ASTM D1693 - 13 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    C149 Standard Test Method for Thermal Shock Resistance of Glass Containers

    D1248 Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

    D1998 Standard Specification for Polyethylene Upright Storage Tanks

    D2308 Standard Specification for Thermoplastic Polyethylene Jacket for Electrical Wire and Cable

    D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials

    D3554 Standard Specification for Track-Resistant Black Thermoplastic High-Density Polyethylene Insulation for Wire and Cable, 75 °C Operation

    D4000 Standard Classification System for Specifying Plastic Materials

    D4565 Standard Test Methods for Physical and Environmental Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable

    D4740 Standard Test Method for Cleanliness and Compatibility of Residual Fuels by Spot Test

    D4976 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials

    D6973 Standard Test Method for Indicating Wear Characteristics of Petroleum Hydraulic Fluids in a High Pressure Constant Volume Vane Pump

    D7082 Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe

    D7095 Standard Test Method for Rapid Determination of Corrosiveness to Copper from Petroleum Products Using a Disposable Copper Foil Strip

    D7436 Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology

    F810 Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields

    F1533 Standard Specification for Deformed Polyethylene (PE) Liner

    F2160 Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD)

    F2718 Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines

    F2896 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes

    F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    D618 Practice for Conditioning Plastics for Testing

    D883 Terminology Relating to Plastics

    D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature

    D1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

    D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials

    D4703 Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

    D4976 Specification for Polyethylene Plastics Molding and Extrusion Materials

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method