ASTM E177 - 14 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A343/A343M Standard Test Method for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method and 25-cm Epstein Test Frame

    A428/A428M Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles

    A977/A977M Standard Test Method for Magnetic Properties of High-Coercivity Permanent Magnet Materials Using Hysteresigraphs

    A1013 Standard Test Method for High-Frequency (10 kHz-1 MHz) Core Loss of Soft Magnetic Core Components at Controlled Temperatures Using the Voltmeter-Ammeter-Wattmeter Method

    A1038 Standard Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method

    B527 Standard Test Method for Determination of Tap Density of Metal Powders and Compounds

    B647 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage

    B648 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Barcol Impressor

    B703 Standard Test Method for Apparent Density of Metal Powders and Related Compounds Using the Arnold Meter

    B769 Standard Test Method for Shear Testing of Aluminum Alloys

    B795 Standard Test Method for Determining the Percentage of Alloyed or Unalloyed Iron Contamination Present in Powder Forged (PF) Steel Materials

    B886 Standard Test Method for Determination of Magnetic Saturation (Ms) of Cemented Carbides

    B887 Standard Test Method for Determination of Coercivity (Hcs) of Cemented Carbides

    C25 Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime

    C50/C50M Standard Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products

    C110 Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

    C165 Standard Test Method for Measuring Compressive Properties of Thermal Insulations

    C179 Standard Test Method for Drying and Firing Linear Change of Refractory Plastic and Ramming Mix Specimens

    C187 Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste

    C198 Standard Test Method for Cold Bonding Strength of Refractory Mortar

    C231/C231M Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

    C271/C271M Standard Test Method for Density of Sandwich Core Materials

    C272/C272M Standard Test Method for Water Absorption of Core Materials for Sandwich Constructions

    C273/C273M Standard Test Method for Shear Properties of Sandwich Core Materials

    C297/C297M Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions

    C363/C363M Standard Test Method for Node Tensile Strength of Honeycomb Core Materials

    C364/C364M Standard Test Method for Edgewise Compressive Strength of Sandwich Constructions

    C365/C365M Standard Test Method for Flatwise Compressive Properties of Sandwich Cores

    C366/C366M Standard Test Methods for Measurement of Thickness of Sandwich Cores

    C393/C393M Standard Test Method for Core Shear Properties of Sandwich Constructions by Beam Flexure

    C394/C394M Standard Test Method for Shear Fatigue of Sandwich Core Materials

    C430 Standard Test Method for Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve

    C459/C459M Standard Test Methods for Asbestos-Cement Flat Products

    C469/C469M Standard Test Method for Static Modulus of Elasticity and Poisson’s Ratio of Concrete in Compression

    C473 Standard Test Methods for Physical Testing of Gypsum Panel Products

    C474 Standard Test Methods for Joint Treatment Materials for Gypsum Board Construction

    C480/C480M Standard Test Method for Flexure Creep of Sandwich Constructions

    C534/C534M Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form

    C549 Standard Specification for Perlite Loose Fill Insulation

    C557 Standard Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing

    C586 Standard Test Method for Potential Alkali Reactivity of Carbonate Rocks as Concrete Aggregates (Rock-Cylinder Method)

    C596 Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

    C613 Standard Test Method for Constituent Content of Composite Prepreg by Soxhlet Extraction

    C651 Standard Test Method for Flexural Strength of Manufactured Carbon and Graphite Articles Using Four-Point Loading at Room Temperature

    C670 Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials

    C695 Standard Test Method for Compressive Strength of Carbon and Graphite

    C739 Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation

    C749 Standard Test Method for Tensile Stress-Strain of Carbon and Graphite

    C794 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants

    C802 Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials

    C958 Standard Test Method for Particle Size Distribution of Alumina or Quartz by X-Ray Monitoring of Gravity Sedimentation

    C1012/C1012M Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution

    C1104/C1104M Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation

    C1109 Standard Practice for Analysis of Aqueous Leachates from Nuclear Waste Materials Using Inductively Coupled Plasma-Atomic Emission Spectrometry

    C1111 Standard Test Method for Determining Elements in Waste Streams by Inductively Coupled Plasma-Atomic Emission Spectroscopy

    C1114 Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus

    C1119/C1119M Standard Test Method for Vacuum Drainage of Asbestos-Cement Mixes

    C1120/C1120M Standard Test Method for Wash Test of Asbestos

    C1121/C1121M Standard Test Method for Turner and Newall (T and N) Wet-Length Classification of Asbestos

    C1122/C1122M Standard Test Method for Wet Volume of Asbestos

    C1123/C1123M Standard Test Method for Compressibility and Recovery of Asbestos

    C1124/C1124M Standard Test Method for Kerosene Retention of Asbestos

    C1125 Standard Test Method for Penetration Index of Asbestos

    C1162/C1162M Standard Test Method for Loose Density of Asbestos

    C1174 Standard Practice for Prediction of the Long-Term Behavior of Materials, Including Waste Forms, Used in Engineered Barrier Systems (EBS) for Geological Disposal of High-Level Radioactive Waste

    C1182 Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation

    C1215 Standard Guide for Preparing and Interpreting Precision and Bias Statements in Test Method Standards Used in the Nuclear Industry

    C1234 Standard Practice for Preparation of Oils and Oily Waste Samples by High-Pressure, High-Temperature Digestion for Trace Element Determinations

    C1259 Standard Test Method for Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio for Advanced Ceramics by Impulse Excitation of Vibration

    C1274 Standard Test Method for Advanced Ceramic Specific Surface Area by Physical Adsorption

    C1275 Standard Test Method for Monotonic Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Test Specimens at Ambient Temperature

    C1285 Standard Test Methods for Determining Chemical Durability of Nuclear, Hazardous, and Mixed Waste Glasses and Multiphase Glass Ceramics: The Product Consistency Test (PCT)

    C1291 Standard Test Method for Elevated Temperature Tensile Creep Strain, Creep Strain Rate, and Creep Time-to-Failure for Advanced Monolithic Ceramics

    C1292 Standard Test Method for Shear Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures

