Base Closure and Realignment Facilities

    D5753 Standard Guide for Planning and Conducting Borehole Geophysical Logging

    D5754 Standard Guide for Displaying the Results of Chemical Analyses of Groundwater for Major Ions and Trace Elements - Trilinear Diagrams for Two or More Analyses

    D5771 Standard Test Method for Cloud Point of Petroleum Products (Optical Detection Stepped Cooling Method)

    D5772 Standard Test Method for Cloud Point of Petroleum Products (Linear Cooling Rate Method)

    D5773 Standard Test Method for Cloud Point of Petroleum Products (Constant Cooling Rate Method)

    D5777 Standard Guide for Using the Seismic Refraction Method for Subsurface Investigation

    D5779/D5779M Standard Test Method for Field Determination of Apparent Specific Gravity of Rock and Manmade Materials for Erosion Control

    D5781/D5781M Standard Guide for Use of Dual-Wall Reverse-Circulation Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices

    D5782 Standard Guide for Use of Direct Air-Rotary Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices

    D5783 Standard Guide for Use of Direct Rotary Drilling with Water-Based Drilling Fluid for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices

    D5784/D5784M Standard Guide for Use of Hollow-Stem Augers for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices

    D5785 Standard Test Method for (Analytical Procedure) for Determining Transmissivity of Confined Nonleaky Aquifers by Underdamped Well Response to Instantaneous Change in Head (Slug Test)

    D5786 Standard Practice for (Field Procedure) for Constant Drawdown Tests in Flowing Wells for Determining Hydraulic Properties of Aquifer Systems

    D5787 Standard Practice for Monitoring Well Protection

    D5791 Standard Guide for Using Probability Sampling Methods in Studies of Indoor Air Quality in Buildings

    D5792 Standard Practice for Generation of Environmental Data Related to Waste Management Activities: Development of Data Quality Objectives

    D5829 Standard Guide for Preparing a Training Program for Environmental Analytical Laboratories

    D5830 Standard Test Method for Solvents Analysis in Hazardous Waste Using Gas Chromatography

    D5831 Standard Test Method for Screening Fuels in Soils

    D5839 Standard Test Method for Trace Element Analysis of Hazardous Waste Fuel by Energy-Dispersive X-Ray Fluorescence Spectrometry

    D5850 Standard Test Method for (Analytical Procedure) Determining Transmissivity, Storage Coefficient, and Anisotropy Ratio from a Network of Partially Penetrating Wells

    D5855 Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Confined Nonleaky or Leaky Aquifer by Constant Drawdown Method in Flowing Well

    D5856 Standard Test Method for Measurement of Hydraulic Conductivity of Porous Material Using a Rigid-Wall, Compaction-Mold Permeameter

    D5864 Standard Test Method for Determining Aerobic Aquatic Biodegradation of Lubricants or Their Components

    D5865 Standard Test Method for Gross Calorific Value of Coal and Coke

    D5872/D5872M Standard Guide for Use of Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices

    D5875/D5875M Standard Guide for Use of Cable-Tool Drilling and Sampling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices

    D5876 Standard Guide for Use of Direct Rotary Wireline Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices

    D5879 Standard Practice for Surface Site Characterization for On-Site Septic Systems

    D5880 Standard Guide for Subsurface Flow and Transport Modeling

    D5881 Standard Test Method for (Analytical Procedure) Determining Transmissivity of Confined Nonleaky Aquifers by Critically Damped Well Response to Instantaneous Change in Head (Slug)

    D5883 Standard Guide for Use of Rotary Kiln Produced Expanded Shale, Clay or Slate (ESCS) as a Mineral Amendment in Topsoil Used for Landscaping and Related Purposes

    D5894 Standard Practice for Cyclic Salt Fog/UV Exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet)

    D5903 Standard Guide for Planning and Preparing for a Groundwater Sampling Event

    D5911/D5911M Standard Practice for Minimum Set of Data Elements to Identify a Soil Sampling Site

    D5921 Standard Practice for Subsurface Site Characterization of Test Pits for On-Site Septic Systems

    D5922 Standard Guide for Analysis of Spatial Variation in Geostatistical Site Investigations

    D5923 Standard Guide for Selection of Kriging Methods in Geostatistical Site Investigations

    D5924 Standard Guide for Selection of Simulation Approaches in Geostatistical Site Investigations

    D5928 Standard Test Method for Screening of Waste for Radioactivity

    D5933 Standard Specification for 2 5/8-in. and 4-in. Diameter Metal Shear Plates for Use in Wood Constructions

    D5956 Standard Guide for Sampling Strategies for Heterogeneous Wastes

    D5968 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 121°C

    D5969 Standard Test Method for Corrosion-Preventive Properties of Lubricating Greases in Presence of Dilute Synthetic Sea Water Environments

    D5978 Standard Guide for Maintenance and Rehabilitation of Groundwater Monitoring Wells

    D5979 Standard Guide for Conceptualization and Characterization of Groundwater Systems

    D5980 Standard Guide for Selection and Documentation of Existing Wells for Use in Environmental Site Characterization and Monitoring

    D5981 Standard Guide for Calibrating a Groundwater Flow Model Application

    D5995 Standard Guide for Environmental Site Characterization in Cold Regions

    D6000 Standard Guide for Presentation of Water-Level Information from Groundwater Sites

    D6001 Standard Guide for Direct-Push Groundwater Sampling for Environmental Site Characterization

    D6006 Standard Guide for Assessing Biodegradability of Hydraulic Fluids

    D6008 Standard Practice for Conducting Environmental Baseline Surveys

    D6009 Standard Guide for Sampling Waste Piles

    D6010 Standard Practice for Closed Vessel Microwave Solvent Extraction of Organic Compounds from Solid Matrices

    D6025 Standard Guide for Developing and Evaluating Groundwater Modeling Codes

    D6028 Standard Test Method (Analytical Procedure) for Determining Hydraulic Properties of a Confined Aquifer Taking into Consideration Storage of Water in Leaky Confining Beds by Modified Hantush Method

    D6029 Standard Test Method (Analytical Procedure) for Determining Hydraulic Properties of a Confined Aquifer and a Leaky Confining Bed with Negligible Storage by the Hantush-Jacob Method

    D6030 Standard Guide for Selection of Methods for Assessing Groundwater or Aquifer Sensitivity and Vulnerability

    D6031/D6031M Standard Test Method for Logging In Situ Moisture Content and Density of Soil and Rock by the Nuclear Method in Horizontal, Slanted, and Vertical Access Tubes

    D6033 Standard Guide for Describing the Functionality of a Groundwater Modeling Code

    D6034 Standard Test Method (Analytical Procedure) for Determining the Efficiency of a Production Well in a Confined Aquifer from a Constant Rate Pumping Test

    D6036 Standard Guide for Displaying the Results of Chemical Analyses of Groundwater for Major Ions and Trace Elements - Use of Maps

    D6044 Standard Guide for Representative Sampling for Management of Waste and Contaminated Media

    D6050 Standard Test Method for Determination of Insoluble Solids in Organic Liquid Hazardous Waste

    D6051 Standard Guide for Composite Sampling and Field Subsampling for Environmental Waste Management Activities

    D6052 Standard Test Method for Preparation and Elemental Analysis of Liquid Hazardous Waste by Energy-Dispersive X-Ray Fluorescence

    D6063 Standard Guide for Sampling of Drums and Similar Containers by Field Personnel

    D6067 Standard Practice for Using the Electronic Piezocone Penetrometer Tests for Environmental Site Characterization

    D6079 Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR)

    D6089 Standard Guide for Documenting a Groundwater Sampling Event

    D6092 Standard Practice for Specifying Standard Sizes of Stone for Erosion Control

    D6106 Standard Guide for Establishing Nomenclature of Groundwater Aquifers

    D6113 Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables

    D6138 Standard Test Method for Determination of Corrosion-Preventive Properties of Lubricating Greases Under Dynamic Wet Conditions (Emcor Test)

    D6139 Standard Test Method for Determining the Aerobic Aquatic Biodegradation of Lubricants or Their Components Using the Gledhill Shake Flask

    D6167 Standard Guide for Conducting Borehole Geophysical Logging: Mechanical Caliper

    D6168 Standard Guide for Selection of Minimum Set of Data Elements Required to Identify Locations Chosen for Field Collection of Information to Describe Soil, Rock, and Their Contained Fluids

    D6169/D6169M Standard Guide for Selection of Soil and Rock Sampling Devices Used With Drill Rigs for Environmental Investigations

    D6170 Standard Guide for Selecting a Groundwater Modeling Code

    D6171 Standard Guide for Documenting a Groundwater Modeling Code

    D6187 Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Laser-Induced Fluorescence

    D6194 Standard Test Method for Glow-Wire Ignition of Materials

    D6196 Standard Practice for Selection of Sorbents, Sampling, and Thermal Desorption Analysis Procedures for Volatile Organic Compounds in Air

    D6208 Standard Test Method for Repassivation Potential of Aluminum and Its Alloys by Galvanostatic Measurement

    D6217 Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration

    D6232 Standard Guide for Selection of Sampling Equipment for Waste and Contaminated Media Data Collection Activities

    D6233 Standard Guide for Data Assessment for Environmental Waste Management Activities

    D6234 Standard Test Method for Shake Extraction of Mining Waste by the Synthetic Precipitation Leaching Procedure

    D6235 Standard Practice for Expedited Site Characterization of Vadose Zone and Groundwater Contamination at Hazardous Waste Contaminated Sites

    D6245 Standard Guide for Using Indoor Carbon Dioxide Concentrations to Evaluate Indoor Air Quality and Ventilation

    D6246 Standard Practice for Evaluating the Performance of Diffusive Samplers

    D6250 Standard Practice for Derivation of Decision Point and Confidence Limit for Statistical Testing of Mean Concentration in Waste Management Decisions

    D6274 Standard Guide for Conducting Borehole Geophysical Logging - Gamma

    D6285 Standard Guide for Locating Abandoned Wells

    D6286 Standard Guide for Selection of Drilling Methods for Environmental Site Characterization

    D6294/D6294M Standard Test Method for Corrosion Resistance of Ferrous Metal Fastener Assemblies Used in Roofing and Waterproofing

    D6305 Standard Practice for Calculating Bending Strength Design Adjustment Factors for Fire-Retardant-Treated Plywood Roof Sheathing

    D6306 Standard Guide for Placement and Use of Diffusion Controlled Passive Monitors for Gaseous Pollutants in Indoor Air

    D6311 Standard Guide for Generation of Environmental Data Related to Waste Management Activities: Selection and Optimization of Sampling Design

    D6312 Standard Guide for Developing Appropriate Statistical Approaches for Groundwater Detection Monitoring Programs

    D6323 Standard Guide for Laboratory Subsampling of Media Related to Waste Management Activities

    D6343 Test Methods for Thin Thermally Conductive Solid Materials for Electrical Insulation and Dielectric Applications

    D6345 Standard Guide for Selection of Methods for Active, Integrative Sampling of Volatile Organic Compounds in Air

    D6384 Standard Terminology Relating to Biodegradability and Ecotoxicity of Lubricants

    D6391 Standard Test Method for Field Measurement of Hydraulic Conductivity Using Borehole Infiltration

    D6413/D6413M Standard Test Method for Flame Resistance of Textiles (Vertical Test)

    D6418 Standard Practice for Using the Disposable En Core Sampler for Sampling and Storing Soil for Volatile Organic Analysis

    D6429 Standard Guide for Selecting Surface Geophysical Methods

    D6430 Standard Guide for Using the Gravity Method for Subsurface Investigation

    D6431 Standard Guide for Using the Direct Current Resistivity Method for Subsurface Investigation

    D6432 Standard Guide for Using the Surface Ground Penetrating Radar Method for Subsurface Investigation

    D6449 Standard Test Method for Flow of Fine Aggregate Concrete for Fabric Formed Concrete (Flow Cone Method)

    D6450 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester

    D6452 Standard Guide for Purging Methods for Wells Used for Groundwater Quality Investigations

    D6459 Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Performance in Protecting Hillslopes from Rainfall-Induced Erosion

    D6460 Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Performance in Protecting Earthen Channels from Stormwater-Induced Erosion

    D6461 Standard Specification for Silt Fence Materials

    D6462 Standard Practice for Silt Fence Installation

    D6469 Standard Guide for Microbial Contamination in Fuels and Fuel Systems

    D6473 Standard Test Method for Specific Gravity and Absorption of Rock For Erosion Control

    D6475 Standard Test Method for Measuring Mass Per Unit Area of Erosion Control Blankets

    D6513 Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests

    D6517 Standard Guide for Field Preservation of Groundwater Samples

    D6527 Standard Test Method for Determining Unsaturated and Saturated Hydraulic Conductivity in Porous Media by Steady-State Centrifugation

    D6538 Standard Guide for Sampling Wastewater With Automatic Samplers

    D6539 Standard Test Method for Measurement of the Permeability of Unsaturated Porous Materials by Flowing Air

    D6545 Standard Test Method for Flammability of Textiles Used in Children's Sleepwear

    D6557 Standard Test Method for Evaluation of Rust Preventive Characteristics of Automotive Engine Oils

    D6564 Standard Guide for Field Filtration of Groundwater Samples

    D6565 Standard Test Method for Determination of Water (Moisture) Content of Soil by the Time-Domain Reflectometry (TDR) Method

    D6572 Standard Test Methods for Determining Dispersive Characteristics of Clayey Soils by the Crumb Test

    D6584 Standard Test Method for Determination of Total Monoglycerides, Total Diglycerides, Total Triglycerides, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography

    D6594 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135°C

    D6597 Standard Practice for Assessment of Attaining Clean Up Level for Site Closure

    D6599 Standard Practice for Construction of Live Fascines on Slopes

    D6629 Standard Guide for Selection of Methods for Estimating Soil Loss by Erosion

    D6634/D6634M Standard Guide for the Selection of Purging and Sampling Devices for Groundwater Monitoring Wells

    D6639 Standard Guide for Using the Frequency Domain Electromagnetic Method for Subsurface Investigations

    D6640 Standard Practice for Collection and Handling of Soils Obtained in Core Barrel Samplers for Environmental Investigations

    D6642 Standard Guide for Comparison of Techniques to Quantify the Soil-Water (Moisture) Flux

    D6661 Standard Practice for Field Collection of Organic Compounds from Surfaces Using Wipe Sampling

    D6662 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards

    D6668 Standard Test Method for Discrimination Between Flammability Ratings of F = 0 and F = 1

    D6675 Standard Practice for Salt-Accelerated Outdoor Cosmetic Corrosion Testing of Organic Coatings on Automotive Sheet Steel

    D6684 Standard Specification for Materials and Manufacture of Articulating Concrete Block (ACB) Revetment Systems

    D6685 Standard Guide for the Selection of Test Methods for Fabrics Used for Fabric Formed Concrete (FFC)

    D6699 Standard Practice for Sampling Liquids Using Bailers

    D6711 Standard Practice for Specifying Rock to Fill Gabions, Revet Mattresses, and Gabion Mattresses

    D6724 Standard Guide for Installation of Direct Push Groundwater Monitoring Wells

    D6725 Standard Practice for Direct Push Installation of Prepacked Screen Monitoring Wells in Unconsolidated Aquifers

    D6726 Standard Guide for Conducting Borehole Geophysical Logging - Electromagnetic Induction

    D6727 Standard Guide for Conducting Borehole Geophysical Logging - Neutron

    D6751 Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels

    D6759 Standard Practice for Sampling Liquids Using Grab and Discrete Depth Samplers

    D6765 Standard Practice for Live Staking

    D6801 Standard Test Method for Measuring Maximum Spontaneous Heating Temperature of Art and Other Materials

    D6820 Standard Guide for Use of the Time Domain Electromagnetic Method for Subsurface Investigation

    D6825 Standard Guide for Placement of Riprap Revetments

    D6836 Standard Test Methods for Determination of the Soil Water Chararcteristic Curve for Desorption Using a Hanging Column, Pressure Extractor, Chilled Mirror Hygrometer, and/or Centrifuge

    D6841 Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-Retardant-Treated Lumber

    D6842 Standard Guide for Designing Cost-Effective Sampling and Measurement Plans by Use of Estimated Uncertainty and Its Components in Waste Management Decision-Making

    D6884 Standard Practice for Installation of Articulating Concrete Block (ACB) Revetment Systems

    D6890 Standard Test Method for Determination of Ignition Delay and Derived Cetane Number (DCN) of Diesel Fuel Oils by Combustion in a Constant Volume Chamber

    D6907 Standard Practice for Sampling Soils and Contaminated Media with Hand-Operated Bucket Augers

    D6910/D6910M Standard Test Method for Marsh Funnel Viscosity of Clay Construction Slurries

    D6911 Standard Guide for Packaging and Shipping Environmental Samples for Laboratory Analysis

    D6914 Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices

    D6956 Standard Guide for Demonstrating and Assessing Whether a Chemical Analytical Measurement System Provides Analytical Results Consistent with Their Intended Use

    D6982 Standard Practice for Detecting Hot Spots Using Point-Net (Grid) Search Patterns

