ASTM A563 - 07a(2014) Standard Specification for Carbon and Alloy Steel Nuts


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A36/A36M Standard Specification for Carbon Structural Steel

    A307 Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60000 PSI Tensile Strength

    A325 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A385/A385M Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip)

    A394 Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare

    A449 Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

    A490 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    A760/A760M Standard Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains

    A761/A761M Standard Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches

    A762/A762M Standard Specification for Corrugated Steel Pipe, Polymer Precoated for Sewers and Drains

    A978/A978M Standard Specification for Composite Ribbed Steel Pipe, Precoated and Polyethylene Lined for Gravity Flow Sanitary Sewers, Storm Sewers, and Other Special Applications

    A1042/A1042M Standard Specification for Composite Corrugated Steel Pipe for Sewers and Drains

    B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    B745/B745M Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

    B746/B746M Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches

    B864/B864M Standard Specification for Corrugated Aluminum Box Culverts

    F432 Standard Specification for Roof and Rock Bolts and Accessories

    F1018 Standard Specification for Steel Emergency Gear Stowage Locker

    F1073 Standard Specification for Door Fittings, for Watertight /Gastight /Airtight, Weathertight, and Non-Tight Doors, for Marine Use

    F1155 Standard Practice for Selection and Application of Piping System Materials

    F1476 Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications

    F1510 Standard Specification for Rotary Positive Displacement Pumps, Ships Use

    F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength

    F1718 Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

    F1789 Standard Terminology for F16 Mechanical Fasteners

    F1852 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    F2329 Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners

    F2363/F2363M Standard Specification for Sewage and Graywater Flow Through Treatment Systems

    F2437 Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs

    F2798 Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    A194/A194M Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both

    A242/A242M Specification for High-Strength Low-Alloy Structural Steel

    A307 Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength

    A325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    A354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A394 Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare

    A449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

    A490 Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    A588/A588M Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance

    A687 Specification for High-Strength Nonheaded Steel Belts and Studs Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.

    A709/A709M Specification for Structural Steel for Bridges

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    D3951 Practice for Commercial Packaging

    F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F812/F812M Specification for Surface Discontinuities of Nuts, Inch and Metric Series

    F1789 Terminology for F16 Mechanical Fasteners

    F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners

    G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels