ASTM B16 / B16M - 10 Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    B249/B249M Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

    B250/B250M Standard Specification for General Requirements for Wrought Copper Alloy Wire

    B453/B453M Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes

    B927/B927M Standard Specification for Brass Rod, Bar, and Shapes

    D897 Standard Test Method for Tensile Properties of Adhesive Bonds

    D950 Standard Test Method for Impact Strength of Adhesive Bonds

    D1062 Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds

    D2625 Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method)

    D2670 Standard Test Method for Measuring Wear Properties of Fluid Lubricants (Falex Pin and Vee Block Method)

    D3233 Standard Test Methods for Measurement of Extreme Pressure Properties of Fluid Lubricants (Falex Pin and Vee Block Methods)

    F721 Standard Specification for Gage Piping Assemblies

    F826 Standard Specification for Tops, Furniture, Marine, Steel

    F1387 Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings

    F1433 Standard Specification for Mechanically Refrigerated Shipboard Air Conditioner

    F1807 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

    F1865 Standard Specification for Mechanical Cold Expansion Insert Fitting With Compression Sleeve for Cross-linked Polyethylene (PEX) Tubing

    F1960 Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing

    F1961 Standard Specification for Metal Mechanical Cold Flare Compression Fittings with Disc Spring for Crosslinked Polyethylene (PEX) Tubing

    F1974 Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe

    F2080 Standard Specification for Cold-Expansion Fittings With Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe

    F2434 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing

    F2854 Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing

    F2929 Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

    B250/B250M Specification for General Requirements for Wrought Copper Alloy Wire

    B601 Classification for Temper Designations for Copper and Copper Alloys--Wrought and Cast

    E8 Test Methods for Tension Testing of Metallic Materials

    E8M Test Methods for Tension Testing of Metallic Materials [Metric]

    E18 Test Methods for Rockwell Hardness of Metallic Materials

    E478 Test Methods for Chemical Analysis of Copper Alloys