    D7014 Standard Practice for Assembly and Placement of Double-Twisted Wire Mesh Gabions and Revet Mattresses

    D7016/D7016M Standard Test Method to Evaluate Edge Binding Components Used in Mattresses After Exposure to An Open Flame

    D7031 Standard Guide for Evaluating Mechanical and Physical Properties of Wood-Plastic Composite Products

    D7032 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)

    D7038 Standard Test Method for Evaluation of Moisture Corrosion Resistance of Automotive Gear Lubricants

    D7045 Standard Guide for Optimization of Groundwater Monitoring Constituents for Detection Monitoring Programs for RCRA Waste Disposal Facilities

    D7046 Standard Guide for Use of the Metal Detection Method for Subsurface Exploration

    D7047 Standard Test Method for Mucilloid Content of Plantago Insularis (Ovata, Psyllium)

    D7048 Standard Guide for Applying Statistical Methods for Assessment and Corrective Action Environmental Monitoring Programs

    D7069 Standard Guide for Field Quality Assurance in a Groundwater Sampling Event

    D7087 Standard Test Method for An Imaging Technique to Measure Rust Creepage at Scribe on Coated Test Panels Subjected to Corrosive Environments

    D7091 Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals

    D7094 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester

    D7095 Standard Test Method for Rapid Determination of Corrosiveness to Copper from Petroleum Products Using a Disposable Copper Foil Strip

    D7100 Standard Test Method for Hydraulic Conductivity Compatibility Testing of Soils with Aqueous Solutions

    D7101 Standard Index Test Method for Determination of Unvegetated Rolled Erosion Control Product (RECP) Ability to Protect Soil from Rain Splash and Associated Runoff Under Bench-Scale Conditions

    D7128 Standard Guide for Using the Seismic-Reflection Method for Shallow Subsurface Investigation

    D7140/D7140M Standard Test Method to Measure Heat Transfer Through Textile Thermal Barrier Materials

    D7170 Standard Test Method for Determination of Derived Cetane Number (DCN) of Diesel Fuel Oils—Fixed Range Injection Period, Constant Volume Combustion Chamber Method

    D7203 Standard Practice for Screening Trichloroethylene (TCE)-Contaminated Media Using a Heated Diode Sensor

    D7204 Standard Practice for Sampling Waste Streams on Conveyors

    D7208 Standard Test Method for Determination of Temporary Ditch Check Performance in Protecting Earthen Channels from Stormwater-Induced Erosion

    D7212 Standard Test Method for Low Sulfur in Automotive Fuels by Energy-Dispersive X-ray Fluorescence Spectrometry Using a Low-Background Proportional Counter

    D7220 Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry

    D7236 Standard Test Method for Flash Point by Small Scale Closed Cup Tester (Ramp Method)

    D7242/D7242M Standard Practice for Field Pneumatic Slug (Instantaneous Change in Head) Tests to Determine Hydraulic Properties of Aquifers with Direct Push Groundwater Samplers

    D7243 Standard Guide for Measuring the Saturated Hydraulic Conductivity of Paper Industry Sludges

    D7254 Standard Specification for Polypropylene (PP) Siding

    D7258 Standard Specification for Polymeric Piles

    D7262 Standard Test Method for Estimating the Permanganate Natural Oxidant Demand of Soil and Aquifer Solids

    D7276 Standard Guide for Analysis and Interpretation of Test Data for Articulating Concrete Block (ACB) Revetment Systems in Open Channel Flow

    D7277 Standard Test Method for Performance Testing of Articulating Concrete Block (ACB) Revetment Systems for Hydraulic Stability in Open Channel Flow

    D7294 Standard Guide for Collecting Treatment Process Design Data at a Contaminated Site—A Site Contaminated With Chemicals of Interest

    D7295 Standard Practice for Sampling and Determination of Hydrogen Cyanide (HCN) in Combustion Effluents and Other Stationary Sources

    D7297 Standard Practice for Evaluating Residential Indoor Air Quality Concerns

    D7309 Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry

    D7321 Standard Test Method for Test Method for Particulate Contamination of Biodiesel B100 Blend Stock Biodiesel Esters and Biodiesel Blends by Laboratory Filtration

    D7322 Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Ability to Encourage Seed Germination and Plant Growth Under Bench-Scale Conditions

    D7344 Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure (Mini Method)

    D7345 Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure (Micro Distillation Method

    D7346 Standard Test Method for No Flow Point and Pour Point of Petroleum Products

    D7351 Standard Test Method for Determination of Sediment Retention Device Effectiveness in Sheet Flow Applications

    D7352 Standard Practice for Direct Push Technology for Volatile Contaminant Logging with the Membrane Interface Probe (MIP)

    D7353 Standard Practice for Sampling of Liquids in Waste Management Activities Using a Peristaltic Pump

    D7367 Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic Planting

    D7371 Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method)

    D7374 Standard Practice for Evaluating Elevated Temperature Performance of Adhesives Used in End-Jointed Lumber

    D7376 Standard Practice for Outdoor Evaluation of Wet Stack Storage Conditions on Coil-Coated Metals

    D7397 Standard Test Method for Cloud Point of Petroleum Products (Miniaturized Optical Method)

    D7398 Standard Test Method for Boiling Range Distribution of Fatty Acid Methyl Esters (FAME) in the Boiling Range from 100 to 615°C by Gas Chromatography

    D7445 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)

    D7451 Standard Test Method for Water Separation Properties of Light and Middle Distillate, and Compression and Spark Ignition Fuels

    D7458 Standard Test Method for Determination of Beryllium in Soil, Rock, Sediment, and Fly Ash Using Ammonium Bifluoride Extraction and Fluorescence Detection

    D7462 Standard Test Method for Oxidation Stability of Biodiesel (B100) and Blends of Biodiesel with Middle Distillate Petroleum Fuel (Accelerated Method)

    D7463 Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures and Fuel Associated Water

    D7464 Standard Practice for Manual Sampling of Liquid Fuels, Associated Materials and Fuel System Components for Microbiological Testing

    D7467 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)

    D7470 Standard Practice for Evaluating Elevated Temperature Performance of End-Jointed Lumber Studs

    D7501 Standard Test Method for Determination of Fuel Filter Blocking Potential of Biodiesel (B100) Blend Stock by Cold Soak Filtration Test (CSFT)

    D7503 Standard Test Method for Measuring the Exchange Complex and Cation Exchange Capacity of Inorganic Fine-Grained Soils

    D7545 Standard Test Method for Oxidation Stability of Middle Distillate Fuels—Rapid Small Scale Oxidation Test (RSSOT)

    D7548 Standard Test Method for Determination of Accelerated Iron Corrosion in Petroleum Products

    D7571 Standard Specification for Retained Sewn Seam Strength After Exposures to Hot Air and Open Flame

    D7583 Standard Test Method for John Deere Coolant Cavitation Test

    D7591 Standard Test Method for Determination of Free and Total Glycerin in Biodiesel Blends by Anion Exchange Chromatography

    D7619 Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter

    D7620 Standard Test Method for Determination of Total Sulfur in Liquid Hydrocarbon Based Fuels by Continuous Injection, Air Oxidation and Ultraviolet Fluorescence Detection

    D7626 Standard Test Methods for Determining the Organic Treat Loading of Organophilic Clay

    D7648 Standard Practice for Active Soil Gas Sampling for Direct Push or Manual-Driven Hand-Sampling Equipment

    D7663 Standard Practice for Active Soil Gas Sampling in the Vadose Zone for Vapor Intrusion Evaluations

    D7664 Standard Test Methods for Measurement of Hydraulic Conductivity of Unsaturated Soils

    D7667 Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel—Thin Silver Strip Method

    D7668 Standard Test Method for Determination of Derived Cetane Number (DCN) of Diesel Fuel Oils—Ignition Delay and Combustion Delay Using a Constant Volume Combustion Chamber Method

    D7671 Standard Test Method for Corrosiveness to Silver by Automotive Spark–Ignition Engine Fuel–Silver Strip Method

    D7683 Standard Test Method for Cloud Point of Petroleum Products (Small Test Jar Method)

    D7687 Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel, Fuel/Water Mixtures, and Fuel-Associated Water with Sample Concentration by Filtration

    D7688 Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR) by Visual Observation

    D7699/D7699M Standard Practice for Minimum Geospatial Data for Abandoned Mine Land Problem Areas, Planning Units, Keyword Features, and Project Sites

    D7758 Standard Practice for Passive Soil Gas Sampling in the Vadose Zone for Source Identification, Spatial Variability Assessment, Monitoring, and Vapor Intrusion Evaluations

    D7760 Standard Test Method for Measurement of Hydraulic Conductivity of Tire Derived Aggregates Using a Rigid Wall Permeameter