    C1326 Standard Test Method for Knoop Indentation Hardness of Advanced Ceramics

    C1327 Standard Test Method for Vickers Indentation Hardness of Advanced Ceramics

    C1341 Standard Test Method for Flexural Properties of Continuous Fiber-Reinforced Advanced Ceramic Composites

    C1371 Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers

    C1382 Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints

    C1419 Standard Test Method for Sonic Velocity in Refractory Materials at Room Temperature and Its Use in Obtaining an Approximate Young’s Modulus

    C1421 Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature

    C1427 Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form

    C1446 Standard Test Method for Measuring Consistency of Self-Flowing Castable Refractories

    C1468 Standard Test Method for Transthickness Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperature

    C1501 Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures

    C1512 Standard Test Method for Characterizing the Effect of Exposure to Environmental Cycling on Thermal Performance of Insulation Products

    C1519 Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures

    C1606 Standard Test Method for Sampling Protocol for TCLP Testing of Container Glassware

    C1663 Standard Test Method for Measuring Waste Glass or Glass Ceramic Durability by Vapor Hydration Test

    C1667 Standard Test Method for Using Heat Flow Meter Apparatus to Measure the Center-of-Panel Thermal Resistivity of Vacuum Panels

    C1674 Standard Test Method for Flexural Strength of Advanced Ceramics with Engineered Porosity (Honeycomb Cellular Channels) at Ambient Temperatures

    C1720 Standard Test Method for Determining Liquidus Temperature of Immobilized Waste Glasses and Simulated Waste Glasses

    C1735 Standard Test Method for Measuring the Time Dependent Modulus of Sealants Using Stress Relaxation

    C1763 Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials

    D4 Standard Test Method for Bitumen Content

    D36/D36M Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)

    D198 Standard Test Methods of Static Tests of Lumber in Structural Sizes

    D465 Standard Test Methods for Acid Number of Naval Stores Products Including Tall Oil and Other Related Products

    D545 Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types)

    D628/D628M Standard Specification for Asbestos Tubular Sleeving

    D664 Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration

    D698 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft3 (600 kN-m/m3))

    D747 Standard Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam

    D854 Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer

    D1002 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)

    D1065 Standard Test Method for Unsaponifiable Matter in Naval Stores, Including Rosin, Tall Oil, and Related Products

    D1140 Standard Test Methods for Amount of Material in Soils Finer than No. 200 (75-μm) Sieve

    D1155 Standard Test Method for Roundness of Glass Spheres

    D1214 Standard Test Method for Sieve Analysis of Glass Spheres

    D1240 Standard Test Methods for Rosin Acids Content of Pine Chemicals, Including Rosin, Tall Oil, and Related Products

    D1316 Standard Test Method for Fineness of Grind of Printing Inks By the NPIRI Grindometer

    D1335 Standard Test Method for Tuft Bind of Pile Yarn Floor Coverings

    D1353 Standard Test Method for Nonvolatile Matter in Volatile Solvents for Use in Paint, Varnish, Lacquer, and Related Products

    D1518 Standard Test Method for Thermal Resistance of Batting Systems Using a Hot Plate

    D1585 Standard Test Methods for Fatty Acids Content of Naval Stores, Including Rosin, Tall Oil, and Related Products

    D1603 Standard Test Method for Carbon Black Content in Olefin Plastics

    D1709 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method

    D1822 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials

    D1894 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting

    D1934 Standard Test Method for Oxidative Aging of Electrical Insulating Petroleum Oils by Open-Beaker Method

    D1977 Standard Test Method for Nickel and Vanadium in FCC Equilibrium Catalysts by Hydrofluoric/Sulfuric Acid Decomposition and Atomic Spectroscopic Analysis

    D2013/D2013M Standard Practice for Preparing Coal Samples for Analysis

    D2065 : Standard Test Method for Determination of Edge Performance of Composite Wood Products Under Surfactant Accelerated Moisture Stress

    D2124 Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique

    D2166/D2166M Standard Test Method for Unconfined Compressive Strength of Cohesive Soil

    D2238 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1

    D2344/D2344M Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates

    D2369 Standard Test Method for Volatile Content of Coatings

    D2412 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2589/D2589M Standard Test Method for McNett Wet Classification of Dual Asbestos Fiber

    D2752/D2752M Standard Test Methods for Air Permeability of Asbestos Fibers

    D2777 Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water

    D2799 Standard Test Method for Microscopical Determination of the Maceral Composition of Coal

    D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants

    D2854 Standard Test Method for Apparent Density of Activated Carbon

    D2862 Standard Test Method for Particle Size Distribution of Granular Activated Carbon

    D2865M Standard Practice for Calibration of Standards and Equipment for Electrical Insulating Materials Testing

    D2866 Standard Test Method for Total Ash Content of Activated Carbon

    D2867 Standard Test Methods for Moisture in Activated Carbon

    D2868 Standard Test Method for Nitrogen Content (Kjeldahl) and Hide Substance Content of Leather

    D2885 Standard Test Method for Determination of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct Comparison Technique

    D2947/D2947M Standard Test Method for Screen Analysis of Asbestos Fibers

    D3039/D3039M Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials

    D3124 Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry

    D3159 Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials

    D3171 Standard Test Methods for Constituent Content of Composite Materials

    D3241 Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels

    D3249 Standard Practice for General Ambient Air Analyzer Procedures

    D3273 Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber

    D3307 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials

    D3321 Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants

    D3364 Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications

    D3389 Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)

    D3410/D3410M Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading

    D3420 Standard Test Method for Pendulum Impact Resistance of Plastic Film

    D3465 Standard Test Method for Purity of Monomeric Plasticizers by Gas Chromatography

    D3479/D3479M Standard Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materials

    D3498 Standard Specification for Adhesives for Field-Gluing Plywood to Lumber Framing for Floor Systems

    D3518/D3518M Standard Test Method for In-Plane Shear Response of Polymer Matrix Composite Materials by Tensile Test of a ±45° Laminate

    D3529M Standard Test Method for Matrix Solids Content and Matrix Content of Composite Prepreg

    D3530 Standard Test Method for Volatiles Content of Composite Material Prepreg

    D3552 Standard Test Method for Tensile Properties of Fiber Reinforced Metal Matrix Composites

    D3575 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers

    D3594 Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers

    D3639/D3639M Standard Test Method for Classification of Asbestos by Quebec Standard Test

    D3663 Standard Test Method for Surface Area of Catalysts and Catalyst Carriers

    D3670 Standard Guide for Determination of Precision and Bias of Methods of Committee D22

    D3752 Standard Test Method for Strength Imparted by Asbestos to a Cementitious Matrix

    D3773/D3773M Standard Test Methods for Length of Woven Fabric

    D3800M Standard Test Method for Density of High-Modulus Fibers

    D3906 Standard Test Method for Determination of Relative X-ray Diffraction Intensities of Faujasite-Type Zeolite-Containing Materials

    D3907/D3907M Standard Test Method for Testing Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test

    D3908 Standard Test Method for Hydrogen Chemisorption on Supported Platinum Catalysts by Volumetric Vacuum Method

    D3936 Standard Test Method for Resistance to Delamination of the Secondary Backing of Pile Yarn Floor Covering

    D3953 Standard Specification for Strapping, Flat Steel and Seals

    D3963/D3963M Standard Specification for Fabrication and Jobsite Handling of Epoxy-Coated Steel Reinforcing Bars

    D4058 Standard Test Method for Attrition and Abrasion of Catalysts and Catalyst Carriers

    D4085 Standard Test Method for Metals in Cellulose by Atomic Absorption Spectrophotometry

    D4094 Standard Test Method for Acid Content of Ethylene-Acrylic Acid Copolymers

    D4164 Standard Test Method for Mechanically Tapped Packing Density of Formed Catalyst and Catalyst Carriers

    D4179 Standard Test Method for Single Pellet Crush Strength of Formed Catalysts and Catalyst Carriers

    D4180 Standard Test Method for Vibratory Packing Density of Formed Catalyst Particles and Catalyst Carriers

    D4222 Standard Test Method for Determination of Nitrogen Adsorption and Desorption Isotherms of Catalysts and Catalyst Carriers by Static Volumetric Measurements

    D4253 Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table

    D4254 Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density

    D4255/D4255M Standard Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method

    D4280 Standard Specification for Extended Life Type, Nonplowable, Raised Retroreflective Pavement Markers

    D4284 Standard Test Method for Determining Pore Volume Distribution of Catalysts and Catalyst Carriers by Mercury Intrusion Porosimetry

    D4318 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils

    D4365 Standard Test Method for Determining Micropore Volume and Zeolite Area of a Catalyst

    D4430 Standard Practice for Determining the Operational Comparability of Meteorological Measurements

    D4438 Standard Test Method for Particle Size Distribution of Catalysts and Catalyst Carriers by Electronic Counting

    D4460 Standard Practice for Calculating Precision Limits Where Values are Calculated from Other Test Methods

    D4463/D4463M Standard Guide for Metals Free Steam Deactivation of Fresh Fluid Cracking Catalysts

    D4464 Standard Test Method for Particle Size Distribution of Catalytic Material by Laser Light Scattering

    D4481 Standard Test Method for Total Nickel in Fresh Alumina-Base Catalysts

    D4497 Standard Test Method for Determining the Open Time of Hot Melt Adhesives (Manual Method)

    D4512 Standard Test Method for Vibrated Apparent Packing Density of Fine Catalyst and Catalyst Carrier Particles and Powder

    D4513 Standard Test Method for Particle Size Distribution of Catalytic Materials by Sieving

    D4562 Standard Test Method for Shear Strength of Adhesives Using Pin-and-Collar Specimen

    D4567 Standard Test Method for Single-Point Determination of Specific Surface Area of Catalysts and Catalyst Carriers Using Nitrogen Adsorption by Continuous Flow Method

    D4607 Standard Test Method for Determination of Iodine Number of Activated Carbon

    D4642 Standard Test Method for Platinum in Reforming Catalysts by Wet Chemistry

    D4699 Standard Test Method for Vibratory Packing Density of Large Formed Catalyst and Catalyst Carrier Particles

    D4735 Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography

    D4761 Standard Test Methods for Mechanical Properties of Lumber and Wood-Base Structural Material

    D4780 Standard Test Method for Determination of Low Surface Area of Catalysts and Catalyst Carriers by Multipoint Krypton Adsorption

    D4781 Standard Test Method for Mechanically Tapped Packing Density of Fine Catalyst Particles and Catalyst Carrier Particles

    D4782 Standard Test Method for Palladium in Molecular Sieve Catalyst by Wet Chemistry

    D4796 Standard Test Method for Bond Strength of Thermoplastic Traffic Marking Materials

    D4797 Standard Test Methods for Gravimetric Analysis of White and Yellow Thermoplastic Traffic Marking

    D4890 Standard Test Methods for Polyurethane Raw Materials: Determination of Gardner and APHA Color of Polyols

    D4894 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials

    D4895 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion

    D4944 Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester

    D5017 Standard Test Method for Determination of Linear Low Density Polyethylene (LLDPE) Composition by Carbon-13 Nuclear Magnetic Resonance

    D5029 Standard Test Method for Water Solubles in Activated Carbon

    D5084 Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter

    D5147/D5147M Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material

    D5153 Standard Test Method for Palladium in Molecular Sieve Catalyst by Atomic Absorption

    D5154 Standard Test Method for Determining Activity and Selectivity of Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test

    D5158 Standard Test Method for Determination of Particle Size of Powdered Activated Carbon by Air Jet Sieving

    D5197 Standard Test Method for Determination of Formaldehyde and Other Carbonyl Compounds in Air (Active Sampler Methodology)

    D5228 Standard Test Method for Determination of Butane Working Capacity of Activated Carbon

    D5280 Standard Practice for Evaluation of Performance Characteristics of Air Quality Measurement Methods with Linear Calibration Functions

    D5314 Standard Guide for Soil Gas Monitoring in the Vadose Zone

    D5357 Standard Test Method for Determination of Relative Crystallinity of Zeolite Sodium A by X-ray Diffraction

    D5379/D5379M Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method

    D5403 Standard Test Methods for Volatile Content of Radiation Curable Materials

    D5448/D5448M Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders

    D5449/D5449M Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders

    D5450/D5450M Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders

    D5467/D5467M Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam

    D5504 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence

    D5528 Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites

    D5572 Standard Specification for Adhesives Used for Finger Joints in Nonstructural Lumber Products

    D5594 Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR)

    D5649 Standard Test Method for Torque Strength of Adhesives Used on Threaded Fasteners

    D5681 Standard Terminology for Waste and Waste Management

    D5742 Standard Test Method for Determination of Butane Activity of Activated Carbon

    D5751 Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber Products

    D5755 Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number Surface Loading

    D5757 Standard Test Method for Determination of Attrition and Abrasion of Powdered Catalysts by Air Jets

    D5758 Standard Test Method for Determination of Relative Crystallinity of Zeolite ZSM-5 by X-Ray Diffraction

    D5766/D5766M Standard Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite Laminates

    D5768 Standard Test Method for Determination of Iodine Value of Tall Oil Fatty Acids

    D5795 Standard Test Method for Determination of Liquid Water Absorption of Coated Hardboard and Other Composite Wood Products Via “Cobb Ring” Apparatus

    D5824 Standard Test Method for Determining Resistance to Delamination of Adhesive Bonds in Overlay-Wood Core Laminates Exposed to Heat and Water

    D5827 Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography

    D5831 Standard Test Method for Screening Fuels in Soils

    D5867 Standard Test Methods for Measurement of Physical Properties of Raw Cotton by Cotton Classification Instruments

    D5930 Standard Test Method for Thermal Conductivity of Plastics by Means of a Transient Line-Source Technique

    D5961/D5961M Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates

    D5994 Standard Test Method for Measuring Core Thickness of Textured Geomembrane

    D6004 Standard Test Method for Determining Adhesive Shear Strength of Carpet Adhesives

    D6037 Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings

    D6090 Standard Test Method for Softening Point Resins (Mettler Cup and Ball Method)

    D6115 Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites

    D6130 Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy

    D6132 Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage

    D6133 Standard Test Method for Acetone, p-Chlorobenzotrifluoride, Methyl Acetate or t-Butyl Acetate Content of Solventborne and Waterborne Paints, Coatings, Resins, and Raw Materials by Direct Injection Into a Gas Chromatograph

    D6166 Standard Test Method for Color of Pine Chemicals and Related Products (Instrumental Determination of Gardner Color)

    D6175 Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles

    D6195 Standard Test Methods for Loop Tack

    D6248 Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry

    D6264/D6264M Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer-Matrix Composite to a Concentrated Quasi-Static Indentation Force

    D6281 Standard Test Method for Airborne Asbestos Concentration in Ambient and Indoor Atmospheres as Determined by Transmission Electron Microscopy Direct Transfer (TEM)

    D6299 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance

    D6415/D6415M Standard Test Method for Measuring the Curved Beam Strength of a Fiber-Reinforced Polymer-Matrix Composite

    D6463/D6463M Standard Test Method for Time to Failure of Pressure Sensitive Articles Under Sustained Shear Loading

    D6464 Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing

    D6469 Standard Guide for Microbial Contamination in Fuels and Fuel Systems

    D6484/D6484M Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates

    D6493 Standard Test Methods for Softening Point of Hydrocarbon Resins and Rosin Based Resins by Automated Ring-and-Ball Apparatus

    D6566 Standard Test Method for Measuring Mass per Unit Area of Turf Reinforcement Mats

    D6567 Standard Test Method for Measuring the Light Penetration of a Turf Reinforcement Mat (TRM)

    D6576 Standard Specification for Flexible Cellular Rubber Chemically Blown

    D6583 Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption

    D6607 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits

    D6631 Standard Guide for Committee D01 for Conducting an Interlaboratory Study for the Purpose of Determining the Precision of a Test Method

    D6641/D6641M Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture

    D6645 Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry

    D6647 Standard Test Method for Determination of Acid Soluble Iron Via Atomic Absorption

    D6671/D6671M Standard Test Method for Mixed Mode I-Mode II Interlaminar Fracture Toughness of Unidirectional Fiber Reinforced Polymer Matrix Composites

    D6738 Standard Test Method for Precipitated Silica - Volatile Content

    D6739 Standard Test Method for Silica - pH Value

    D6740 Standard Test Method for Silanes Used in Rubber Formulations (bis-(triethoxysilylpropyl)sulfanes): Residue on Ignition

    D6741 Standard Test Methods for Silanes Used in Rubber Formulations (bis-(triethoxysilylpropyl)sulfanes): Sulfur Content

    D6742/D6742M Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates

    D6761 Standard Test Method for Determination of the Total Pore Volume of Catalysts and Catalyst Carriers

    D6790/D6790M Standard Test Method for Determining Poisson's Ratio of Honeycomb Cores

    D6792 Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories

    D6809 Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials

    D6815 Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products

    D6817/D6817M Standard Specification for Rigid Cellular Polystyrene Geofoam

    D6843 Standard Test Method for Silanes Used in Rubber Formulations (bis-(triethoxysilylpropyl)sulfanes): Characterization by Gas Chromatography (GC)

    D6844 Standard Test Method for Silanes Used in Rubber Formulations (bis-(triethoxysilylpropyl)sulfanes): Characterization by High Performance Liquid Chromatography (HPLC)

    D6845 Standard Test Method for Silica, Precipitated, Hydrated—CTAB (Cetyltrimethylammonium Bromide) Surface Area

    D6854 Standard Test Method for Silica-Oil Absorption Number

    D6862 Standard Test Method for 90 Degree Peel Resistance of Adhesives

    D6873/D6873M Standard Practice for Bearing Fatigue Response of Polymer Matrix Composite Laminates

    D6883 Standard Practice for Manual Sampling of Stationary Coal from Railroad Cars, Barges, Trucks, or Stockpiles

    D6886 Standard Test Method for Determination of the Weight Percent Individual Volatile Organic Compounds in Waterborne Air-Dry Coatings by Gas Chromatography

    D6900 Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate

    D6906 Standard Test Method for Determination of Titanium Treatment Weight on Metal Substrates by Wavelength Dispersive X-Ray Fluorescence

    D6913 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis

    D7011 Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography and Sulfur Selective Detection

    D7027 Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine

    D7028 Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)

    D7078/D7078M Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method

    D7084 Standard Test Method for Determination of Bulk Crush Strength of Catalysts and Catalyst Carriers

    D7136/D7136M Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event

    D7137/D7137M Standard Test Method for Compressive Residual Strength Properties of Damaged Polymer Matrix Composite Plates

    D7191 Standard Test Method for Determination of Moisture in Plastics by Relative Humidity Sensor

    D7202 Standard Test Method for Determination of Beryllium in the Workplace by Extraction and Optical Fluorescence Detection

    D7234 Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers

    D7245 Standard Test Method for Measuring Total Water and Volatiles in Liquid Coatings Which Produce Cure Water Upon Heating

    D7248/D7248M Standard Test Method for Bearing/Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens

    D7249/D7249M Standard Test Method for Facing Properties of Sandwich Constructions by Long Beam Flexure

    D7250/D7250M Standard Practice for Determining Sandwich Beam Flexural and Shear Stiffness

    D7264/D7264M Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials

    D7291/D7291M Standard Test Method for Through-Thickness "Flatwise" Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material

    D7309 Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry

    D7313 Standard Test Method for Determining Fracture Energy of Asphalt-Aggregate Mixtures Using the Disk-Shaped Compact Tension Geometry

    D7330 Standard Test Method for Assessment of Surface Appearance Change in Pile Floor Coverings Using Standard Reference Scales

    D7332/D7332M Standard Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite

    D7336/D7336M Standard Test Method for Static Energy Absorption Properties of Honeycomb Sandwich Core Materials

    D7360 Standard Test Method for Analysis of Benzene by Gas Chromatography with External Calibration

    D7372 Standard Guide for Analysis and Interpretation of Proficiency Test Program Results

    D7426 Standard Test Method for Assignment of the DSC Procedure for Determining Tg of a Polymer or an Elastomeric Compound

    D7430 Standard Practice for Mechanical Sampling of Coal

    D7448 Standard Practice for Establishing the Competence of Laboratories Using ASTM Procedures in the Sampling and Analysis of Coal and Coke

    D7458 Standard Test Method for Determination of Beryllium in Soil, Rock, Sediment, and Fly Ash Using Ammonium Bifluoride Extraction and Fluorescence Detection

    D7466 Standard Test Method for Measuring the Asperity Height of Textured Geomembrane

    D7469 Standard Test Methods for End-Joints in Structural Wood Products

    D7471 Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials

    D7472 Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials

    D7476 Standard Test Method for Brine Saturation Value of Cured (Salt-Preserved) Hides and Skins

    D7477 Standard Test Method for Determining the Area Stability of Wet Blue Submersed in Boiling Water

    D7488 Standard Test Method for Open Time of Latex Paints

    D7504 Standard Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and Effective Carbon Number

    D7514 Standard Test Method for Evaluating Ink Stainblocking of Architectural Paint Systems by Visual Assessment

    D7515 Standard Test Method for Purity of 1,3-Propanediol (Gas Chromatographic Method)

    D7553 Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide

    D7565/D7565M Standard Test Method for Determining Tensile Properties of Fiber Reinforced Polymer Matrix Composites Used for Strengthening of Civil Structures

    D7570 Standard Test Method for Evaluation of Dimensional Stability of Pile Yarn Floor Covering

    D7577 Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends

    D7584 Standard Test Method for Evaluating the Resistance of the Surface of Wet Blue to the Growth of Fungi in an Environmental Chamber

    D7591 Standard Test Method for Determination of Free and Total Glycerin in Biodiesel Blends by Anion Exchange Chromatography

    D7615/D7615M Standard Practice for Open-Hole Fatigue Response of Polymer Matrix Composite Laminates

    D7616/D7616M Standard Test Method for Determining Apparent Overlap Splice Shear Strength Properties of Wet Lay-Up Fiber-Reinforced Polymer Matrix Composites Used for Strengthening Civil Structures

    D7635/D7635M Standard Test Method for Measurement of Thickness of Coatings Over Fabric Reinforcement

    D7637 Standard Test Method for Determination of Glycerin Assay by Titration (Sodium Meta Periodate)

    D7639 Standard Test Method for Determination of Zirconium Treatment Weight or Thickness on Metal Substrates by X-Ray Fluorescence

    D7661 Standard Test Method for Determining Compatibility of Personal Lubricants with Natural Rubber Latex Condoms

    D7674 Standard Test Method for Hexane/Petroleum Ether Extract in Wet Blue and Wet White

    D7681 Standard Test Method for Measuring Gradation of Glass Spheres Using a Flowing Stream Digital Image Analyzer

    D7682 Standard Test Method for Replication and Measurement of Concrete Surface Profiles Using Replica Putty

    D7708 Standard Test Method for Microscopical Determination of the Reflectance of Vitrinite Dispersed in Sedimentary Rocks

    D7713 Standard Specification for Aqueous Engine Coolant Grade Glycol (53% Nominal)

    D7716 Standard Test Method for Determination of Residual Methanol in Glycerin by Gas Chromatography

    D7735 Standard Test Method for Type A Durometer Hardness Testing of Road Marking Thermoplastic at Elevated Temperatures

    D7736 Standard Test Method for Determination of Acids and Glycol Esters in Ethylene Glycol

    D7744/D7744M Standard Test Methods for Tensile Testing of High Performance Polyethylene Tapes

    D7748/D7748M Standard Test Method for Flexural Rigidity of Geogrids, Geotextiles and Related Products

    D7766/D7766M Standard Practice for Damage Resistance Testing of Sandwich Constructions

    D7767 Standard Test Method to Measure Volatiles from Radiation Curable Acrylate Monomers, Oligomers, and Blends and Thin Coatings Made from Them

    D7768 Standard Test Method for Speciated Organic Volatile Content of Waterborne Multi-Component Coatings by Gas Chromatography

    D7778 Standard Guide for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

    D7779 Standard Test Method for Determination of Fracture Toughness of Graphite at Ambient Temperature

    D7785 Standard Test Method for Water in Lint Cotton by Oven Evaporation Combined with Volumetric Karl Fischer Titration

    D7786 Standard Test Method for Determining Enamel Holdout

    D7811 Standard Test Method for Bow and Skew Using a Measuring Tool

    D7816 Standard Test Method for Enumeration of Halophilic and Proteolytic Bacteria in Raceway Brine, Brine-Cured Hides and Skins

