ASTM D3892 - 93(2009) Standard Practice for Packaging/Packing of Plastics


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    C149 Standard Test Method for Thermal Shock Resistance of Glass Containers

    D704 Standard Specification for Melamine-Formaldehyde Molding Compounds

    D705 Standard Specification for Urea-Formaldehyde Molding Compounds

    D706 Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds

    D707 Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds

    D787 Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds

    D788 Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds

    D1201 Standard Specification for Thermosetting Polyester Molding Compounds

    D1248 Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

    D1430 Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics

    D1562 Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds

    D1593 Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting

    D1636 Standard Specification for Allyl Molding Compounds

    D1710 Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes

    D1755 Standard Specification for Poly(Vinyl Chloride) Resins

    D1763 Standard Specification for Epoxy Resins

    D1784 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

    D1998 Standard Specification for Polyethylene Upright Storage Tanks

    D2103 Standard Specification for Polyethylene Film and Sheeting

    D2116 Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials

    D2287 Standard Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds

    D2517 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings

    D2581 Standard Specification for Polybutylene (PB) Plastics Molding and Extrusion Materials

    D2647 Standard Specification for Crosslinkable Ethylene Plastics

    D2673 Standard Specification for Oriented Polypropylene Film

    D3013 Standard Specification for Epoxy Molding Compounds

    D3159 Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials

    D3222 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials

    D3262 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe

    D3275 Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials

    D3294 Standard Specification for PTFE Resin Molded Sheet and Molded Basic Shapes

    D3295 Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing

    D3299 Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

    D3307 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials

    D3308 Standard Specification for PTFE Resin Skived Tape

    D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials

    D3368 Standard Specification for FEP-Fluorocarbon Sheet and Film

    D3517 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe

    D3595 Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and Film

    D3678 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions

    D3679 Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding

    D3753 Standard Specification for Glass-Fiber-Reinforced Polyester Manholes and Wetwells

    D3754 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe

    D3840 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications

    D3841 Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels

    D3935 Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material

    D3965 Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings

    D4000 Standard Classification System for Specifying Plastic Materials

    D4066 Standard Classification System for Nylon Injection and Extrusion Materials (PA)

    D4067 Standard Classification System for and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods

    D4097 Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

    D4101 Standard Specification for Polypropylene Injection and Extrusion Materials

    D4203 Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials

    D4349 Classification System and Basis for Specification for Polyphenylene Ether (PPE) Materials

    D4396 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications

    D4397 Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications

    D4441 Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene

    D4477 Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit

    D4549 Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS)

    D4551 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane

    D4634 Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)

    D4673 Standard Classification System for Acrylonitrile-Butadiene-Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials

    D4726 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used for Assembled Windows and Doors

    D4745 Standard Specification for Filled Compounds of Polytetrafluoroethylene (PTFE) Molding and Extrusion Materials

    D4801 Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm [0.010 in.] and Greater

    D4802 Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet

    D4894 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials

    D4895 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion

    D4969 Standard Specification for Polytetrafluoroethylene–(PTFE) Coated Glass Fabric

    D4976 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials

    D5047 Standard Specification for Polyethylene Terephthalate Film and Sheeting

    D5138 Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP)

    D5203 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources

    D5204 Standard Classification System for Polyamide-Imide (PAI) Molding and Extrusion Materials

    D5205 Standard Classification System for Polyetherimide (PEI) Materials

    D5336 Standard Specification for Polyphthalamide (PPA) Injection Molding Materials

    D5436 Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes

    D5575 Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers

    D5675 Standard Classification for Low Molecular Weight PTFE and FEP Micronized Powders

    D5740 Standard Guide for Writing Material Standards in the Classification D4000 Format

    D5857 Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology

    D5926 Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems

    D5927 Standard Classification System for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods

    D5989 Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA)

    D6098 Standard Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC)

    D6100 Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM)

    D6261 Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)

    D6262 Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)

    D6263 Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC)

    D6338 Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPVs) Based on ASTM Standard Test Methods

    D6339 Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)

    D6358 Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ISO Methods

    D6394 Standard Specification for Sulfone Plastics (SP)

    D6456 Standard Specification for Finished Parts Made from Polyimide Resin

    D6457 Standard Specification for Extruded and Compression Molded Rod and Heavy-Walled Tubing Made from Polytetrafluoroethylene (PTFE)

    D6585 Standard Specification for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape

    D6712 Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes

    D6713 Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF)

    D6778 Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM)

    D6779 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)

    D6783 Standard Specification for Polymer Concrete Pipe

    D6835 Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE)

    D6865 Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM&

    D7193 Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape

    D7254 Standard Specification for Polypropylene (PP) Siding

    D7292 Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI)

    D7293 Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI)

    D7436 Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology

    D7445 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)

    D7471 Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials

    D7472 Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials

    D7793 Standard Specification for Insulated Vinyl Siding

    F997 Standard Specification for Polycarbonate Resin for Medical Applications

    F2207 Standard Specification for Cured-in-Place Pipe Lining System for Rehabilitation of Metallic Gas Pipe

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    D883 Terminology Relating to Plastics