ASTM C270 - 12a Standard Specification for Mortar for Unit Masonry


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    C51 Standard Terminology Relating to Lime and Limestone (as used by the Industry)

    C91/C91M Standard Specification for Masonry Cement

    C141/C141M Standard Specification for Hydrated Hydraulic Lime for Structural Purposes

    C144 Standard Specification for Aggregate for Masonry Mortar

    C387/C387M Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar

    C780 Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry

    C901 Standard Specification for Prefabricated Masonry Panels

    C946 Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls

    C952 Standard Test Method for Bond Strength of Mortar to Masonry Units

    C1072 Standard Test Methods for Measurement of Masonry Flexural Bond Strength

    C1093 Standard Practice for Accreditation of Testing Agencies for Masonry

    C1142 Standard Specification for Extended Life Mortar for Unit Masonry

    C1148 Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar

    C1180 Standard Terminology of Mortar and Grout for Unit Masonry

    C1283 Standard Practice for Installing Clay Flue Lining

    C1314 Standard Test Method for Compressive Strength of Masonry Prisms

    C1324 Standard Test Method for Examination and Analysis of Hardened Masonry Mortar

    C1357 Standard Test Methods for Evaluating Masonry Bond Strength

    C1384 Standard Specification for Admixtures for Masonry Mortars

    C1400 Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls

    C1403 Standard Test Method for Rate of Water Absorption of Masonry Mortars

    C1586 Standard Guide for Quality Assurance of Mortars

    C1692 Standard Practice for Construction and Testing of Autoclaved Aerated Concrete (AAC) Masonry

    C1707 Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes

    C1713 Standard Specification for Mortars for the Repair of Historic Masonry

    C1714/C1714M Standard Specification for Preblended Dry Mortar Mix for Unit Masonry

    C1722 Standard Guide for Repair and Restoration of Dimension Stone

    C1780 Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer

    C1791 Standard Guide for Reduction of Efflorescence Potential in New Unit Pavement Systems

    E514/E514M Standard Test Method for Water Penetration and Leakage Through Masonry

    E518/E518M Standard Test Methods for Flexural Bond Strength of Masonry

    E754 Standard Test Method for Pullout Resistance of Ties and Anchors Embedded in Masonry Mortar Joints

    E1602 Standard Guide for Construction of Solid Fuel Burning Masonry Heaters

    E2260 Standard Guide for Repointing (Tuckpointing) Historic Masonry

    E2266 Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    C5 Specification for Quicklime for Structural Purposes

    C91 Specification for Masonry Cement

    C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)

    C110 Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

    C128 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate

    C144 Specification for Aggregate for Masonry Mortar

    C150 Specification for Portland Cement

    C188 Test Method for Density of Hydraulic Cement

    C207 Specification for Hydrated Lime for Masonry Purposes

    C305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency

    C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes

    C595 Specification for Blended Hydraulic Cements

    C780 Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry

    C952 Test Method for Bond Strength of Mortar to Masonry Units

    C979 Specification for Pigments for Integrally Colored Concrete

    C1072 Test Methods for Measurement of Masonry Flexural Bond Strength

    C1093 Practice for Accreditation of Testing Agencies for Masonry

    C1157 Performance Specification for Hydraulic Cement

    C1180 Terminology of Mortar and Grout for Unit Masonry

    C1232 Terminology of Masonry

    C1324 Test Method for Examination and Analysis of Hardened Masonry Mortar

    C1329 Specification for Mortar Cement

    C1384 Specification for Admixtures for Masonry Mortars

    C1489 Specification for Lime Putty for Structural Purposes

    C1506 Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters

    C1586 Guide for Quality Assurance of Mortars

    E72 Test Methods of Conducting Strength Tests of Panels for Building Construction

    E514 Test Method for Water Penetration and Leakage Through Masonry

    E518 Test Methods for Flexural Bond Strength of Masonry