ASTM D36 / D36M - 14e1 Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A849 Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe

    C647 Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation

    C877M Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections (Metric)

    C877 Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections

    C990M Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)

    C990 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants

    D5/D5M Standard Test Method for Penetration of Bituminous Materials

    D312 Standard Specification for Asphalt Used in Roofing

    D449/D449M Standard Specification for Asphalt Used in Dampproofing and Waterproofing

    D450/D450M Standard Specification for Coal-Tar Pitch Used in Roofing, Dampproofing, and Waterproofing

    D490 Standard Specification for Road Tar

    D946/D946M Standard Specification for Penetration-Graded Asphalt Cement for Use in Pavement Construction

    D2746 Standard Test Method for Staining Tendency of Asphalt (Stain Index)

    D3019 Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, Asbestos-Fibered, and Non-Asbestos-Fibered

    D3141/D3141M Standard Specification for Asphalt for Undersealing Portland-Cement Concrete Pavements

    D3381/D3381M Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction

    D3461 Standard Test Method for Softening Point of Asphalt and Pitch (Mettler Cup-and-Ball Method)

    D3462/D3462M Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules

    D3666 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials

    D3745 Standard Practice for Installation of Prefabricated Asphalt Reservoir, Pond, Canal, and Ditch Liner (Exposed Type)

    D3791/D3791M Standard Practice for Evaluating the Effects of Heat on Asphalts

    D4280 Standard Specification for Extended Life Type, Nonplowable, Raised Retroreflective Pavement Markers

    D4383 Standard Specification for Plowable, Raised Retroreflective Pavement Markers

    D4799/D4799M Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV, Water Spray, and Condensation Method)

    D5078/D5078M Standard Specification for Crack Filler, Hot-Applied, for Asphalt Concrete and Portland Cement Concrete Pavements

    D5546 Standard Test Method for Solubility of Asphalt Binders in Toluene by Centrifuge

    D6114/D6114M Standard Specification for Asphalt-Rubber Binder

    D6152/D6152M Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing

    D6154 Standard Specification for Chemically Modified Asphalt Cement for Use in Pavement Construction

    D6297 Standard Specification for Asphaltic Plug Joints for Bridges

    D6455 Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGM)

    D6493 Standard Test Methods for Softening Point of Hydrocarbon Resins and Rosin Based Resins by Automated Ring-and-Ball Apparatus

    D6690 Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements

    D7173 Standard Practice for Determining the Separation Tendency of Polymer from Polymer Modified Asphalt

    E28 Standard Test Methods for Softening Point of Resins Derived from Pine Chemicals and Hydrocarbons, by Ring-and-Ball Apparatus


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    C670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials

    D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester

    D140 Practice for Sampling Bituminous Materials

    D3461 Test Method for Softening Point of Asphalt and Pitch (Mettler Cup-and-Ball Method)

    E1 Specification for ASTM Liquid-in-Glass Thermometers

    E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method