    D7762 Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash

    D7765 Standard Practice for Use of Foundry Sand in Structural Fill and Embankments

    D7780 Standard Practice for Geospatial Data for Representing Coal Mining Features

    D7797 Test Method for Determination of the Fatty Acid Methyl Esters Content of Aviation Turbine Fuel Using Flow Analysis by Fourier Transform Infrared Spectroscopy – Rapid Screening Method

    D7831 Standard Practice for Sampling of Tanks by Field Personnel

    D7858 Standard Test Method for Determination of Bisphenol A in Soil, Sludge and Biosolids by Pressurized Fluid Extraction and Analyzed by Liquid Chromatography/Tandem Mass Spectrometry

    E3 Standard Guide for Preparation of Metallographic Specimens

    E8/E8M Standard Test Methods for Tension Testing of Metallic Materials

    E10 Standard Test Method for Brinell Hardness of Metallic Materials

    E18 Standard Test Methods for Rockwell Hardness of Metallic Materials

    E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E69 Standard Test Method for Combustible Properties of Treated Wood by the Fire-Tube Apparatus

    E74 Standard Practice of Calibration of Force-Measuring Instruments for Verifying the Force Indication of Testing Machines

    E84 Standard Test Method for Surface Burning Characteristics of Building Materials

    E108 Standard Test Methods for Fire Tests of Roof Coverings

    E110 Standard Test Method for Indentation Hardness of Metallic Materials by Portable Hardness Testers

    E112 Standard Test Methods for Determining Average Grain Size

    E119 Standard Test Methods for Fire Tests of Building Construction and Materials

    E122 Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process

    E136 Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C

    E140 Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness

    E144 Standard Practice for Safe Use of Oxygen Combustion Bombs

    E162 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source

    E176 Standard Terminology of Fire Standards

    E177 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods

    E205 Standard Specification for Glass and Oxygen Combustion Flask

    E285 Standard Test Method for Oxyacetylene Ablation Testing of Thermal Insulation Materials

    E340 Standard Test Method for Macroetching Metals and Alloys

    E376 Standard Practice for Measuring Coating Thickness by Magnetic-Field or Eddy-Current (Electromagnetic) Testing Methods

    E381 Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings

    E384 Standard Test Method for Knoop and Vickers Hardness of Materials

    E399 Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness KIc of Metallic Materials

    E424 Standard Test Methods for Solar Energy Transmittance and Reflectance (Terrestrial) of Sheet Materials

    E448 Standard Practice for Scleroscope Hardness Testing of Metallic Materials

    E456 Standard Terminology Relating to Quality and Statistics

    E459 Standard Test Method for Measuring Heat Transfer Rate Using a Thin-Skin Calorimeter

    E488/E488M Standard Test Methods for Strength of Anchors in Concrete Elements

    E502 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods

    E511 Standard Test Method for Measuring Heat Flux Using a Copper-Constantan Circular Foil, Heat-Flux Transducer

    E535 Standard Practice for Preparation of Fire-Test-Response Standards

    E566 Standard Practice for Electromagnetic (Eddy-Current) Sorting of Ferrous Metals

    E582 Standard Test Method for Minimum Ignition Energy and Quenching Distance in Gaseous Mixtures

    E598 Standard Test Method for Measuring Extreme Heat-Transfer Rates from High-Energy Environments Using a Transient, Null-Point Calorimeter

    E603 Standard Guide for Room Fire Experiments

    E605 Standard Test Methods for Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members

    E647 Standard Test Method for Measurement of Fatigue Crack Growth Rates

    E648 Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source

    E659 Standard Test Method for Autoignition Temperature of Liquid Chemicals

    E662 Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials

    E681 Standard Test Method for Concentration Limits of Flammability of Chemicals (Vapors and Gases)

    E683 Standard Practice for Installation and Service of Solar Space Heating Systems for One- and Two-Family Dwellings

    E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

    E698 Standard Test Method for Arrhenius Kinetic Constants for Thermally Unstable Materials Using Differential Scanning Calorimetry and the Flynn/Wall/Ozawa Method

    E709 Standard Guide for Magnetic Particle Testing

    E712 Standard Practice for Laboratory Screening of Metallic Containment Materials for Use With Liquids in Solar Heating and Cooling Systems

    E736 Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members

    E741 Standard Test Method for Determining Air Change in a Single Zone by Means of a Tracer Gas Dilution

    E744 Standard Practice for Evaluating Solar Absorptive Materials for Thermal Applications

    E745 Standard Practices for Simulated Service Testing for Corrosion of Metallic Containment Materials for Use With Heat-Transfer Fluids in Solar Heating and Cooling Systems

    E759 Standard Test Method for Effect of Deflection on Sprayed Fire-Resistive Material Applied to Structural Members

    E760 Standard Test Method for Effect of Impact on Bonding of Sprayed Fire-Resistive Material Applied to Structural Members

    E761 Standard Test Method for Compressive Strength of Sprayed Fire-Resistive Material Applied to Structural Members

    E772 Standard Terminology of Solar Energy Conversion

    E781 Standard Practice for Evaluating Absorptive Solar Receiver Materials When Exposed to Conditions Simulating Stagnation in Solar Collectors With Cover Plates

    E782 Standard Practice for Exposure of Cover Materials for Solar Collectors to Natural Weathering Under Conditions Simulating Operational Mode

    E800 Standard Guide for Measurement of Gases Present or Generated During Fires

    E814 Standard Test Method for Fire Tests of Penetration Firestop Systems

    E816 Standard Test Method for Calibration of Pyrheliometers by Comparison to Reference Pyrheliometers

    E822 Standard Practice for Determining Resistance of Solar Collector Covers to Hail by Impact With Propelled Ice Balls

    E824 Standard Test Method for Transfer of Calibration From Reference to Field Radiometers

    E859 Standard Test Method for Air Erosion of Sprayed Fire-Resistive Materials (SFRMs) Applied to Structural Members

    E861 Standard Practice for Evaluating Thermal Insulation Materials for Use in Solar Collectors

    E881 Standard Practice for Exposure of Solar Collector Cover Materials to Natural Weathering Under Conditions Simulating Stagnation Mode

    E882 Standard Guide for Accountability and Quality Control in the Chemical Analysis Laboratory

    E884 Standard Practice for Sampling Airborne Microorganisms at Municipal Solid-Waste Processing Facilities

    E903 Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres

    E905 Standard Test Method for Determining Thermal Performance of Tracking Concentrating Solar Collectors

    E906/E906M Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method

    E910 Standard Test Method for Application and Analysis of Helium Accumulation Fluence Monitors for Reactor Vessel Surveillance, E706 (IIIC)

    E918 Standard Practice for Determining Limits of Flammability of Chemicals at Elevated Temperature and Pressure

    E927 Standard Specification for Solar Simulation for Terrestrial Photovoltaic Testing

    E937 Standard Test Method for Corrosion of Steel by Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members

    E947 Standard Specification for Sampling Single-Phase Geothermal Liquid or Steam for Purposes of Chemical Analysis

    E948 Standard Test Method for Electrical Performance of Photovoltaic Cells Using Reference Cells Under Simulated Sunlight

    E957 Standard Terminology Relating to Geothermal Energy

    E970 Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

    E971 Standard Practice for Calculation of Photometric Transmittance and Reflectance of Materials to Solar Radiation

    E972 Standard Test Method for Solar Photometric Transmittance of Sheet Materials Using Sunlight

    E973 Standard Test Method for Determination of the Spectral Mismatch Parameter Between a Photovoltaic Device and a Photovoltaic Reference Cell

    E974 Standard Guide for Specifying Thermal Performance of Geothermal Power Systems

    E1008 Standard Practice for Installation, Inspection, and Maintenance of Valve-body Pressure-relief Methods for Geothermal and Other High-Temperature Liquid Applications

    E1021 Standard Test Method for Spectral Responsivity Measurements of Photovoltaic Devices

    E1036 Standard Test Methods for Electrical Performance of Nonconcentrator Terrestrial Photovoltaic Modules and Arrays Using Reference Cells

    E1038 Standard Test Method for Determining Resistance of Photovoltaic Modules to Hail by Impact with Propelled Ice Balls

    E1040 Standard Specification for Physical Characteristics of Nonconcentrator Terrestrial Photovoltaic Reference Cells

    E1056 Standard Practice for Installation and Service of Solar Domestic Water Heating Systems for One- and Two-Family Dwellings

    E1068 Standard Test Method for Testing Nonmetallic Seal Materials by Immersion in a Simulated Geothermal Test Fluid

    E1069 Standard Test Method for Testing Polymeric Seal Materials for Geothermal and/or High Temperature Service Under Sealing Stress

    E1084 Standard Test Method for Solar Transmittance (Terrestrial) of Sheet Materials Using Sunlight

    E1125 Standard Test Method for Calibration of Primary Non-Concentrator Terrestrial Photovoltaic Reference Cells Using a Tabular Spectrum

    E1143 Standard Test Method for Determining the Linearity of a Photovoltaic Device Parameter with Respect To a Test Parameter

    E1160 Standard Guide for On-Site Inspection and Verification of Operation of Solar Domestic Hot Water Systems

    E1171 Standard Test Methods for Photovoltaic Modules in Cyclic Temperature and Humidity Environments

    E1175 Standard Test Method for Determining Solar or Photopic Reflectance, Transmittance, and Absorptance of Materials Using a Large Diameter Integrating Sphere

    E1226 Standard Test Method for Explosibility of Dust Clouds

    E1232 Standard Test Method for Temperature Limit of Flammability of Chemicals

    E1317 Standard Test Method for Flammability of Marine Surface Finishes

    E1321 Standard Test Method for Determining Material Ignition and Flame Spread Properties

    E1352 Standard Test Method for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies

    E1353 Standard Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture

    E1354 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter

    E1355 Standard Guide for Evaluating the Predictive Capability of Deterministic Fire Models

    E1362 Standard Test Method for Calibration of Non-Concentrator Photovoltaic Secondary Reference Cells

    E1368 Standard Practice for Visual Inspection of Asbestos Abatement Projects

    E1386 Standard Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Solvent Extraction

    E1388 Standard Practice for Sampling of Headspace Vapors from Fire Debris Samples

    E1412 Standard Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Passive Headspace Concentration With Activated Charcoal

    E1413 Standard Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Dynamic Headspace Concentration

    E1445 Standard Terminology Relating to Hazard Potential of Chemicals

    E1461 Standard Test Method for Thermal Diffusivity by the Flash Method

    E1462 Standard Test Methods for Insulation Integrity and Ground Path Continuity of Photovoltaic Modules

    E1474 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter

    E1491 Standard Test Method for Minimum Autoignition Temperature of Dust Clouds

    E1513 Standard Practice for Application of Sprayed Fire-Resistive Materials (SFRMs)

    E1515 Standard Test Method for Minimum Explosible Concentration of Combustible Dusts

    E1527 Standard Practice for Environmental Site Assessments: Phase I Environmental Site Assessment Process

    E1528 Standard Practice for Limited Environmental Due Diligence: Transaction Screen Process

    E1529 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies

    E1537 Standard Test Method for Fire Testing of Upholstered Furniture

    E1546 Standard Guide for Development of Fire-Hazard-Assessment Standards

    E1590 Standard Test Method for Fire Testing of Mattresses

    E1591 Standard Guide for Obtaining Data for Fire Growth Models

    E1597 Standard Test Method for Saltwater Pressure Immersion and Temperature Testing of Photovoltaic Modules for Marine Environments

    E1618 Standard Test Method for Ignitable Liquid Residues in Extracts from Fire Debris Samples by Gas Chromatography-Mass Spectrometry

    E1623 Standard Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL)

    E1675 Standard Practice for Sampling Two-Phase Geothermal Fluid for Purposes of Chemical Analysis

    E1678 Standard Test Method for Measuring Smoke Toxicity for Use in Fire Hazard Analysis

    E1681 Standard Test Method for Determining Threshold Stress Intensity Factor for Environment-Assisted Cracking of Metallic Materials

    E1689 Standard Guide for Developing Conceptual Site Models for Contaminated Sites

    E1725 Standard Test Methods for Fire Tests of Fire-Resistive Barrier Systems for Electrical System Components

    E1732 Standard Terminology Relating to Forensic Science

    E1739 Standard Guide for Risk-Based Corrective Action Applied at Petroleum Release Sites

    E1740 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter

    E1776 Standard Guide for Development of Fire-Risk-Assessment Standards

    E1799 Standard Practice for Visual Inspections of Photovoltaic Modules

    E1802 Standard Test Methods for Wet Insulation Integrity Testing of Photovoltaic Modules

    E1822 Standard Test Method for Fire Testing of Stacked Chairs

    E1823 Standard Terminology Relating to Fatigue and Fracture Testing

    E1830 Standard Test Methods for Determining Mechanical Integrity of Photovoltaic Modules

    E1903 Standard Practice for Environmental Site Assessments: Phase II Environmental Site Assessment Process

    E1943 Standard Guide for Remediation of Ground Water by Natural Attenuation at Petroleum Release Sites

    E1966 Standard Test Method for Fire-Resistive Joint Systems

    E1981 Standard Guide for Assessing Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry

    E1990 Standard Guide for Performing Evaluations of Underground Storage Tank Systems for Operational Conformance with 40 CFR, Part 280 Regulations

    E1995 Standard Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber, With the Test Specimen Oriented Horizontally

    E2018 Standard Guide for Property Condition Assessments: Baseline Property Condition Assessment Process

    E2019 Standard Test Method for Minimum Ignition Energy of a Dust Cloud in Air

    E2021 Standard Test Method for Hot-Surface Ignition Temperature of Dust Layers

    E2031 Standard Practice for Quality Control of Psychophysiological Detection of Deception (Polygraph) Examinations

    E2047 Standard Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays

    E2058 Standard Test Methods for Measurement of Material Flammability Using a Fire Propagation Apparatus (FPA)

    E2060 Standard Guide for Use of Coal Combustion Products for Solidification/Stabilization of Inorganic Wastes

    E2061 Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles

    E2067 Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests

    E2079 Standard Test Methods for Limiting Oxygen (Oxidant) Concentration in Gases and Vapors

    E2081 Standard Guide for Risk-Based Corrective Action

    E2091 Standard Guide for Use of Activity and Use Limitations, Including Institutional and Engineering Controls

    E2102 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater

    E2107 Standard Practice for Environmental Regulatory Compliance Audits

    E2121 Standard Practice for Installing Radon Mitigation Systems in Existing Low-Rise Residential Buildings

    E2137 Standard Guide for Estimating Monetary Costs and Liabilities for Environmental Matters

    E2154 Standard Practice for Separation and Concentration of Ignitable Liquid Residues from Fire Debris Samples by Passive Headspace Concentration with Solid Phase Microextraction (SPME)

    E2173 Standard Guide for Disclosure of Environmental Liabilities

    E2174 Standard Practice for On-Site Inspection of Installed Fire Stops

    E2187 Standard Test Method for Measuring the Ignition Strength of Cigarettes

    E2201 Standard Terminology for Coal Combustion Products

    E2205/E2205M Standard Guide for Risk-Based Corrective Action for Protection of Ecological Resources

    E2226 Standard Practice for Application of Hose Stream

    E2230 Standard Practice for Thermal Qualification of Type B Packages for Radioactive Material

    E2231 Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics

    E2236 Standard Test Methods for Measurement of Electrical Performance and Spectral Response of Nonconcentrator Multijunction Photovoltaic Cells and Modules

    E2243 Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Re-contouring and Highwall Reclamation

    E2247 Standard Practice for Environmental Site Assessments: Phase I Environmental Site Assessment Process for Forestland or Rural Property

    E2256 Standard Guide for Hydraulic Integrity of New, Repaired, or Reconstructed Aboveground Storage Tank Bottoms for Petroleum Service

    E2257 Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies

    E2277 Standard Guide for Design and Construction of Coal Ash Structural Fills

    E2278 Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage

    E2280 Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities

    E2307 Standard Test Method for Determining Fire Resistance of Perimeter Fire Barrier Systems Using Intermediate-Scale, Multi-story Test Apparatus

    E2335 Standard Guide for Laboratory Monitors

    E2336 Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems

    E2348 Standard Guide for Framework for a Consensus-based Environmental Decision-making Process

    E2356 Standard Practice for Comprehensive Building Asbestos Surveys

    E2365 Standard Guide for Environmental Compliance Performance Assessment

    E2368 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing

    E2393 Standard Practice for On-Site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers

    E2404 Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (Including Vinyl) Wall or Ceiling Coverings, and of Facings and Wood Veneers Intended to be Applied on Site Over a Wood Substrate, to Assess Surface Burning Charact

    E2418 Standard Guide for Readily Observable Mold and Conditions Conducive to Mold in Commercial Buildings: Baseline Survey Process

    E2435 Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties

    E2451 Standard Practice for Preserving Ignitable Liquids and Ignitable Liquid Residue Extracts from Fire Debris Samples

    E2481 Standard Test Method for Hot Spot Protection Testing of Photovoltaic Modules

    E2527 Standard Test Method for Electrical Performance of Concentrator Terrestrial Photovoltaic Modules and Systems Under Natural Sunlight

