ASTM D93 - 13e1 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    C461 Standard Test Methods for Mastics and Coatings Used With Thermal Insulation

    C647 Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation

    C916 Standard Specification for Adhesives for Duct Thermal Insulation

    D56 Standard Test Method for Flash Point by Tag Closed Cup Tester

    D88 Standard Test Method for Saybolt Viscosity

    D92 Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester

    D115 Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation

    D154 Standard Guide for Testing Varnishes

    D268 Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material

    D333 Standard Guide for Clear and Pigmented Lacquers

    D396 Standard Specification for Fuel Oils

    D803 Standard Test Methods for Testing Tall Oil

    D910 Standard Specification for Leaded Aviation Gasolines

    D975 Standard Specification for Diesel Fuel Oils

    D1655 Standard Specification for Aviation Turbine Fuels

    D2880 Standard Specification for Gas Turbine Fuel Oils

    D3278 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus

    D3730 Standard Guide for Testing High-Performance Interior Architectural Wall Coatings

    D3757 Standard Guide for Preparing Specifications for Solvent-based Floor Polishes

    D3934 Standard Test Method for Flash/No Flash Test-Equilibrium Method by a Closed-Cup Apparatus

    D3941 Standard Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus

    D3955 Standard Specification for Electrical Insulating Varnishes

    D4171 Standard Specification for Fuel System Icing Inhibitors

    D4485 Standard Specification for Performance of Active API Service Category Engine Oils

    D4625 Standard Test Method for Distillate Fuel Storage Stability at 43°C (110°F)

    D4733 Standard Test Methods for Solventless Electrical Insulating Varnishes

    D4857 Standard Test Method for Determination of the Ability of Lubricants to Minimize Ring Sticking and Piston Deposits in Two-Stroke-Cycle Gasoline Engines Other Than Outboards

    D4865 Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems

    D5146 Standard Guide to Testing Solvent-Borne Architectural Coatings

    D5372 Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids

    D5452 Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration

    D5966 Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine

    D5967 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

    D6217 Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration

    D6361/D6361M Standard Guide for Selecting Cleaning Agents and Processes

    D6448 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils

    D6468 Standard Test Method for High Temperature Stability of Middle Distillate Fuels

    D6577 Standard Guide for Testing Industrial Protective Coatings

    D6618 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine

    D6681 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure

    D6750 Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure(0.4 % Fuel Sulfur) and 1N Procedure(0.04 % Fuel Sulfur)

    D6751 Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels

    D6763 Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents

    D6813 Standard Guide for Performance Evaluation of Hydraulic Fluids for Piston Pumps

    D6823 Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils

    D6894 Standard Test Method for Evaluation of Aeration Resistance of Engine Oils in Direct-Injected Turbocharged Automotive Diesel Engine

    D6923 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure

    D6987/D6987M Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine

    D7094 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester

    D7156 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine

    D7215 Standard Test Method for Calculated Flash Point from Simulated Distillation Analysis of Distillate Fuels

    D7422 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine

    D7467 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)

    D7468 Standard Test Method for Cummins ISM Test

    D7484 Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine

    D7544 Standard Specification for Pyrolysis Liquid Biofuel

    D7549 Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure

    D7566 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons

    D7583 Standard Test Method for John Deere Coolant Cavitation Test

    D7665 Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids

    D7666 Standard Specification for Triglyceride Burner Fuel

    E502 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods

    E709 Standard Guide for Magnetic Particle Testing

    F715 Standard Test Methods for Coated Fabrics Used for Oil Spill Control and Storage

    F718 Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet

    F1200 Standard Specification for Fabricated (Welded) Pipe Line Strainers (Above 150 psig and 150°F)

    F1201 Standard Specification for Fluid Conditioner Fittings in Piping Applications Above 0°F

    F2417 Standard Specification for Fire Safety for Candles

    F2701 Standard Test Method for Evaluating Heat Transfer through Materials for Protective Clothing Upon Contact with a Hot Liquid Splash


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    D56 Test Method for Flash Point by Tag Closed Cup Tester

    D3941 Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus

    D4057 Practice for Manual Sampling of Petroleum and Petroleum Products

    D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products

    E1 Specification for ASTM Liquid-in-Glass Thermometers

    E300 Practice for Sampling Industrial Chemicals

    E502 Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods