ASTM A653 / A653M - 13 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A90/A90M Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings

    A754/A754M Standard Test Method for Coating Weight (Mass) of Metallic Coatings on Steel by X-Ray Fluorescence

    A755/A755M Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products

    A787/A787M Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing

    A924/A924M Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process

    A1003/A1003M Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members

    A1076/A1076M Standard Specification for Cold Formed Carbon Structural Steel Tubing Made from Metallic Precoated Sheet Steel

    C645 Standard Specification for Nonstructural Steel Framing Members

    C754 Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products

    C847 Standard Specification for Metal Lath

    C921 Standard Practice for Determining the Properties of Jacketing Materials for Thermal Insulation

    C955 Standard Specification for Load-Bearing (Transverse and Axial) Steel Studs, Runners (Tracks), and Bracing or Bridging for Screw Application of Gypsum Panel Products and Metal Plaster Bases

    C956 Standard Specification for Installation of Cast-In-Place Reinforced Gypsum Concrete

    C1047 Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

    C1063 Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster

    C1696 Standard Guide for Industrial Thermal Insulation Systems

    D5933 Standard Specification for 2 5/8-in. and 4-in. Diameter Metal Shear Plates for Use in Wood Constructions

    E1514 Standard Specification for Structural Standing Seam Steel Roof Panel Systems

    F683 Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery

    F825 Standard Specification for Drawers, Furniture, Marine, Steel

    F1178 Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture

    F1697 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit

    F2408 Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets

    F2435 Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for

    A902 Terminology Relating to Metallic Coated Steel Products

    A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process

    D7396 Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting

    E517 Test Method for Plastic Strain Ratio r for Sheet Metal

    E646 Test Method for Tensile Strain-Hardening Exponents (n -Values) of Metallic Sheet Materials