    E2531 Standard Guide for Development of Conceptual Site Models and Remediation Strategies for Light Nonaqueous-Phase Liquids Released to the Subsurface

    E2536 Standard Guide for Assessment of Measurement Uncertainty in Fire Tests

    E2546 Standard Practice for Instrumented Indentation Testing

    E2558 Standard Test Method for Determining Particulate Matter Emissions from Fires in Wood-Burning Fireplaces

    E2573 Standard Practice for Specimen Preparation and Mounting of Site-Fabricated Stretch Systems to Assess Surface Burning Characteristics

    E2574/E2574M Standard Test Method for Fire Testing of School Bus Seat Assemblies

    E2579 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics

    E2599 Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics

    E2600 Standard Guide for Vapor Encroachment Screening on Property Involved in Real Estate Transactions

    E2616 Standard Guide for Remedy Selection Integrating Risk-Based Corrective Action and Non-Risk Considerations

    E2652 Standard Test Method for Behavior of Materials in a Tube Furnace with a Cone-shaped Airflow Stabilizer, at 750°C

    E2653 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Fire Test Method with Fewer Than Six Participating Laboratories

    E2681 Standard Guide for Environmental Management of Underground Storage Tank Systems Storing Hazardous Substances or Petroleum

    E2685 Standard Specification for Steel Blades Used with the Photovoltaic Module Surface Cut Test

    E2688 Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics

    E2690 Standard Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Characteristics

    E2707 Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure

    E2718 Standard Guide for Financial Disclosures Attributed to Climate Change

    E2725 Standard Guide for Basic Assessment and Management of Greenhouse Gases

    E2726/E2726M Standard Test Method for Evaluating the Fire-Test-Response of Deck Structures to Burning Brands

    E2733 Standard Guide for Investigation of Equipment Problems and Releases for Petroleum Underground Storage Tank Systems

    E2748 Standard Guide for Fire-Resistance Experiments

    E2749 Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens

    E2750 Standard Guide for Extension of Data from Penetration Firestop System Tests Conducted in Accordance with ASTM

    E2768 Standard Test Method for Extended Duration Surface Burning Characteristics of Building Materials (30 min Tunnel Test)

    E2790 Standard Guide for Identifying and Complying With Continuing Obligations

    E2797 Standard Practice for Building Energy Performance Assessment for a Building Involved in a Real Estate Transaction

    E2816 Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems

    E2837 Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies

    E2848 Standard Test Method for Reporting Photovoltaic Non-Concentrator System Performance

    E2856 Standard Guide for Estimation of LNAPL Transmissivity

    E2876 Standard Guide for Integrating Sustainable Objectives into Cleanup

    E2893 Standard Guide for Greener Cleanups

    E2908 Standard Guide for Fire Prevention for Photovoltaic Panels, Modules, and Systems

    F326 Standard Test Method for Electronic Measurement for Hydrogen Embrittlement From Cadmium-Electroplating Processes

    F400 Standard Consumer Safety Specification for Lighters

    F432 Standard Specification for Roof and Rock Bolts and Accessories

    F436 Standard Specification for Hardened Steel Washers

    F436M Standard Specification for Hardened Steel Washers [Metric]

    F467M Standard Specification for Nonferrous Nuts for General Use (Metric)

    F467 Standard Specification for Nonferrous Nuts for General Use

    F468M Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)

    F468 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use

    F482 Standard Practice for Corrosion of Aircraft Metals by Total Immersion in Maintenance Chemicals

    F483 Standard Practice for Total Immersion Corrosion Test for Aircraft Maintenance Chemicals

    F485 Standard Practice for Effects of Cleaners on Unpainted Aircraft Surfaces

    F495 Standard Test Method for Weight Loss of Gasket Materials Upon Exposure to Elevated Temperatures

    F519 Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments

    F537 Standard Specification for Design, Fabrication, and Installation of Fences Constructed of Wood and Related Materials

    F541 Standard Specification for Alloy Steel Eyebolts

    F547 Standard Terminology of Nails for Use with Wood and Wood-Base Materials

    F552 Standard Terminology Relating to Chain Link Fencing

    F567 Standard Practice for Installation of Chain-Link Fence

    F592 Standard Terminology of Collated and Cohered Fasteners and Their Application Tools

    F593 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs

    F594 Standard Specification for Stainless Steel Nuts

    F606 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F606M Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric)

    F626 Standard Specification for Fence Fittings

    F654 Standard Specification for Residential Chain Link Fence Gates

    F668 Standard Specification for Polyvinyl Chloride (PVC) and Other Organic Polymer-Coated Steel Chain-Link Fence Fabric

    F680 Standard Test Methods for Nails

    F746 Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials

    F788 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F793 Standard Classification of Wall Covering by Use Characteristics

    F812 Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series

    F835 Standard Specification for Alloy Steel Socket Button and Flat Countersunk Head Cap Screws

    F836M Standard Specification for Style 1 Stainless Steel Metric Nuts

    F837 Standard Specification for Stainless Steel Socket Head Cap Screws

    F844 Standard Specification for Washers, Steel, Plain (Flat), Unhardened for General Use

    F879 Standard Specification for Stainless Steel Socket Button and Flat Countersunk Head Cap Screws

    F880 Standard Specification for Stainless Steel Socket, Square Head, and Slotted Headless-Set Screws

    F897 Standard Test Method for Measuring Fretting Corrosion of Osteosynthesis Plates and Screws

    F900 Standard Specification for Industrial and Commercial Swing Gates

    F901 Standard Specification for Aluminum Transmission Tower Bolts and Nuts

    F912 Standard Specification for Alloy Steel Socket Set Screws

    F912M Standard Specification for Alloy Steel Socket Set Screws (Metric)

    F934 Standard Specification for Standard Colors for Polymer-Coated Chain Link Fence Materials

    F945 Standard Test Method for Stress-Corrosion of Titanium Alloys by Aircraft Engine Cleaning Materials

    F955 Standard Test Method for Evaluating Heat Transfer through Materials for Protective Clothing Upon Contact with Molten Substances

    F959M Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use With Structural Fasteners (Metric)

    F959 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners

    F963 Standard Consumer Safety Specification for Toy Safety

    F964 Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Exterior Profiles Used for Fencing and Railing

    F969 Standard Practice for Construction of Chain-Link Tennis Court Fence

    F1002 Standard Performance Specification for Protective Clothing and the Materials from Which It Is Made for Use by Workers Exposed to Specific Molten Substances and Related Thermal Hazards

    F1043 Standard Specification for Strength and Protective Coatings on Steel Industrial Fence Framework

    F1060 Standard Test Method for Thermal Protective Performance of Materials for Protective Clothing for Hot Surface Contact

    F1083 Standard Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded, for Fence Structures

    F1085 Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels

    F1089 Standard Test Method for Corrosion of Surgical Instruments

    F1110 Standard Test Method for Sandwich Corrosion Test

    F1111 Standard Test Method for Corrosion of Low-Embrittling Cadmium Plate by Aircraft Maintenance Chemicals

    F1113 Standard Test Method for Electrochemical Measurement of Diffusible Hydrogen in Steels (Barnacle Electrode)

    F1136/F1136M Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners

    F1137 Standard Specification for Phosphate/Oil Corrosion Protective Coatings for Fasteners

    F1141 Standard Specification for Wallcovering

    F1182 Standard Specification for Anodes, Sacrificial Zinc Alloy

    F1183 Standard Specification for Aluminum Alloy Chain Link Fence Fabric

    F1184 Standard Specification for Industrial and Commercial Horizontal Slide Gates

    F1291 Standard Test Method for Measuring the Thermal Insulation of Clothing Using a Heated Manikin

    F1345 Standard Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric

    F1358 Standard Test Method for Effects of Flame Impingement on Materials Used in Protective Clothing Not Designated Primarily for Flame Resistance

    F1379 Standard Terminology Relating to Barbed Tape

    F1387 Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings

    F1428 Standard Specification for Aluminum Particle-Filled Basecoat/Organic or Inorganic Topcoat, Corrosion Protective Coatings for Fasteners

    F1449 Standard Guide for Industrial Laundering of Flame, Thermal, and Arc Resistant Clothing

    F1459 Standard Test Method for Determination of the Susceptibility of Metallic Materials to Hydrogen Gas Embrittlement (HGE)

    F1469 Standard Guide for Conducting a Repeatability and Reproducibility Study on Test Equipment for Nondestructive Testing

    F1470 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1494 Standard Terminology Relating to Protective Clothing

    F1503 Standard Practice for Machine/Process Capability Study Procedure

    F1506 Standard Performance Specification for Flame Resistant and Arc Rated Textile Materials for Wearing Apparel for Use by Electrical Workers Exposed to Momentary Electric Arc and Related Thermal Hazards