    D7817 Standard Test Method for Enumeration of Yeast and Mold in Raceway Brine, Brine-Cured Hides and Skins

    D7818 Standard Test Method for Enumeration of Proteolytic Bacteria in Fresh (Uncured) Hides and Skins

    D7819 Standard Test Method for Enumeration of Yeast and Mold on Fresh (Uncured) Hides and Skins

    D7823 Standard Test Method for Determination of Low Level, Regulated Phthalates in Poly (Vinyl Chloride) Plastics by Thermal Desorption—Gas Chromatography/Mass Spectrometry

    D7843 Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry

    D7855/D7855M Standard Test Method for Determination of Mold Growth on Coated Building Products Designed for Interior Applications Using an Environmental Chamber and Indirect Inoculation

    D7881 Standard Test Method for Determination of 4-Carboxybenzaldehyde and p-Toluic Acid in Purified Terephthalic Acid by Capillary Electrophoresis with Reverse Voltage Mode

    D7882 Standard Test Method for Determination of 4-Carboxybenzaldehyde and p-Toluic Acid in Purified Terephthalic Acid by Capillary Electrophoresis with Normal Voltage Mode

    D7883 Standard Test Method for Determination of 4-Carboxybenzaldehyde and p-Toluic Acid in Purified Terephthalic Acid by Weak Anion Exchange High Performance Liquid Chromatography

    D7884 Standard Test Method for Determination of 4-Carboxybenzaldehyde and p-Toluic Acid in Purified Terephthalic Acid by Reverse Phase High Performance Liquid Chromatography

    E9 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature

    E21 Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials

    E23 Standard Test Methods for Notched Bar Impact Testing of Metallic Materials

    E28 Standard Test Methods for Softening Point of Resins Derived from Pine Chemicals and Hydrocarbons, by Ring-and-Ball Apparatus

    E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E96/E96M Standard Test Methods for Water Vapor Transmission of Materials

    E119 Standard Test Methods for Fire Tests of Building Construction and Materials

    E139 Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials

    E262 Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques

    E292 Standard Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials

    E384 Standard Test Method for Knoop and Vickers Hardness of Materials

    E398 Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement

    E399 Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness KIc of Metallic Materials

    E430 Standard Test Methods for Measurement of Gloss of High-Gloss Surfaces by Abridged Goniophotometry

    E481 Standard Test Method for Measuring Neutron Fluence Rate by Radioactivation of Cobalt and Silver

    E517 Standard Test Method for Plastic Strain Ratio r for Sheet Metal

    E572 Standard Test Method for Analysis of Stainless and Alloy Steels by Wavelength Dispersive X-Ray Fluorescence Spectrometry

    E595 Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment

    E606/E606M Standard Test Method for Strain-Controlled Fatigue Testing

    E643 Standard Test Method for Ball Punch Deformation of Metallic Sheet Material

    E646 Standard Test Method for Tensile Strain-Hardening Exponents (n -Values) of Metallic Sheet Materials

    E660 Standard Practice for Accelerated Polishing of Aggregates or Pavement Surfaces Using a Small-Wheel, Circular Track Polishing Machine

    E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

    E766 Standard Practice for Calibrating the Magnification of a Scanning Electron Microscope

    E826 Standard Practice for Testing Homogeneity of a Metal Lot or Batch in Solid Form by Spark Atomic Emission Spectrometry

    E834 Standard Practice for Determining Vacuum Chamber Gaseous Environment Using a Cold Finger

    E839 Standard Test Methods for Sheathed Thermocouples and Sheathed Thermocouple Cable

    E855 Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading

    E970 Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

    E1082 Standard Test Method for Measurement of Vehicular Response to Traveled Surface Roughness

    E1260 Standard Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments

    E1354 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter

    E1356 Standard Test Method for Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry

    E1367 Standard Test Method for Measuring the Toxicity of Sediment-Associated Contaminants with Estuarine and Marine Invertebrates

    E1414/E1414M Standard Test Method for Airborne Sound Attenuation Between Rooms Sharing a Common Ceiling Plenum

    E1488 Standard Guide for Statistical Procedures to Use in Developing and Applying Test Methods

    E1489 Standard Practice for Computing Ride Number of Roads from Longitudinal Profile Measurements Made by an Inertial Profile Measuring Device

    E1574 Standard Test Method for Measurement of Sound in Residential Spaces

    E1601 Standard Practice for Conducting an Interlaboratory Study to Evaluate the Performance of an Analytical Method

    E1617 Standard Practice for Reporting Particle Size Characterization Data

    E1706 Standard Test Method for Measuring the Toxicity of Sediment-Associated Contaminants with Freshwater Invertebrates

    E1710 Standard Test Method for Measurement of Retroreflective Pavement Marking Materials with CEN-Prescribed Geometry Using a Portable Retroreflectometer

    E1719 Standard Test Method for Vapor Pressure of Liquids by Ebulliometry

    E1732 Standard Terminology Relating to Forensic Science

    E1782 Standard Test Method for Determining Vapor Pressure by Thermal Analysis

    E1834 Standard Test Method for Analysis of Nickel Alloys by Graphite Furnace Atomic Absorption Spectrometry

    E1868 Standard Test Method for Loss-On-Drying by Thermogravimetry

    E1875 Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Sonic Resonance

    E1876 Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Impulse Excitation of Vibration

    E1921 Standard Test Method for Determination of Reference Temperature, To, for Ferritic Steels in the Transition Range

    E1926 Standard Practice for Computing International Roughness Index of Roads from Longitudinal Profile Measurements

    E1927 Standard Guide for Conducting Subjective Pavement Ride Quality Ratings

    E1965 Standard Specification for Infrared Thermometers for Intermittent Determination of Patient Temperature

    E1970 Standard Practice for Statistical Treatment of Thermoanalytical Data

    E2008 Standard Test Methods for Volatility Rate by Thermogravimetry

    E2161 Standard Terminology Relating to Performance Validation in Thermal Analysis

    E2171 Standard Practice for Rating-Scale Measures Relevant to the Electronic Health Record

    E2177 Standard Test Method for Measuring the Coefficient of Retroreflected Luminance (RL) of Pavement Markings in a Standard Condition of Wetness

    E2248 Standard Test Method for Impact Testing of Miniaturized Charpy V-Notch Specimens

    E2253 Standard Test Method for Temperature and Enthalpy Measurement Validation of Differential Scanning Calorimeters

    E2269 Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units using Gas Chromatography

    E2274 Standard Test Method for Evaluation of Laundry Sanitizers and Disinfectants

    E2282 Standard Guide for Defining the Test Result of a Test Method

    E2298 Standard Test Method for Instrumented Impact Testing of Metallic Materials

    E2330 Standard Test Method for Determination of Concentrations of Elements in Glass Samples Using Inductively Coupled Plasma Mass Spectrometry (ICP-MS) for Forensic Comparisons

    E2399 Standard Test Method for Maximum Media Density for Dead Load Analysis of Vegetative (Green) Roof Systems

    E2402 Standard Test Method for Mass Loss and Residue Measurement Validation of Thermogravimetric Analyzers

    E2406 Standard Test Method for Evaluation of Laundry Sanitizers and Disinfectants for Use in High Efficiency Washing Operations

    E2427 Standard Test Method for Acceptance by Performance Testing for Sieves

    E2448 Standard Test Method for Determining the Superplastic Properties of Metallic Sheet Materials

    E2455 Standard Guide for Conducting Laboratory Toxicity Tests with Freshwater Mussels

    E2480 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method with Multi-Valued Measurands

    E2489 Standard Practice for Statistical Analysis of One-Sample and Two-Sample Interlaboratory Proficiency Testing Programs

    E2490 Standard Guide for Measurement of Particle Size Distribution of Nanomaterials in Suspension by Photon Correlation Spectroscopy (PCS)

    E2532 Standard Test Methods for Evaluating Performance of Highway Traffic Monitoring Devices

    E2551 Standard Test Method for Humidity Calibration (or Conformation) of Humidity Generators for Use with Thermogravimetric Analyzers

    E2554 Standard Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method Using Control Chart Techniques

    E2584 Standard Practice for Thermal Conductivity of Materials Using a Thermal Capacitance (Slug) Calorimeter

    E2591 Standard Guide for Conducting Whole Sediment Toxicity Tests with Amphibians

    E2627 Standard Practice for Determining Average Grain Size Using Electron Backscatter Diffraction (EBSD) in Fully Recrystallized Polycrystalline Materials

    E2649 Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy

    E2653 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Fire Test Method with Fewer Than Six Participating Laboratories

    E2655 Standard Guide for Reporting Uncertainty of Test Results and Use of the Term Measurement Uncertainty in ASTM Test Methods

    E2677 Standard Test Method for Determining Limits of Detection in Explosive Trace Detectors

    E2694 Standard Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids

    E2714 Standard Test Method for Creep-Fatigue Testing

    E2759 Standard Practice for Highway Traffic Monitoring Truth-in-Data

    E2760 Standard Test Method for Creep-Fatigue Crack Growth Testing

    E2782 Standard Guide for Measurement Systems Analysis (MSA)

    E2792 Standard Test Method for Determination of Hydrogen in Aluminum and Aluminum Alloys by Inert Gas Fusion

    E2798 Standard Test Method for Characterization of Performance of Pesticide Spray Drift Reduction Adjuvants for Ground Application

    E2823 Standard Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Mass Spectrometry (Performance-Based Method)

    E2832 Standard Test Method for Measuring the Coefficient of Retroreflected Luminance of Pavement Markings in a Standard Condition of Continuous Wetting (RL-2)

    E2916 Standard Terminology for Digital and Multimedia Evidence Examination

    E2926 Standard Test Method for Forensic Comparison of Glass Using Micro X-ray Fluorescence (µ-XRF) Spectrometry

    E2927 Standard Test Method for Determination of Trace Elements in Soda-Lime Glass Samples Using Laser Ablation Inductively Coupled Plasma Mass Spectrometry for Forensic Comparisons

    E2931 Standard Test Method for Limiting Oxygen (Oxidant) Concentration of Combustible Dust Clouds

    E2935 Standard Practice for Conducting Equivalence Testing in Laboratory Applications

    F218 Standard Test Method for Measuring Optical Retardation and Analyzing Stress in Glass

    F386 Standard Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces

    F387 Standard Test Method for Measuring Thickness of Resilient Floor Covering With Foam Layer

    F558 Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaners

    F608 Standard Test Method for Evaluation of Carpet Embedded Dirt Removal Effectiveness of Household/Commercial Vacuum Cleaners

    F739 Standard Test Method for Permeation of Liquids and Gases through Protective Clothing Materials under Conditions of Continuous Contact

    F820 Standard Test Method for Measuring Air Performance Characteristics of Central Vacuum Cleaning Systems

    F948 Standard Test Method for Time-to-Failure of Plastic Piping Systems and Components Under Constant Internal Pressure With Flow

    F1165 Standard Test Method for Measuring Angular Displacement of Multiple Images in Transparent Parts

    F1249 Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor

    F1284 Standard Test Method for Evaluating Carpet Embedded Dirt Removal Effectiveness of Residential Central Vacuum Cleaning Systems

    F1326 Standard Test Method for Measuring Maximum Dry Volume of Utility Vacuum Cleaners

    F1334 Standard Test Method for Determining A-Weighted Sound Power Level of Vacuum Cleaners

    F1383 Standard Test Method for Permeation of Liquids and Gases through Protective Clothing Materials under Conditions of Intermittent Contact

    F1404 Test Method for Crystallographic Perfection of Gallium Arsenide by Molten Potassium Hydroxide (KOH) Etch Technique

    F1498 Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings

    F1514 Standard Test Method for Measuring Heat Stability of Resilient Flooring by Color Change

    F1515 Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change

    F1520 Standard Test Method for Determining the Drive Torque for Film and Fabric Ribbon Cartridges

    F1593 Standard Test Method for Trace Metallic Impurities in Electronic Grade Aluminum by High Mass-Resolution Glow-Discharge Mass Spectrometer

    F1608 Standard Test Method for Microbial Ranking of Porous Packaging Materials (Exposure Chamber Method)

