D1248 Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

D1693 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics

D2239 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

D2513 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

D2683 Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing

D2737 Standard Specification for Polyethylene (PE) Plastic Tubing

D3035 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

D3261 Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

D4000 Standard Classification System for Specifying Plastic Materials

D4703 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

D4883 Standard Test Method for Density of Polyethylene by the Ultrasound Technique

D4976 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials

D7001 Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications

E1858 Standard Test Method for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry

E1860 Standard Test Method for Elapsed Time Calibration Thermal Analyzers

E2009 Standard Test Method for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry

E2046 Standard Test Method for Reaction Induction Time by Thermal Analysis

F412 Standard Terminology Relating to Plastic Piping Systems

F585 Standard Practice for Insertion of Flexible Polyethylene Pipe Into Existing Sewers

F645 Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

F667 Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings

F714 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter

F771 Standard Specification for Polyethylene (PE) Thermoplastic High-Pressure Irrigation Pipeline Systems

F810 Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields

F894 Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe

F1055 Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing

F1056 Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings

F1281 Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe

F1282 Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

F1412 Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems

F1533 Standard Specification for Deformed Polyethylene (PE) Liner

F1606 Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner

F1734 Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe

F1759 Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications

F1901 Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems

F1970 Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems

F1986 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems

F1987 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems

F2021 Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems

F2160 Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD)

F2262 Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Tubing OD Controlled SDR9

F2306/F2306M Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications

F2435 Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe

F2562/F2562M Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage

F2619/F2619M Standard Specification for High-Density Polyethylene (PE) Line Pipe

F2623 Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 Tubing

F2648/F2648M Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

F2649 Standard Specification for Corrugated High Density Polyethylene (HDPE) Grease Interceptor Tanks

F2686 Standard Specification for Glass Fiber Reinforced Thermoplastic Pipe

F2720/F2720M Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe

F2737 Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units

F2762 Standard Specification for 12 to 30 in. [300 to 750 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

F2763 Standard Specification for 30 to 60 in. [750 to 1500 mm] Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

F2769 Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems

F2818 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing

F2880 Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes ¾ in. to 65 in.