    F1534 Standard Test Method for Determining Changes in Fire-Test-Response Characteristics of Cushioning Materials After Water Leaching

    F1550 Test Method for Determination of Fire-Test-Response Characteristics of Components or Composites of Mattresses or Furniture for Use in Correctional Facilities after Exposure to Vandalism, by Employing a Bench Scale Oxygen Consumption Calorimeter

    F1553 Standard Guide for Specifying Chain Link Fence

    F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength

    F1575 Standard Test Method for Determining Bending Yield Moment of Nails

    F1624 Standard Test Method for Measurement of Hydrogen Embrittlement Threshold in Steel by the Incremental Step Loading Technique

    F1664 Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Tension Wire Used with Chain-Link Fence

    F1665 Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Barbed Wire Used With Chain-Link Fence

    F1667 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples

    F1712 Standard Specification for Steel Chain-Link Fencing Materials Used for High Security Applications

    F1731 Standard Practice for Body Measurements and Sizing of Fire and Rescue Services Uniforms and Other Thermal Hazard Protective Clothing

    F1789 Standard Terminology for F16 Mechanical Fasteners

    F1801 Standard Practice for Corrosion Fatigue Testing of Metallic Implant Materials

    F1852 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    F1868 Standard Test Method for Thermal and Evaporative Resistance of Clothing Materials Using a Sweating Hot Plate

    F1870 Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities

    F1875 Standard Practice for Fretting Corrosion Testing of Modular Implant Interfaces: Hip Femoral Head-bore and Cone Taper Interface

    F1891 Standard Specification for Arc and Flame Resistant Rainwear

    F1908 Standard Guide for Fences for Residential Outdoor Swimming Pools, Hot Tubs, and Spas

    F1910 Standard Specification for Long Barbed Tape Obstacles

    F1911 Standard Practice for Installation of Barbed Tape

    F1915 Standard Test Methods for Glazing for Detention Facilities

    F1918 Standard Safety Performance Specification for Soft Contained Play Equipment

    F1930 Standard Test Method for Evaluation of Flame Resistant Clothing for Protection Against Fire Simulations Using an Instrumented Manikin

    F1939 Standard Test Method for Radiant Heat Resistance of Flame Resistant Clothing Materials with Continuous Heating

    F1940 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

    F1941M Standard Specification for Electrodeposited Coatings on Threaded Fasteners [Metric]

    F1941 Standard Specification for Electrodeposited Coatings on Threaded Fasteners (Unified Inch Screw Threads (UN/UNR))

    F1958/F1958M Standard Test Method for Determining the Ignitability of Non-flame-Resistant Materials for Clothing by Electric Arc Exposure Method Using Mannequins

    F1959/F1959M Standard Test Method for Determining the Arc Rating of Materials for Clothing

    F1972 Standard Guide for Terminology Relating to Candles and Associated Accessory Items

    F1999 Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Fence Systems

    F2000 Standard Guide for Fences for Baseball and Softball Fields

    F2049 Standard Safety Performance Specification for Fences/Barriers for Public, Commercial, and Multi-Family Residential Use Outdoor Play Areas

    F2058 Standard Specification for Candle Fire Safety Labeling

    F2078 Standard Terminology Relating to Hydrogen Embrittlement Testing

    F2111 Standard Practice for Measuring Intergranular Attack or End Grain Pitting on Metals Caused by Aircraft Chemical Processes

    F2129 Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements to Determine the Corrosion Susceptibility of Small Implant Devices

    F2178 Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products

    F2200 Standard Specification for Automated Vehicular Gate Construction

    F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    F2281 Standard Specification for Stainless Steel and Nickel Alloy Bolts, Hex Cap Screws, and Studs, for Heat Resistance and High Temperature Applications

    F2282 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners

    F2302 Standard Performance Specification for Labeling Protective Clothing as Heat and Flame Resistant

    F2328 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs

    F2328M Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs (Metric)

    F2329 Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners

    F2370 Standard Test Method for Measuring the Evaporative Resistance of Clothing Using a Sweating Manikin

    F2408 Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets

    F2409 Standard Guide for Fences for Non-Residential Outdoor Swimming Pools, Hot Tubs, and Spas

    F2417 Standard Specification for Fire Safety for Candles

    F2437 Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs

    F2453/F2453M Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) for Meshes of 6 in.2? [3871 mm2] or Less, in Panels or Rolls, with Uniform Meshes

    F2482 Standard Specification for Load-Indicating Externally Threaded Fasteners

    F2548 Standard Specification for Expanded Metal Fence Systems for Security Purposes

    F2589 Standard Specification for Ornamental Fences Employing Steel Tubular Pickets

    F2601 Standard Specification for Fire Safety for Candle Accessories

    F2611 Standard Guide for Design and Construction of Chain Link Security Fencing

    F2630 Standard Guide for Self-Closing/Self-Latching General-Purpose Gates

    F2631 Standard Practice for Installation of Chain-Link Fence for Outdoor Sports Fields, Sports Courts and Other Recreation Facilities

    F2676 Standard Test Method for Determining the Protective Performance of an Arc Protective Blanket for Electric Arc Hazards

    F2688 Standard Guide for System-Based, Customer-Centered Quality Plan for Manufacturers

    F2698 Standard Guide for Fences for Above-Ground and In-ground Skate Park Facilities

    F2699 Standard Guide for Fences for Commercial and Public Outdoor Water Spray/Play Areas

    F2700 Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame Resistant Materials for Clothing with Continuous Heating

    F2702 Standard Test Method for Radiant Heat Performance of Flame Resistant Clothing Materials with Burn Injury Prediction

    F2703 Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame Resistant Materials for Clothing with Burn Injury Prediction

    F2731 Standard Test Method for Measuring the Transmitted and Stored Energy of Firefighter Protective Clothing Systems

    F2733 Standard Specification for Flame Resistant Rainwear for Protection Against Flame Hazards

    F2780 Standard Guide for Design and Construction of Expanded Metal Security Fences and Barriers

    F2781 Standard Practice for Testing Forced Entry, Ballistic and Low Impact Resistance of Security Fence Systems

    F2814 Standard Guide for Design and Construction of Ornamental Steel Picket Fence Systems for Security Purposes

    F2832 Standard Guide for Accelerated Corrosion Testing for Mechanical Fasteners

    F2833 Standard Specification for Corrosion Protective Fastener Coatings with Zinc Rich Base Coat and Aluminum Organic/Inorganic Type

    F2866 Standard Test Method for Flammability of a Membrane Switch in Defined Assembly

    F2877/F2877M Standard Test Method for Shock Testing of Structural Insulation of A-Class Divisions Constructed of Steel or Aluminum

    F2894 Standard Test Method for Evaluation of Materials, Protective Clothing and Equipment for Heat Resistance Using a Hot Air Circulating Oven

    F2919/F2919M Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) with Variable Mesh Patterns or Meshes Greater than 6 in.2 [3871 mm2] in Panels

    F2957 Standard Specification for Ornamental Aluminum Fence Systems

    F3000/F3000M Standard Specification for Polymer Privacy Insert Slats for Chain Link Fabric and Privacy Chain Link Fabric Manufactured Containing Pre-Installed Privacy Slats

    G1 Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens

    G2/G2M Standard Test Method for Corrosion Testing of Products of Zirconium, Hafnium, and Their Alloys in Water at 680°F (360°C) or in Steam at 750°F (400°C)

    G3 Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing

    G4 Standard Guide for Conducting Corrosion Tests in Field Applications

    G5 Standard Reference Test Method for Making Potentiodynamic Anodic Polarization Measurements

    G16 Standard Guide for Applying Statistics to Analysis of Corrosion Data

    G28 Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys

    G30 Standard Practice for Making and Using U-Bend Stress-Corrosion Test Specimens

    G32 Standard Test Method for Cavitation Erosion Using Vibratory Apparatus

    G33 Standard Practice for Recording Data from Atmospheric Corrosion Tests of Metallic-Coated Steel Specimens

    G34 Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test)

    G35 Standard Practice for Determining the Susceptibility of Stainless Steels and Related Nickel-Chromium-Iron Alloys to Stress-Corrosion Cracking in Polythionic Acids

    G36 Standard Practice for Evaluating Stress-Corrosion-Cracking Resistance of Metals and Alloys in a Boiling Magnesium Chloride Solution

    G37 Standard Practice for Use of Mattsson's Solution of pH 7.2 to Evaluate the Stress- Corrosion Cracking Susceptibility of Copper-Zinc Alloys

    G38 Standard Practice for Making and Using C-Ring Stress-Corrosion Test Specimens

