ASTM A194 / A194M - 13 Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A193/A193M Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications

    A320/A320M Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service

    A325 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    A490 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    A563 Standard Specification for Carbon and Alloy Steel Nuts

    A962/A962M Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range

    B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    F432 Standard Specification for Roof and Rock Bolts and Accessories

    F998 Standard Specification for Centrifugal Pump, Shipboard Use

    F1155 Standard Practice for Selection and Application of Piping System Materials

    F1370 Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard

    F1476 Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications

    F1508 Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas and Liquid Services

    F1510 Standard Specification for Rotary Positive Displacement Pumps, Ships Use

    F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength

    F1565 Standard Specification for Pressure-Reducing Valves for Steam Service

    F1718 Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

    F1852 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

    F2437 Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs

    F2716 Standard Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam

    F2798 Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

    A276 Specification for Stainless Steel Bars and Shapes

    A320/A320M Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A962/A962M Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range

    B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel

    B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    B696 Specification for Coatings of Cadmium Mechanically Deposited

    B766 Specification for Electrodeposited Coatings of Cadmium

    E112 Test Methods for Determining Average Grain Size

    E566 Practice for Electromagnetic (Eddy-Current) Sorting of Ferrous Metals

    F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F1940 Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

    F1941 Specification for Electrodeposited Coatings on Threaded Fasteners (Unified Inch Screw Threads (UN/UNR))

    F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners