ASTM D95 - 05(2010) Standard Test Method for Water in Petroleum Products and Bituminous Materials by DistillationCiting ASTM Standards
Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.
D128 Standard Test Methods for Analysis of Lubricating Grease D228/D228M Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing D396 Standard Specification for Fuel Oils D490 Standard Specification for Road Tar D1208 Standard Test Methods for Common Properties of Certain Pigments D1796 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) D2026/D2026M Standard Specification for Cutback Asphalt (Slow-Curing Type) D2027/D2027M Standard Specification for Cutback Asphalt (Medium-Curing Type) D2028/D2028M Standard Specification for Cutback Asphalt (Rapid-Curing Type) D2318 Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch D2523 Standard Practice for Testing Load-Strain Properties of Roofing Membranes D2982 Standard Test Methods for Detecting Glycol-Base Antifreeze in Used Lubricating Oils D3326 Standard Practice for Preparation of Samples for Identification of Waterborne Oils D3381/D3381M Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction D3712 Standard Test Method of Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography D4006 Standard Test Method for Water in Crude Oil by Distillation D4007 Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure) D4072 Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch D4073 Standard Test Method for Tensile-Tear Strength of Bituminuous Roofing Membranes D4312 Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch (Short Method) D4746 Standard Test Method for Determination of Quinoline Insolubles (QI) in Tar and Pitch by Pressure Filtration D4868 Standard Test Method for Estimation of Net and Gross Heat of Combustion of Burner and Diesel Fuels D5147/D5147M Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material D5372 Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids D5727/D5727M Standard Specification for Emulsified Refined Coal Tar (Mineral Colloid Type) D6224 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment D6373 Standard Specification for Performance Graded Asphalt Binder D6448 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils D6511/D6511M Standard Test Methods for Solvent Bearing Bituminous Compounds D6626 Standard Specification for Performance Graded Trinidad Lake Modified Asphalt Binder D6630 Standard Guide for Low Slope Insulated Roof Membrane Assembly Performance D6666 Standard Guide for Evaluation of Aqueous Polymer Quenchants D6710 Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil D6813 Standard Guide for Performance Evaluation of Hydraulic Fluids for Piston Pumps D6823 Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils D7044 Standard Specification for Biodegradable Fire Resistant Hydraulic Fluids D7280 Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch by Stainless Steel Crucible Filtration D7665 Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids E123 Standard Specification for Apparatus for Determination of Water by Distillation E1417/E1417M Standard Practice for Liquid Penetrant Testing F601 Standard Practice for Fluorescent Penetrant Inspection of Metallic Surgical Implants Referenced ASTM Standards
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
| ||