    G39 Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens

    G41 Standard Practice for Determining Cracking Susceptibility of Metals Exposed Under Stress to a Hot Salt Environment

    G44 Standard Practice for Exposure of Metals and Alloys by Alternate Immersion in Neutral 3.5?% Sodium Chloride Solution

    G46 Standard Guide for Examination and Evaluation of Pitting Corrosion

    G47 Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products

    G48 : Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution

    G49 Standard Practice for Preparation and Use of Direct Tension Stress-Corrosion Test Specimens

    G50 Standard Practice for Conducting Atmospheric Corrosion Tests on Metals

    G51 Standard Test Method for Measuring pH of Soil for Use in Corrosion Testing

    G52 Standard Practice for Exposing and Evaluating Metals and Alloys in Surface Seawater

    G57 Standard Test Method for Field Measurement of Soil Resistivity Using the Wenner Four-Electrode Method

    G58 Standard Practice for Preparation of Stress-Corrosion Test Specimens for Weldments

    G59 Standard Test Method for Conducting Potentiodynamic Polarization Resistance Measurements

    G60 Standard Practice for Conducting Cyclic Humidity Exposures

    G61 Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements for Localized Corrosion Susceptibility of Iron-, Nickel-, or Cobalt-Based Alloys

    G64 Standard Classification of Resistance to Stress-Corrosion Cracking of Heat-Treatable Aluminum Alloys

    G66 Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminum Alloys (ASSET Test)

    G67 Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)

    G69 Standard Test Method for Measurement of Corrosion Potentials of Aluminum Alloys

    G71 Standard Guide for Conducting and Evaluating Galvanic Corrosion Tests in Electrolytes

    G72/G72M Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment

    G73 Standard Test Method for Liquid Impingement Erosion Using Rotating Apparatus

    G74 Standard Test Method for Ignition Sensitivity of Nonmetallic Materials and Components by Gaseous Fluid Impact

    G78 Standard Guide for Crevice Corrosion Testing of Iron-Base and Nickel-Base Stainless Alloys in Seawater and Other Chloride-Containing Aqueous Environments

    G82 Standard Guide for Development and Use of a Galvanic Series for Predicting Galvanic Corrosion Performance

    G84 Standard Practice for Measurement of Time-of-Wetness on Surfaces Exposed to Wetting Conditions as in Atmospheric Corrosion Testing

    G85 Standard Practice for Modified Salt Spray (Fog) Testing

    G87 Standard Practice for Conducting Moist SO2 Tests

    G91 Standard Practice for Monitoring Atmospheric SO2 Deposition Rate for Atmospheric Corrosivity Evaluation

    G92 Standard Practice for Characterization of Atmospheric Test Sites

    G94 Standard Guide for Evaluating Metals for Oxygen Service

    G96 Standard Guide for Online Monitoring of Corrosion in Plant Equipment (Electrical and Electrochemical Methods)

    G97 Standard Test Method for Laboratory Evaluation of Magnesium Sacrificial Anode Test Specimens for Underground Applications

    G100 Standard Test Method for Conducting Cyclic Galvanostaircase Polarization

    G101 Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels

    G102 Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements

    G103 Standard Practice for Evaluating Stress-Corrosion Cracking Resistance of Low Copper 7XXX Series Al-Zn-Mg-Cu Alloys in Boiling 6% Sodium Chloride Solution

    G106 Standard Practice for Verification of Algorithm and Equipment for Electrochemical Impedance Measurements

    G107 Standard Guide for Formats for Collection and Compilation of Corrosion Data for Metals for Computerized Database Input

    G108 Standard Test Method for Electrochemical Reactivation (EPR) for Detecting Sensitization of AISI Type 304 and 304L Stainless Steels

    G109 Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments

    G110 Standard Practice for Evaluating Intergranular Corrosion Resistance of Heat Treatable Aluminum Alloys by Immersion in Sodium Chloride + Hydrogen Peroxide Solution

    G111 Standard Guide for Corrosion Tests in High Temperature or High Pressure Environment, or Both

    G112 Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys

    G114 Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service

    G116 Standard Practice for Conducting Wire-on-Bolt Test for Atmospheric Galvanic Corrosion

    G119 Standard Guide for Determining Synergism Between Wear and Corrosion

    G123 Standard Test Method for Evaluating Stress-Corrosion Cracking of Stainless Alloys with Different Nickel Content in Boiling Acidified Sodium Chloride Solution

    G124 Standard Test Method for Determining the Combustion Behavior of Metallic Materials in Oxygen-Enriched Atmospheres

    G125 Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants

    G129 Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking

    G130 Standard Test Method for Calibration of Narrow- and Broad-Band Ultraviolet Radiometers Using a Spectroradiometer

    G134 Standard Test Method for Erosion of Solid Materials by a Cavitating Liquid Jet

    G135 Standard Guide for Computerized Exchange of Corrosion Data for Metals

    G138 Standard Test Method for Calibration of a Spectroradiometer Using a Standard Source of Irradiance

    G139 Standard Test Method for Determining Stress-Corrosion Cracking Resistance of Heat-Treatable Aluminum Alloy Products Using Breaking Load Method

    G140 Standard Test Method for Determining Atmospheric Chloride Deposition Rate by Wet Candle Method

    G142 Standard Test Method for Determination of Susceptibility of Metals to Embrittlement in Hydrogen Containing Environments at High Pressure, High Temperature, or Both

    G145 Standard Guide for Studying Fire Incidents in Oxygen Systems

    G146 Standard Practice for Evaluation of Disbonding of Bimetallic Stainless Alloy/Steel Plate for Use in High-Pressure, High-Temperature Refinery Hydrogen Service

    G148 Standard Practice for Evaluation of Hydrogen Uptake, Permeation, and Transport in Metals by an Electrochemical Technique

    G150 Standard Test Method for Electrochemical Critical Pitting Temperature Testing of Stainless Steels

    G151 Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources

    G152 Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials

    G153 Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials

    G154 Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials

    G155 Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials

    G157 Standard Guide for Evaluating Corrosion Properties of Wrought Iron- and Nickel-Based Corrosion Resistant Alloys for Chemical Process Industries

    G158 Standard Guide for Three Methods of Assessing Buried Steel Tanks

    G161 Standard Guide for Corrosion-Related Failure Analysis

    G162 Standard Practice for Conducting and Evaluating Laboratory Corrosions Tests in Soils

    G165 Standard Practice for Determining Rail-to-Earth Resistance

    G167 Standard Test Method for Calibration of a Pyranometer Using a Pyrheliometer

    G168 Standard Practice for Making and Using Precracked Double Beam Stress Corrosion Specimens

    G170 Standard Guide for Evaluating and Qualifying Oilfield and Refinery Corrosion Inhibitors in the Laboratory

    G173 Standard Tables for Reference Solar Spectral Irradiances: Direct Normal and Hemispherical on 37° Tilted Surface

    G177 Standard Tables for Reference Solar Ultraviolet Spectral Distributions: Hemispherical on 37° Tilted Surface

    G180 Standard Test Method for Corrosion Inhibiting Admixtures for Steel in Concrete by Polarization Resistance in Cementitious Slurries

    G183 Standard Practice for Field Use of Pyranometers, Pyrheliometers and UV Radiometers

    G184 Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using Rotating Cage

    G185 Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using the Rotating Cylinder Electrode

    G186 Standard Test Method for Determining Whether Gas-Leak-Detector Fluid Solutions Can Cause Stress Corrosion Cracking of Brass Alloys

    G187 Standard Test Method for Measurement of Soil Resistivity Using the Two-Electrode Soil Box Method

    G188 Standard Specification for Leak Detector Solutions Intended for Use on Brasses and Other Copper Alloys

    G189 Standard Guide for Laboratory Simulation of Corrosion Under Insulation

    G192 Standard Test Method for Determining the Crevice Repassivation Potential of Corrosion-Resistant Alloys Using a Potentiodynamic-Galvanostatic-Potentiostatic Technique

    G197 Standard Table for Reference Solar Spectral Distributions: Direct and Diffuse on 20° Tilted and Vertical Surfaces

    G198 Standard Test Method for Determining the Relative Corrosion Performance of Driven Fasteners in Contact with Treated Wood

    G199 Standard Guide for Electrochemical Noise Measurement

    G200 Standard Test Method for Measurement of Oxidation-Reduction Potential (ORP) of Soil

    G202 Standard Test Method for Using Atmospheric Pressure Rotating Cage

    G205 Standard Guide for Determining Corrosivity of Crude Oils

    G207 Standard Test Method for Indoor Transfer of Calibration from Reference to Field Pyranometers

    200 ASTM standards used for environmental investigation and remediation. Available as a one-time collection, collection with quarterly updates, or LAN version with quarterly updates.