ASTM A490 - 12 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A325 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A490M Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)

    A563 Standard Specification for Carbon and Alloy Steel Nuts

    B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    C1533 Standard Guide for General Design Considerations for Hot Cell Equipment

    F436 Standard Specification for Hardened Steel Washers

    F959 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners

    F1624 Standard Test Method for Measurement of Hydrogen Embrittlement Threshold in Steel by the Incremental Step Loading Technique

    F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    F2482 Standard Specification for Load-Indicating Externally Threaded Fasteners

    F2660 Standard Test Method for Qualifying Coatings for Use on A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    A194/A194M Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both

    A325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    A354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A490M Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)

    A563 Specification for Carbon and Alloy Steel Nuts

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    D3951 Practice for Commercial Packaging

    E384 Test Method for Knoop and Vickers Hardness of Materials

    E709 Guide for Magnetic Particle Testing

    E1444 Practice for Magnetic Particle Testing

    F436 Specification for Hardened Steel Washers

    F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F959 Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners

    F1136 Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1789 Terminology for F16 Mechanical Fasteners

    F2328 Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs

    F2833 Specification for Corrosion Protective Fastener Coatings with Zinc Rich Base Coat and Aluminum Organic/Inorganic Type

    G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels