ASTM International - Standard References

A320/A320M Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service

A325 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

A394 Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare

A449 Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

A490 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

B839 Standard Test Method for Residual Embrittlement in Metallic Coated, Externally Threaded Articles, Fasteners, and Rod—Inclined Wedge Method

D3982 Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts

F432 Standard Specification for Roof and Rock Bolts and Accessories

F436M Standard Specification for Hardened Steel Washers [Metric]

F606 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

F844 Standard Specification for Washers, Steel, Plain (Flat), Unhardened for General Use

F959 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners

F1077 Standard Guide for Selection of Committee F16 Fastener Specifications

F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength

F1852 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength

F2437 Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs

		ASTM F436 - 11 Standard Specification for Hardened Steel Washers Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here. A320/A320M Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service A325 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners A394 Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare A449 Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use A490 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength B839 Standard Test Method for Residual Embrittlement in Metallic Coated, Externally Threaded Articles, Fasteners, and Rod—Inclined Wedge Method D3982 Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts F432 Standard Specification for Roof and Rock Bolts and Accessories F436M Standard Specification for Hardened Steel Washers [Metric] F606 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets F844 Standard Specification for Washers, Steel, Plain (Flat), Unhardened for General Use F959 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners F1077 Standard Guide for Selection of Committee F16 Fastener Specifications F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength F1852 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength F2437 Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM F436 - 11 Standard Specification for Hardened Steel Washers