ASTM E644 - 11 Standard Test Methods for Testing Industrial Resistance Thermometers


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    D113 Standard Test Method for Ductility of Bituminous Materials

    D402/D402M Standard Test Method for Distillation of Cutback Asphalt

    D2162 Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards

    D2726/D2726M Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures

    D2872 Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test)

    D3012 Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven

    D3143/D3143M Standard Test Method for Flash Point of Cutback Asphalt with Tag Open-Cup Apparatus

    D3829 Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil

    D4402/D4402M Standard Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer

    D4684 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature

    D5110 Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry

    D5801 Standard Test Method for Toughness and Tenacity of Bituminous Materials

    D5982 Standard Test Method for Determining Cement Content of Fresh Soil-Cement (Heat of Neutralization Method)

    D6084/D6084M Standard Test Method for Elastic Recovery of Bituminous Materials by Ductilometer

    D6176 Standard Practice for Measuring Surface Atmospheric Temperature with Electrical Resistance Temperature Sensors

    D6821 Standard Test Method for Low Temperature Viscosity of Drive Line Lubricants in a Constant Shear Stress Viscometer

    D6896 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature

    D7175 Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer

    D7552 Standard Test Method for Determining the Complex Shear Modulus (G*) Of Bituminous Mixtures Using Dynamic Shear Rheometer

    E220 Standard Test Method for Calibration of Thermocouples By Comparison Techniques

    E228 Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer

    E344 Terminology Relating to Thermometry and Hydrometry

    E1137/E1137M Standard Specification for Industrial Platinum Resistance Thermometers

    E1502 Standard Guide for Use of Fixed-Point Cells for Reference Temperatures

    E2488 Standard Guide for the Preparation and Evaluation of Liquid Baths Used for Temperature Calibration by Comparison

    E2593 Standard Guide for Accuracy Verification of Industrial Platinum Resistance Thermometers

    E2877 Standard Guide for Digital Contact Thermometers

    G151 Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    E1 Specification for ASTM Liquid-in-Glass Thermometers

    E77 Test Method for Inspection and Verification of Thermometers

    E230 Specification and Temperature-Electromotive Force (EMF) Tables for Standardized Thermocouples

    E344 Terminology Relating to Thermometry and Hydrometry

    E563 Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature

    E1137/E1137M Specification for Industrial Platinum Resistance Thermometers

    E1502 Guide for Use of Fixed-Point Cells for Reference Temperatures

    E1750 Guide for Use of Water Triple Point Cells

    E1751 Guide for Temperature Electromotive Force (EMF) Tables for Non-Letter Designated Thermocouple Combinations

    E2251 Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids