ASTM G40 - 13 Standard Terminology Relating to Wear and Erosion


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    B611 Standard Test Method for Determining the High Stress Abrasion Resistance of Hard Materials

    D2782 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Fluids (Timken Method)

    D3704 Standard Test Method for Wear Preventive Properties of Lubricating Greases Using the (Falex) Block on Ring Test Machine in Oscillating Motion

    D4857 Standard Test Method for Determination of the Ability of Lubricants to Minimize Ring Sticking and Piston Deposits in Two-Stroke-Cycle Gasoline Engines Other Than Outboards

    D5182 Standard Test Method for Evaluating the Scuffing Load Capacity of Oils (FZG Visual Method)

    D5706 Standard Test Method for Determining Extreme Pressure Properties of Lubricating Greases Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D5707 Standard Test Method for Measuring Friction and Wear Properties of Lubricating Grease Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D6425 Standard Test Method for Measuring Friction and Wear Properties of Extreme Pressure (EP) Lubricating Oils Using SRV Test Machine

    D6593 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions

    D6681 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure

    D6826 Standard Specification for Sprayed Slurries, Foams and Indigenous Materials Used As Alternative Daily Cover for Municipal Solid Waste Landfills

    D6923 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure

    D6984 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine

    D7217 Standard Test Method for Determining Extreme Pressure Properties of Solid Bonded Films Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7420 Standard Test Method for Determining Tribomechanical Properties of Grease Lubricated Plastic Socket Suspension Joints Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7421 Standard Test Method for Determining Extreme Pressure Properties of Lubricating Oils Using High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7594 Standard Test Method for Determining Fretting Wear Resistance of Lubricating Greases Under High Hertzian Contact Pressures Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7596 Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester

    D7684 Standard Guide for Microscopic Characterization of Particles from In-Service Lubricants

    D7690 Standard Practice for Microscopic Characterization of Particles from In-Service Lubricants by Analytical Ferrography

    D7898 Standard Practice for Lubrication and Hydraulic Filter Debris Analysis (FDA) for Condition Monitoring of Machinery

    E1605 Standard Terminology Relating to Lead in Buildings

    E2789 Standard Guide for Fretting Fatigue Testing

    F732 Standard Test Method for Wear Testing of Polymeric Materials Used in Total Joint Prostheses

    F1714 Standard Guide for Gravimetric Wear Assessment of Prosthetic Hip Designs in Simulator Devices

    F1875 Standard Practice for Fretting Corrosion Testing of Modular Implant Interfaces: Hip Femoral Head-bore and Cone Taper Interface

    G32 Standard Test Method for Cavitation Erosion Using Vibratory Apparatus

    G56 Standard Test Method for Abrasiveness of Ink-Impregnated Fabric Printer Ribbons and Other Web Materials

    G65 Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus

    G73 Standard Test Method for Liquid Impingement Erosion Using Rotating Apparatus

    G75 Standard Test Method for Determination of Slurry Abrasivity (Miller Number) and Slurry Abrasion Response of Materials (SAR Number)

    G76 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets

    G77 Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test

    G81 Standard Test Method for Jaw Crusher Gouging Abrasion Test

    G98 Standard Test Method for Galling Resistance of Materials

    G99 Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus

    G105 Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests

    G115 Standard Guide for Measuring and Reporting Friction Coefficients

    G118 Standard Guide for Recommended Format of Wear Test Data Suitable for Databases

    G119 Standard Guide for Determining Synergism Between Wear and Corrosion

    G132 Standard Test Method for Pin Abrasion Testing

    G133 Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear

    G134 Standard Test Method for Erosion of Solid Materials by a Cavitating Liquid Jet

    G137 Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration

    G143 Standard Test Method for Measurement of Web/Roller Friction Characteristics

    G163 Standard Guide for Digital Data Acquisition in Wear and Friction Measurements

    G171 Standard Test Method for Scratch Hardness of Materials Using a Diamond Stylus

    G174 Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact

    G176 Standard Test Method for Ranking Resistance of Plastics to Sliding Wear using Block-on-Ring Wear Test—Cumulative Wear Method

    G181 Standard Test Method for Conducting Friction Tests of Piston Ring and Cylinder Liner Materials Under Lubricated Conditions

    G182 Standard Test Method for Determination of the Breakaway Friction Characteristics of Rolling Element Bearings

    G190 Standard Guide for Developing and Selecting Wear Tests

    G194 Standard Test Method for Measuring Rolling Friction Characteristics of a Spherical Shape on a Flat Horizontal Plane

    G195 Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser

    G196 Standard Test Method for Galling Resistance of Material Couples

    G203 Standard Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems

    G204 Standard Test Method for Damage to Contacting Solid Surfaces under Fretting Conditions

    G206 Standard Guide for Measuring the Wear Volumes of Piston Ring Segments Run against Flat Coupons in Reciprocating Wear Tests


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    C242 Terminology of Ceramic Whitewares and Related Products