ASTM A193 / A193M - 14 Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A453/A453M Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels

    A962/A962M Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range

    C852 Standard Guide for Design Criteria for Plutonium Gloveboxes

    C1533 Standard Guide for General Design Considerations for Hot Cell Equipment

    C1725 Standard Guide for Hot Cell Specialized Support Equipment and Tools

    F38 Standard Test Methods for Creep Relaxation of a Gasket Material

    F998 Standard Specification for Centrifugal Pump, Shipboard Use

    F1155 Standard Practice for Selection and Application of Piping System Materials

    F1276 Standard Test Method for Creep Relaxation of Laminated Composite Gasket Materials

    F1370 Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard

    F1476 Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications

    F1508 Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas and Liquid Services

    F1510 Standard Specification for Rotary Positive Displacement Pumps, Ships Use

    F1565 Standard Specification for Pressure-Reducing Valves for Steam Service

    F1718 Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

    F2437 Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs

    F2482 Standard Specification for Load-Indicating Externally Threaded Fasteners

    F2716 Standard Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam

    F2798 Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

    A194/A194M Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both

    A320/A320M Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service

    A354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A788/A788M Specification for Steel Forgings, General Requirements

    A962/A962M Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range

    B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel

    B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    B696 Specification for Coatings of Cadmium Mechanically Deposited

    B766 Specification for Electrodeposited Coatings of Cadmium

    E18 Test Methods for Rockwell Hardness of Metallic Materials

    E21 Test Methods for Elevated Temperature Tension Tests of Metallic Materials

    E112 Test Methods for Determining Average Grain Size

    E139 Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials

    E150 Recommended Practice for Conducting Creep and Creep-Rupture Tension Tests of Metallic Materials Under Conditions of Rapid Heating and Short Times

    E151 Recommended Practice for Tension Tests of Metallic Materials at Elevated Temperatures with Rapid Heating and Conventional or Rapid Strain Rates

    E292 Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials

    E328 Test Methods for Stress Relaxation for Materials and Structures

    E566 Practice for Electromagnetic (Eddy-Current) Sorting of Ferrous Metals

    E709 Guide for Magnetic Particle Testing

    F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F1940 Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

    F1941 Specification for Electrodeposited Coatings on Threaded Fasteners (Unified Inch Screw Threads (UN/UNR))

    F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners