ASTM D4253 - 00(2006) Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    C361M Standard Specification for Reinforced Concrete Low-Head Pressure Pipe (Metric)

    C361 Standard Specification for Reinforced Concrete Low-Head Pressure Pipe

    D653 Standard Terminology Relating to Soil, Rock, and Contained Fluids

    D698 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft3 (600 kN-m/m3))

    D1556 Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method

    D1557 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3))

    D2167 Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method

    D2434 Standard Test Method for Permeability of Granular Soils (Constant Head)

    D3839 Standard Guide for Underground Installation of “Fiberglass” (Glass-FiberReinforced Thermosetting-Resin) Pipe

    D4254 Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density

    D4718 Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles

    D4874 Standard Test Method for Leaching Solid Material in a Column Apparatus

    D4914 Standard Test Methods for Density and Unit Weight of Soil and Rock in Place by the Sand Replacement Method in a Test Pit

    D5030/D5030M Standard Test Methods for Density of Soil and Rock in Place by the Water Replacement Method in a Test Pit

    D5311/D5311M Standard Test Method for Load Controlled Cyclic Triaxial Strength of Soil

    D6270 Standard Practice for Use of Scrap Tires in Civil Engineering Applications

    D6938 Standard Test Method for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)

    D7382 Standard Test Methods for Determination of Maximum Dry Unit Weight and Water Content Range for Effective Compaction of Granular Soils Using a Vibrating Hammer

    D7698 Standard Test Method for In-Place Estimation of Density and Water Content of Soil and Aggregate by Correlation with Complex Impedance Method

    D7830/D7830M Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge

    E2243 Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Re-contouring and Highwall Reclamation

    E2277 Standard Guide for Design and Construction of Coal Ash Structural Fills

    E2278 Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage

    F1668 Standard Guide for Construction Procedures for Buried Plastic Pipe


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    C127 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate

    D422 Test Method for Particle-Size Analysis of Soils

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D698 Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft3 (600 kN-m/m3))

    D854 Test Methods for Specific Gravity of Soil Solids by Water Pycnometer

    D1140 Test Methods for Amount of Material in Soils Finer than No. 200 (75-m) Sieve

    D1557 Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3))

    D2216 Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

    D2487 Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)

    D2488 Practice for Description and Identification of Soils (Visual-Manual Procedure)

    D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction

    D4254 Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density

    D4753 Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing

    D6026 Practice for Using Significant Digits in Geotechnical Data

    E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves

    E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method