    F1632 Standard Test Method for Particle Size Analysis and Sand Shape Grading of Golf Course Putting Green and Sports Field Rootzone Mixes

    F1645/F1645M Standard Test Method for Water Migration in Honeycomb Core Materials

    F1647 Standard Test Methods for Organic Matter Content of Athletic Field Rootzone Mixes

    F1702 Standard Test Method for Measuring Impact-Attenuation Characteristics of Natural Playing Surface Systems Using a Lightweight Portable Apparatus

    F1717 Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model

    F1863 Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmisivity of Transparent Parts

    F1868 Standard Test Method for Thermal and Evaporative Resistance of Clothing Materials Using a Sweating Hot Plate

    F1884 Standard Test Method for Determining Residual Solvents in Packaging Materials

    F1888 Standard Test Method for Compression-Displacement of Baseballs and Softballs

    F1930 Standard Test Method for Evaluation of Flame Resistant Clothing for Protection Against Fire Simulations Using an Instrumented Manikin

    F1940 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

    F1951 Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment

    F2082 Standard Test Method for Determination of Transformation Temperature of Nickel-Titanium Shape Memory Alloys by Bend and Free Recovery

    F2095 Standard Test Methods for Pressure Decay Leak Test for Flexible Packages With and Without Restraining Plates

    F2105 Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaner Motor/Fan Systems

    F2129 Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements to Determine the Corrosion Susceptibility of Small Implant Devices

    F2150 Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Tissue-Engineered Medical Products

    F2156 Standard Test Method for Measuring Optical Distortion in Transparent Parts Using Grid Line Slope

    F2157 Standard Specification for Synthetic Surfaced Running Tracks

    F2199 Standard Test Method for Determining Dimensional Stability of Resilient Floor Tile after Exposure to Heat

    F2385 Standard Test Method for Determining Femoral Head Penetration into Acetabular Components of Total Hip Replacement Using Clinical Radiographs

    F2466 Standard Practice for Determining Silicone Volatiles in Silicone Rubber for Transportation Applications

    F2476 Standard Test Method for the Determination of Carbon Dioxide Gas Transmission Rate (CO2TR) Through Barrier Materials Using An Infrared Detector

    F2516 Standard Test Method for Tension Testing of Nickel-Titanium Superelastic Materials

    F2544 Standard Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power Units

    F2569 Standard Test Method for Evaluating the Force Reduction Properties of Surfaces for Athletic Use

    F2607 Standard Test Method for Measuring the Hard Surface Floor-Cleaning Ability of Household/Commercial Vacuum Cleaners

    F2609 Standard Test Method for Litter-Cleaning Effectiveness of Vacuum Cleaners

    F2634 Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method

    F2638 Standard Test Method for Using Aerosol Filtration for Measuring the Performance of Porous Packaging Materials as a Surrogate Microbial Barrier

    F2797 Standard Test Method for Evaluating Edge Cleaning Effectiveness of Vacuum Cleaners

    F2824 Standard Test Method for Mechanical Seal Strength Testing for Round Cups and Bowl Containers with Flexible Peelable Lids

    F2826 Standard Test Method for Evaluating the Sustained Air Performance and Exhaust Emission Efficiencies of Central Vacuum Cleaning Units

    F2828 Standard Test Method for Assessing Carpet Cleaning Effectiveness in Terms of Visual Appearance Change When Cleaned with a Wet Extraction Cleaning System

    F2837 Standard Test Method for Hot Compression Properties of Gasket Materials

    F2845 Standard Test Method for Measuring the Dynamic Stiffness (DS) and Cylindrical Coefficient of Restitution (CCOR) of Baseballs and Softballs

    F2883 Standard Guide for Characterization of Ceramic and Mineral Based Scaffolds used for Tissue-Engineered Medical Products (TEMPs) and as Device for Surgical Implant Applications

    F2894 Standard Test Method for Evaluation of Materials, Protective Clothing and Equipment for Heat Resistance Using a Hot Air Circulating Oven

    F2961 Standard Test Method for Characterizing Gripping Performance of Gloves Using a Torque Meter

    F2980 Standard Test Method for Analysis of Heavy Metals in Glass by Field Portable X-Ray Fluorescence (XRF)

    F3004 Standard Test Method for Evaluation of Seal Quality and Integrity Using Airborne Ultrasound

    F3022 Standard Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments

    F3030 Standard Test Method for Snowboards with a Channel-Mounting System and Removable Inserts

    F3079 Standard Practice for Use of Distributed Optical Fiber Sensing Systems for Monitoring the Impact of Ground Movements During Tunnel and Utility Construction on Existing Underground Utilities

    G32 Standard Test Method for Cavitation Erosion Using Vibratory Apparatus

    G51 Standard Test Method for Measuring pH of Soil for Use in Corrosion Testing

    G65 Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus

    G72/G72M Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment

    G73 Standard Test Method for Liquid Impingement Erosion Using Rotating Apparatus

    G77 Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test

    G105 Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests

    G109 Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments

    G117 Standard Guide for Calculating and Reporting Measures of Precision Using Data from Interlaboratory Wear or Erosion Tests

    G122 Standard Test Method for Evaluating the Effectiveness of Cleaning Agents

    G132 Standard Test Method for Pin Abrasion Testing

    G141 Standard Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials

    G143 Standard Test Method for Measurement of Web/Roller Friction Characteristics

    G150 Standard Test Method for Electrochemical Critical Pitting Temperature Testing of Stainless Steels

    G156 Standard Practice for Selecting and Characterizing Weathering Reference Materials

    G174 Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact

    G176 Standard Test Method for Ranking Resistance of Plastics to Sliding Wear using Block-on-Ring Wear Test—Cumulative Wear Method

    G181 Standard Test Method for Conducting Friction Tests of Piston Ring and Cylinder Liner Materials Under Lubricated Conditions


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    E456 Terminology Relating to Quality and Statistics

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

    E1488 Guide for Statistical Procedures to Use in Developing and Applying Test Methods

    E2282 Guide for Defining the Test Result of a Test Method

    E2586 Practice for Calculating and Using Basic Statistics

    E2587 Practice for Use of Control Charts in Statistical Process Control