ASTM D8 - 13b Standard Terminology Relating to Materials for Roads and Pavements


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    C1097 Standard Specification for Hydrated Lime for Use in Asphalt Cement or Bituminous Paving Mixtures

    D75/D75M Standard Practice for Sampling Aggregates

    D448 Standard Classification for Sizes of Aggregate for Road and Bridge Construction

    D692/D692M Standard Specification for Coarse Aggregate for Bituminous Paving Mixtures

    D1073 Standard Specification for Fine Aggregate for Bituminous Paving Mixtures

    D1139/D1139M Standard Specification for Aggregate for Single or Multiple Bituminous Surface Treatments

    D2205 Standard Guide for Selection of Tests for Traffic Paints

    D2321 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

    D2419 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate

    D2489/D2489M Standard Practice for Estimating Degree of Particle Coating of Bituminous-Aggregate Mixtures

    D2728 Standard Practice for Paving Uses and Application Temperatures for Road Tars

    D3628 Standard Practice for Selection and Use of Emulsified Asphalts

    D3666 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials

    D3839 Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe

    D4215 Standard Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures

    D4223/D4223M Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils

    D5106 Standard Specification for Steel Slag Aggregates for Bituminous Paving Mixtures

    D5821 Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate

    D6088 Standard Practice for Installation of Geocomposite Pavement Drains

    D6155 Standard Specification for Nontraditional Coarse Aggregates for Bituminous Paving Mixtures

    D6373 Standard Specification for Performance Graded Asphalt Binder

    D6521 Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV)

    D6626 Standard Specification for Performance Graded Trinidad Lake Modified Asphalt Binder

    D6704 Standard Test Method for Determining the Workability of Asphalt Cold Mix Patching Material

    D6723 Standard Test Method for Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT)

    D6816 Standard Practice for Determining Low-Temperature Performance Grade (PG) of Asphalt Binders

    D7000 Standard Test Method for Sweep Test of Bituminous Emulsion Surface Treatment Samples

    D7172 Standard Test Method for Determining the Relative Density (Specific Gravity) and Absorption of Fine Aggregates Using Infrared

    D7229 Standard Test Method for Preparation and Determination of the Bulk Specific Gravity of Dense-Graded Cold Mix Asphalt (CMA) Specimens by Means of the Superpave Gyratory Compactor

    D7313 Standard Test Method for Determining Fracture Energy of Asphalt-Aggregate Mixtures Using the Disk-Shaped Compact Tension Geometry

    D7405 Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer

    D7643 Standard Practice for Determining the Continuous Grading Temperatures and Continuous Grades for PG Graded Asphalt Binders

    E867 Standard Terminology Relating to Vehicle-Pavement Systems

    F1668 Standard Guide for Construction Procedures for Buried Plastic Pipe


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    D4124 Test Method for Separation of Asphalt into Four Fractions

    D4552 Practice for Classifying Hot-Mix Recycling Agents

    D5505 Practice for Classifying Emulsified Recycling Agents