ASTM F1789 - 14 Standard Terminology for F16 Mechanical Fasteners


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

    A307 Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60000 PSI Tensile Strength

    A325M Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric)

    A325 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A394 Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare

    A449 Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

    A489 Standard Specification for Carbon Steel Lifting Eyes

    A490 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    A490M Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)

    A563 Standard Specification for Carbon and Alloy Steel Nuts

    A563M Standard Specification for Carbon and Alloy Steel Nuts (Metric)

    A574 Standard Specification for Alloy Steel Socket-Head Cap Screws

    A574M Standard Specification for Alloy Steel Socket-Head Cap Screws (Metric)

    A1059/A1059M Standard Specification for Zinc Alloy Thermo-Diffusion Coatings (TDC) on Steel Fasteners, Hardware, and Other Products

    F436 Standard Specification for Hardened Steel Washers

    F436M Standard Specification for Hardened Steel Washers [Metric]

    F788 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F812 Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series

    F1136/F1136M Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners

    F1470 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1852 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    F2282 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners

    F2328 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts

    F2328M Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)

    F2329 Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners

    F2482 Standard Specification for Load-Indicating Externally Threaded Fasteners

    F2660 Standard Test Method for Qualifying Coatings for Use on A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement

    F2688 Standard Guide for System-Based, Customer-Centered Quality Plan for Manufacturers

    F2832 Standard Guide for Accelerated Corrosion Testing for Mechanical Fasteners

    F2833 Standard Specification for Corrosion Protective Fastener Coatings with Zinc Rich Base Coat and Aluminum Organic/Inorganic Type


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    A563 Specification for Carbon and Alloy Steel Nuts

    E456 Terminology Relating to Quality and Statistics

    F432 Specification for Roof and Rock Bolts and Accessories

    F2328 Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts

    F2482 Specification for Load-Indicating Externally Threaded Fasteners