ASTM E1137 / E1137M - 08(2014) Standard Specification for Industrial Platinum Resistance Thermometers


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    D5/D5M Standard Test Method for Penetration of Bituminous Materials

    D402/D402M Standard Test Method for Distillation of Cutback Asphalt

    D445 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)

    D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position

    D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact

    D1525 Standard Test Method for Vicat Softening Temperature of Plastics

    D1754/D1754M Standard Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)

    D2162 Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards

    D2726/D2726M Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures

    D2872 Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test)

    D3012 Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven

    D3143/D3143M Standard Test Method for Flash Point of Cutback Asphalt with Tag Open-Cup Apparatus

    D3195/D3195M Standard Practice for Rotameter Calibration

    D3791/D3791M Standard Practice for Evaluating the Effects of Heat on Asphalts

    D3828 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester

    D3829 Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil

    D4402/D4402M Standard Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer

    D4684 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature

    D5298 Standard Test Method for Measurement of Soil Potential (Suction) Using Filter Paper

    D5438 Standard Practice for Collection of Floor Dust for Chemical Analysis

    D5801 Standard Test Method for Toughness and Tenacity of Bituminous Materials

    D5869 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials

    D6084/D6084M Standard Test Method for Elastic Recovery of Bituminous Materials by Ductilometer

    D6176 Standard Practice for Measuring Surface Atmospheric Temperature with Electrical Resistance Temperature Sensors

    D6521 Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV)

    D6821 Standard Test Method for Low Temperature Viscosity of Drive Line Lubricants in a Constant Shear Stress Viscometer

    D6896 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature

    E344 Terminology Relating to Thermometry and Hydrometry

    E644 Standard Test Methods for Testing Industrial Resistance Thermometers

    E1652 Standard Specification for Magnesium Oxide and Aluminum Oxide Powder and Crushable Insulators Used in the Manufacture of Base Metal Thermocouples, Metal-Sheathed Platinum Resistance Thermometers, and Noble Metal Thermocouples

    E2593 Standard Guide for Accuracy Verification of Industrial Platinum Resistance Thermometers

    E2821 Standard Specification for ?Compacted Mineral-Insulated, Metal-Sheathed Cable Used in Industrial Resistance Thermometers

    E2877 Standard Guide for Digital Contact Thermometers


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service

    B167 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674) Seamless Pipe and Tube

    E344 Terminology Relating to Thermometry and Hydrometry

    E644 Test Methods for Testing Industrial Resistance Thermometers

    E1652 Specification for Magnesium Oxide and Aluminum Oxide Powder and Crushable Insulators Used in the Manufacture of Base Metal Thermocouples, Metal-Sheathed Platinum Resistance Thermometers, and Noble Metal Thermocouples