ASTM D217 - 10 Standard Test Methods for Cone Penetration of Lubricating Grease


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    C461 Standard Test Methods for Mastics and Coatings Used With Thermal Insulation

    C782 Standard Test Method for Softness of Preformed Tape Sealants

    C877M Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections (Metric)

    C877 Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections

    C990M Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)

    C990 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants

    C1125 Standard Test Method for Penetration Index of Asbestos

    D128 Standard Test Methods for Analysis of Lubricating Grease

    D566 Standard Test Method for Dropping Point of Lubricating Grease

    D937 Standard Test Method for Cone Penetration of Petrolatum

    D972 Standard Test Method for Evaporation Loss of Lubricating Greases and Oils

    D1092 Standard Test Method for Measuring Apparent Viscosity of Lubricating Greases

    D1321 Standard Test Method for Needle Penetration of Petroleum Waxes

    D1403 Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment

    D1831 Standard Test Method for Roll Stability of Lubricating Grease

    D2265 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range

    D2595 Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range

    D3757 Standard Guide for Preparing Specifications for Solvent-based Floor Polishes

    D4049 Standard Test Method for Determining the Resistance of Lubricating Grease to Water Spray

    D4057 Standard Practice for Manual Sampling of Petroleum and Petroleum Products

    D4289 Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids

    D4425 Standard Test Method for Oil Separation From Lubricating Grease by Centrifuging (Koppers Method)

    D4693 Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings

    D4732 Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable

    D4950 Standard Classification and Specification for Automotive Service Greases

    D5078/D5078M Standard Specification for Crack Filler, Hot-Applied, for Asphalt Concrete and Portland Cement Concrete Pavements

    D5329 Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphaltic and Portland Cement Concrete Pavements

    D5706 Standard Test Method for Determining Extreme Pressure Properties of Lubricating Greases Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D5707 Standard Test Method for Measuring Friction and Wear Properties of Lubricating Grease Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D6138 Standard Test Method for Determination of Corrosion-Preventive Properties of Lubricating Greases Under Dynamic Wet Conditions (Emcor Test)

    D6184 Standard Test Method for Oil Separation from Lubricating Grease (Conical Sieve Method)

    D6185 Standard Practice for Evaluating Compatibility of Binary Mixtures of Lubricating Greases

    D6297 Standard Specification for Asphaltic Plug Joints for Bridges

    D7342 Standard Test Method for Shear Stability of Lubricating Grease in Presence of Water (Water Stability Test)

    D7420 Standard Test Method for Determining Tribomechanical Properties of Grease Lubricated Plastic Socket Suspension Joints Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7594 Standard Test Method for Determining Fretting Wear Resistance of Lubricating Greases Under High Hertzian Contact Pressures Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7718 Standard Practice for Obtaining In-Service Samples of Lubricating Grease

    F2489 Standard Guide for Instrument and Precision Bearing Lubricants—Part 2 Greases

    G63 Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    D937 Test Method for Cone Penetration of Petrolatum

    D1403 Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment