ASTM D2581 - 09 Standard Specification for Polybutylene (PB) Plastics Molding and Extrusion Materials


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    There are currently no referencing documents for this standard.


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

    D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies

    D150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation

    D257 Test Methods for DC Resistance or Conductance of Insulating Materials

    D495 Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation

    D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents

    D570 Test Method for Water Absorption of Plastics

    D618 Practice for Conditioning Plastics for Testing

    D635 Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

    D638 Test Method for Tensile Properties of Plastics

    D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position

    D696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30C and 30C with a Vitreous Silica Dilatometer

    D732 Test Method for Shear Strength of Plastics by Punch Tool

    D746 Test Method for Brittleness Temperature of Plastics and Elastomers by Impact

    D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

    D883 Terminology Relating to Plastics

    D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer

    D1505 Test Method for Density of Plastics by the Density-Gradient Technique

    D1525 Test Method for Vicat Softening Temperature of Plastics

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D1603 Test Method for Carbon Black Content in Olefin Plastics

    D2240 Test Method for Rubber Property--Durometer Hardness

    D2863 Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)

    D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics

    D3418 Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry

    D3801 Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position

    D3892 Practice for Packaging/Packing of Plastics

    D3895 Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry

    D4000 Classification System for Specifying Plastic Materials

    D4703 Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

    D5033 Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics

    D5279 Test Method for Plastics: Dynamic Mechanical Properties: In Torsion

    D5630 Test Method for Ash Content in Plastics

    D6110 Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics

    D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E105 Practice for Probability Sampling of Materials

    E831 Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis

    F699 Practice for Accelerated Conditioning of Polybutylene Pipe and Tubing for Subsequent Quality Control Testing